Emerson Series 3000 MVD - Manuals

Configuration and Use Manual 1 Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Chapter 1 Before You Begin 1.1 About this manual This manual explains how to install, configure, and use the following Micro Motion ® Series 3000 devices: • Model 3500 or Model 3700 ...

2 Micro Motion ® Series 3000 MVD Transmitters and Controllers Before You Begin 1.3 European installations This Micro Motion product complies with all applicable European directives when properly installed in accordance with the instructions in this manual. Refer to the EC declaration of conformity f...

Configuration and Use Manual 3 Before You Begin Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin 1.6 Communication tools You can communicate with a Series 3000 device using any of the following communication tools: • The local display • ProLink II v2.5 and highe...

4 Micro Motion ® Series 3000 MVD Transmitters and Controllers Before You Begin 5. Perform startup procedures (Chapter 16). 6. Learn to use the Series 3000 device in operation mode (Chapters 17 through 19). 7. Learn how to view, start and stop, and reset totalizers (Chapter 20). 8. Establish a meter ...

Configuration and Use Manual 5 Before You Begin Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin 1.9 Micro Motion customer service For customer service, phone the support center nearest you: • In the U.S.A., phone 800-522-MASS (800-522-6277) (toll-free) • In Can...

Configuration and Use Manual 7 Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Chapter 2 Installation 2.1 Overview This chapter provides supplemental installation information for all Series 3000 devices. 2.2 Installation procedure To install your Series 3000 de...

8 Micro Motion ® Series 3000 MVD Transmitters and Controllers Installation 2.4 Model 3350 or Model 3700 safety precautions 2.5 Environmental requirements Note: This section applies to all Series 3000 devices. In addition to the temperature requirements described in the QRG, the following environment...

Configuration and Use Manual 9 Installation Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin 2.8 Model 3350 or Model 3700 display cover orientation (optional) Note: This section applies only to Model 3350 or Model 3700 devices. If desired, you can reposition the...

10 Micro Motion ® Series 3000 MVD Transmitters and Controllers Installation 2.9 Installing the remote core processor Note: This section applies only to Model 3500 or Model 3700 devices in remote core processor with remote transmitter installations. For dimensions of the remote core processor, see Fi...

Configuration and Use Manual 11 Installation Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Remote core processor with remote transmitter installations also require 9-wire cable. Micro Motion offers three types of 9-wire cable: jacketed, shielded, and armored....

12 Micro Motion ® Series 3000 MVD Transmitters and Controllers Installation Figure 2-2 I/O terminal locations Figure 2-3 I/O terminal labels Model 3300 or Model 3500 panel-mount Input/output wiring terminals Model 3300 or Model 3500 rack-mount Input/output wiring terminals Model 3350 or Model 3700 f...

Configuration and Use Manual 13 Installation Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin 2.11.2 Grounding For all Series 3000 devices, the shields from the I/O wires should be grounded at a single point. Ground the shields at the remote device, not at the S...

Configuration and Use Manual 15 Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Chapter 3 Digital Communications Setup 3.1 About this chapter This chapter explains how to install wiring for digital communications between the Series 3000 device and a remote devi...

16 Micro Motion ® Series 3000 MVD Transmitters and Controllers Digital Communications Setup You may also order the IC521A-F signal converter with a ticket printer. Contact Micro Motion for the appropriate ETO (engineered-to-order) number. Depending on your remote device, you may also need a 9-pin to...

Configuration and Use Manual 19 Digital Communications Setup Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin 3.4 Setting up Bell 202 communications Follow the steps below to set up Bell 202 communications between the Series 3000 device and a remote device. 1. L...

20 Micro Motion ® Series 3000 MVD Transmitters and Controllers Digital Communications Setup Figure 3-4 Model 3300 or Model 3500 with HART interface – Screw-type or solder-tail connectors Figure 3-5 Model 3300 or Model 3500 with HART interface – I/O cables HART interface Wire size is 24 AWG (0,25 mm ...

22 Micro Motion ® Series 3000 MVD Transmitters and Controllers Digital Communications Setup Figure 3-8 HART multidrop wiring with SMART FAMILY ™ transmitters and a configuration tool Figure 3-9 Wiring for pressure or external temperature compensation ProLink II v2.x, HART Communicator, or AMS softwa...

Configuration and Use Manual 23 Digital Communications Setup Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Figure 3-10 Wiring for HART Tri-Loop Figure 3-11 Wiring for pressure or external temperature compensation with HART Tri-Loop DC power supply Series 3000...

Configuration and Use Manual 25 Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Chapter 4 Using the Display and Menu System 4.1 About this chapter This chapter explains how to use the Series 3000 display and menu system. Using the display, you can move through ...

26 Micro Motion ® Series 3000 MVD Transmitters and Controllers Using the Display and Menu System 4.3 Menu systems Most Series 3000 display functions are organized into two menu systems: • The Management menu allows you to perform configuration and maintenance tasks. • The View menu allows you to mon...

Configuration and Use Manual 27 Using the Display and Menu System Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Installation Using the Dis p la y Digi tal Comm unic atio ns...

28 Micro Motion ® Series 3000 MVD Transmitters and Controllers Using the Display and Menu System Figure 4-5 Pressing Security button from Process Monitor screen – Security enabled 4.3.2 Shortcuts From any point in the menu system, you can: • Return to the Management menu (if security is disabled) or...

Configuration and Use Manual 29 Using the Display and Menu System Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Installation Using the Dis p la y Digi tal Comm unic atio ns...

Configuration and Use Manual 31 Using the Display and Menu System Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Installation Using the Dis p la y Digi tal Comm unic atio ns Setup Befo re Y o u Begin Installation Using the Dis p la y Digi tal Comm unic atio ns...

Configuration and Use Manual 33 C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Chapter 5 Configuring Security and Language 5.1 About this chapter This chapter explains how to configure security and select the language for the ...

34 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Security and Language 5.3 Security Security can be used for the following three functions: • To control access to the Management menu • To write-protect the Series 3000 device configuration • To control how process totalizers...

Configuration and Use Manual 35 Configuring Security and Language C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e 5.3.3 Controlling process totalizer and process inventory reset This feature allows you to specify the methods th...

Configuration and Use Manual 37 C o nfiguring System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Chapter 6 Configuring System Data 6.1 About this chapter This chapter explains how to configure system data. System parameters are listed in Figure 6-...

38 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring System Data 6.3 System parameters System parameters are defined in Table 6-1. 6.3.1 Alarm severity Alarms are organized into four categories. Within each category, alarms are classified into three levels of severity. The seve...

Configuration and Use Manual 39 C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Chapter 7 Configuring Inputs 7.1 About this chapter This chapter explains how to configure inputs. Inputs include all the software parameters liste...

40 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs Figure 7-1 Inputs menu – Core processor parameters Inputs Flow variables• Flow damping• Flow direction• Mass units• Mass low flow cutoff• Volume flow type• Volume units (2) • Std gas volume units (3) • Std gas volume c...

Configuration and Use Manual 41 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Figure 7-2 Inputs menu – Frequency input, discrete input, external inputs 7.3 Configuring the core processor parameters Core pro...

42 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs 7.3.1 Enabling and disabling core processor inputs Core processor inputs are enabled by default. By disabling the core processor, you disable all core processor input signals and alarms. Disabling them might be desirab...

Configuration and Use Manual 43 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Figure 7-3 Effect of flow direction on milliamp outputs: 4 mA value = 0 Volume flow type Liquid • Select the desired volume flow...

44 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs Figure 7-4 Effect of flow direction on milliamp outputs: 4 mA value < 0 Example 1 Configuration: • Flow direction = Forward only • mA output: 4 mA = 0 g/s; 20 mA = 100 g/s (See the first graph in Figure 7-3.) As a r...

Configuration and Use Manual 45 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Example 2 Configuration: • Flow direction = Reverse only • mA output: 4 mA = 0 g/s; 20 mA = 100 g/s (See the second graph in Fig...

46 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs Table 7-3 Effect of flow direction on frequency outputs, discrete outputs, totalizers, and digital communications Flow direction value Forward flow (1) (1) Process fluid flowing in same direction as flow direction arro...

Configuration and Use Manual 47 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Pounds per minute lb/min Pounds per hour lb/hr Pounds per day lb/day Short tons (2000 lb) per minute STon/min Short tons (2000 l...

48 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs Gas standard volume flow and standard density If you set Volume Flow Type to Gas Standard Volume, you must enter the standard density of the gas you are going to measure (i.e., the density of the gas at reference condi...

Configuration and Use Manual 49 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e 4. If your gas is not listed, you must describe its properties. a. Select the Enter Other Gas Property radio button. b. Select t...

50 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs To create a special unit, you must: 1. Identify the simplest base volume or mass and base time units for your special mass flow or volume flow unit. For example, to create the special volume flow unit pints per minute ...

Configuration and Use Manual 51 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Density parameters Density parameters are listed and defined in Table 7-8. Density units are listed in Table 7-9. Table 7-8 Dens...

52 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs Temperature parameters Temperature parameters are listed and defined in Table 7-10. Damping A damping value is a period of time, in seconds, over which the process variable value will change to reflect 63% of the chang...

Configuration and Use Manual 53 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Cutoffs Cutoffs are user-defined values below which the transmitter reports a value of zero for the specified process variable. ...

54 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs Figure 7-5 Sample calibration tags – T-Series sensors Figure 7-6 Sample calibration tags – All sensors except T-Series Density calibration factors If your sensor tag does not show a D1 or D2 value: • For D1, enter the ...

Configuration and Use Manual 55 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Flow calibration values Two separate values are used to describe flow calibration: a 6-character FCF value and a 4-character FT ...

56 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs LD Optimization is a special compensation that is specifically for hydrocarbon liquids. LD Optimization should not be used with any other process fluids. LD Optimization is available only with certain large sensor size...

Configuration and Use Manual 57 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e 7.4 Configuring the frequency input Frequency input parameters define how the frequency input is used to represent process data....

58 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs For more assistance on configuring the frequency input parameters, see the information provided for configuring the frequency output parameters, in Section 8.5. 7.5 Configuring the discrete inputs Note: Be sure to dist...

Configuration and Use Manual 59 Configuring Inputs C o n fig urin g System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e 7.6 Configuring the external inputs External input parameters are used to configure polling. Polling is used to retrieve tempera...

60 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Inputs Density factor (1) 0.0000 g/cm3 per PSI The change in fluid density per PSI. Not all sensors or applications require a pressure correction factor for density. For the value to be used, see the product data sheet for yo...

Configuration and Use Manual 61 Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Chapter 8 Configuring Outputs 8.1 About this chapter This chapter explains how to configure outputs. Outputs include all the software parameters listed in Figure 8...

62 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Outputs Figure 8-1 Outputs menu 3 2 Outputs Discrete outputs Milliamp outputs Frequency output Discrete output 1 2 Milliamp output 1 Polarity • Active high• Active low Assignment • Discrete input 1• Discrete input 2• Discrete...

Configuration and Use Manual 63 Configuring Outputs Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts 8.3 Configuring the discrete outputs You can configure one, two, or three discrete outputs. For each discrete output, you will configure: • Pol...

64 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Outputs 8.3.2 Source variable assignment The ON/OFF states of the discrete output are controlled by the discrete input, discrete event, or process condition assigned to the discrete output as a source variable. See Table 8-2....

Configuration and Use Manual 65 Configuring Outputs Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Flow switch Flow switch is used to indicate that the flow rate of the flow switch source (e.g., mass flow, liquid volume flow) has dropped belo...

66 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Outputs Note: The Fault Indication parameter is designed to put the discrete output in a safe state during a fault condition, and not to indicate that a fault condition is present. If you want to use the discrete output to in...

Configuration and Use Manual 67 Configuring Outputs Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts By default, the Series 3000 device immediately reports a fault when a fault is encountered. You can delay reporting faults by changing the faul...

68 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Outputs LRV and URV Each process variable that can be assigned to a milliamp output has its own 20 mA and 4 mA value (URV and LRV). If you assign a different process variable to a milliamp output, the corresponding LRV and UR...

Configuration and Use Manual 69 Configuring Outputs Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Note: Beginning with rev7.0 of the transmitter software, if the LRV and URV are changed from the defaults, and the milliamp output source is la...

70 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Outputs 8.5 Configuring the frequency output Table 8-7 lists and defines the parameters that can be set for the frequency output. Example Configuration: • Flow damping: 1 • Primary mA output: Mass flow • Frequency output: Mas...

Configuration and Use Manual 71 Configuring Outputs Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts 8.5.1 Frequency = flow If you specify Frequency = Flow, you must also specify Frequency and Flow. Flow is defined as the maximum flowrate appro...

72 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Outputs The resulting Frequency value must be within the range of the frequency output (0 to 10,000 Hz). • If the Frequency value is less than 1 Hz, reconfigure the receiving device for a higher pulses/unit setting. • If the ...

Configuration and Use Manual 73 Configuring Outputs Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Figure 8-4 50% duty cycle If Maximum Pulse Width is set to a non-zero value, the duty cycle is controlled by the crossover frequency : • At fre...

Configuration and Use Manual 75 C o nfiguring System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e Chapter 9 Configuring the Petroleum Measurement Application 9.1 About this chapter This chapter explains how to configure the petroleum measurement ap...

76 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring the Petroleum Measurement Application 9.3 About petroleum measurement The petroleum measurement application enables Correction of Temperature on volume of Liquids , or CTL. In other words, some applications that measure liqui...

Configuration and Use Manual 77 Configuring the Petroleum Measurement Application C o nfiguring System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty & L a n g u a g e C o nfiguring System Data C o n fig urin g API Con fig urin g Inp u ts Config urin g Secu ri ty &...

78 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring the Petroleum Measurement Application 9.4.2 Temperature data For the temperature value to be used in CTL calculation, you can use the temperature data from the sensor, or you can poll an external temperature device: • To use ...

Configuration and Use Manual 79 Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Chapter 10 Configuring Discrete Events 10.1 About this chapter This chapter explains how to configure discrete events. Discrete events include all the software par...

80 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Discrete Events Figure 10-1 Discrete events menu 10.4 Discrete event configuration procedure You can configure 1 to 5 discrete events, as described in the following steps. Step 1 Discrete event Select Discrete event 1 – 5 . S...

Configuration and Use Manual 81 Configuring Discrete Events Con fig urin g Batch C o n fi guri ng Proce ss Mon itor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Step 4 High and low values For the process variable assigned to the selected discrete event, configure a high value, a low value, or hi...

Configuration and Use Manual 83 Con fig urin g Batch Con fig urin g Pr o c ess Mo ni tor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Chapter 11 Configuring the Discrete Batch Application 11.1 About this chapter This chapter explains how to configure the discrete batch application. The discrete ...

84 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring the Discrete Batch Application Figure 11-1 Discrete batch menu 11.3 Batching configuration overview To configure batching, the following general steps are required: 1. From the Discrete Batch menu: a. Configure flow source. b...

Configuration and Use Manual 85 Configuring the Discrete Batch Application Con fig urin g Batch Con fig urin g Pr o c ess Mo ni tor Con fig urin g Ou tpu ts Con fig urin g Eve n ts 2. From the Discrete Outputs menu, configuring the required discrete outputs: • For 1-stage operation, you must configu...

86 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring the Discrete Batch Application 11.5 Control options Select one of the control options defined in Table 11-2. Note: Control options apply to all batch presets. ED net mass flow (3) • Net mass flow rate• Net mass flow is availa...

Configuration and Use Manual 87 Configuring the Discrete Batch Application Con fig urin g Batch Con fig urin g Pr o c ess Mo ni tor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Count up Yes • If set to Yes, the total displayed on screen increases from zero to the target value. • If set to No, th...

88 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring the Discrete Batch Application 11.5.1 One-stage versus two-stage batching If No. of Stages is set to 1 , a single pump or valve is used to control the batch. (You can assign both a pump and a valve if desired, although only o...

Configuration and Use Manual 89 Configuring the Discrete Batch Application Con fig urin g Batch Con fig urin g Pr o c ess Mo ni tor Con fig urin g Ou tpu ts Con fig urin g Eve n ts 11.6.1 Batch preset examples The following examples describe the batch processing sequence for two different batch pres...

90 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring the Discrete Batch Application 11.7 Batch control methods Batch control functions can be performed in four ways: • By using the function buttons on the display (see Section 18.3) • By assigning a discrete input to a batch con...

Configuration and Use Manual 91 Configuring the Discrete Batch Application Con fig urin g Batch Con fig urin g Pr o c ess Mo ni tor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Table 11-4 Batch control assignments Function Default assignment Assignment options ON state actions End None Specify t...

92 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring the Discrete Batch Application 11.7.1 Special cases in batch control There are two common situations in batch control that may require special configuration: • Cleaning/purging the sensor tubes In normal processing, the batch...

Configuration and Use Manual 93 Con fig urin g Batch Con fig urin g Pr o c ess Mo ni tor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Chapter 12 Configuring the Process Monitor 12.1 About this chapter This chapter explains how to configure the process monitor. Parameters are listed in Figure 12-...

94 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring the Process Monitor 12.3 Process monitor screens The Process Monitor Screens menu allows you to specify the process variable that will appear on the display. You can configure five screens, displaying 0 to 4 variables on each...

Configuration and Use Manual 95 Configuring the Process Monitor Con fig urin g Batch Con fig urin g Pr o c ess Mo ni tor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Con fig urin g Batch Con fig urin g Pr o c ess Mo ni tor Con fig urin g Ou tpu ts Con fig urin g Eve n ts Con fig urin g Batch Con...

Configuration and Use Manual 97 Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Chapter 13 Configuring Digital Communications 13.1 About this chapter This chapter explains how to configure digital communications. Only communication para...

Configuration and Use Manual 99 Configuring Digital Communications Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Figure 13-3 Digital communication menu – Bell 202 and Device setup 13.3 Configuring RS-485 parameters RS-485 parameters s...

100 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Digital Communications Polling address Two polling addresses are stored on the Series 3000 device: a Modbus polling address and a HART polling address. • The Modbus polling address can be configured only in the RS-485 menu, ...

Configuration and Use Manual 101 Configuring Digital Communications Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns If no connection is made during the 10-second period, the terminals are automatically reset to RS-485 mode and will rema...

102 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Digital Communications Printer test After configuring the printer, select Printer Test to perform a printer test. A standard test page should be produced at the printer. When the printer test is complete, the display reads “...

Configuration and Use Manual 103 Configuring Digital Communications Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns 13.4.1 Loop current mode Loop current mode is used to fix or unfix the mA output: • If Loop Current Mode is disabled, th...

104 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Digital Communications 13.4.3 Communicating with a remote device After Bell 202 communications have been set up (both wiring and configuration), you can connect to the Series 3000 device using the parameters described in Tab...

Configuration and Use Manual 105 Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Chapter 14 Configuring Custody Transfer 14.1 About this chapter This chapter explains how to configure the custody transfer application. Note: The custody ...

106 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Custody Transfer 14.3 Configuration options The custody transfer application is designed to comply with three different sets of requirements, as defined by two different regulatory agencies. Before configuring the custody tr...

Configuration and Use Manual 107 Configuring Custody Transfer Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns 14.4 Configuring custody transfer (NTEP) To configure custody transfer (NTEP): 1. Referring to Figure 14-1, set World Area to ...

108 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Custody Transfer Figure 14-1 Security menu for custody transfer (NTEP) 14.5 Configuring custody transfer (OIML) and custody transfer (OIML/batch) To configure custody transfer (OIML) or custody transfer (OIML/batch): 1. Refe...

110 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Custody Transfer Note: If a single discrete input is assigned to print both a transfer (OIML) ticket and a standard or batch ticket, only the transfer (OIML) ticket will be printed. With the exception of ticket printing and ...

Configuration and Use Manual 111 Configuring Custody Transfer Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Figure 14-2 Security menu for custody transfer (OIML) and custody transfer (OIML/batch) 14.6 Setting the security switch Secur...

112 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Custody Transfer Figure 14-3 Security switch on panel-mount Model 3300 or Model 3500 14.6.2 Rack-mount devices To set the security switch on a Model 3300 or Model 3500 mounted in a rack: 1. Loosen the captive screws that sec...

Configuration and Use Manual 113 Configuring Custody Transfer Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Figure 14-4 Security switch on rack-mount Model 3300 or Model 3500 Figure 14-5 Installing lockout screws on rack-mount platfor...

114 Micro Motion ® Series 3000 MVD Transmitters and Controllers Configuring Custody Transfer To set the security switch on the Model 3350 or Model 3700: 1. Unscrew the circuit board compartment cover. 2. The security switch is located on the panel inside the circuit board compartment. To secure the ...

Configuration and Use Manual 115 Configuring Custody Transfer Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns 14.7 Installing the weights and measures seal The weights and measures seal must be installed and secured by a weights and mea...

Configuration and Use Manual 117 Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Chapter 15 Ticket Formatting and Printing 15.1 About this chapter This chapter explains how to format and print tickets. To print tickets, digital communic...

118 Micro Motion ® Series 3000 MVD Transmitters and Controllers Ticket Formatting and Printing Table 15-1 Ticket availability Special applications Tickets available Standard Batch (1) (1) Refers to batch tickets when (a) the custody transfer application is not installed, or (b) the custody transfer ...

Configuration and Use Manual 119 Ticket Formatting and Printing Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns 15.3 Standard tickets This section describes the formatting and printing of standard tickets. 15.3.1 Formatting To format st...

120 Micro Motion ® Series 3000 MVD Transmitters and Controllers Ticket Formatting and Printing 15.3.2 Printing You can print standard tickets manually, via the display, or via a discrete input. You can also specify that tickets will be printed automatically if a discrete event occurs. You may use as...

Configuration and Use Manual 121 Ticket Formatting and Printing Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Note: You can assign one or more actions to a single discrete input or discrete event. Other discrete input and discrete eve...

Configuration and Use Manual 123 Ticket Formatting and Printing Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns If the print request occurs: • When flow is not present (the batch is stopped or ended), the batch ticket is printed. • When...

124 Micro Motion ® Series 3000 MVD Transmitters and Controllers Ticket Formatting and Printing Figure 15-3 Ticket configuration menu – Batch (NTEP) tickets 15.5.2 Printing Batch (NTEP) tickets can be printed in several ways: • Automatically, when the batch ends or when a discrete event occurs • Manu...

Configuration and Use Manual 125 Ticket Formatting and Printing Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Auto print To print a batch (NTEP) ticket automatically when the batch target is reached, set the Auto Print parameter for b...

126 Micro Motion ® Series 3000 MVD Transmitters and Controllers Ticket Formatting and Printing Note: The Pre Header, Post Footer, Header Line 1, Header Line 2, and Footer parameters are shared with all ticket types. Any formatting defined for transfer (OIML) tickets is applied to all tickets. Note: ...

Configuration and Use Manual 127 Ticket Formatting and Printing Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns 15.6.2 Printing Transfer (OIML) tickets must be printed manually, using either the PRINT button on the display or a discrete...

128 Micro Motion ® Series 3000 MVD Transmitters and Controllers Ticket Formatting and Printing Display Note: This function is not available if flow is present and Transfer Print Conditions is set to No Flow. To print a transfer (OIML) ticket from the display: 1. From the View menu, select Transfer T...

Configuration and Use Manual 129 Ticket Formatting and Printing Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Note: The Transfer Print Screen and Transfer Screens to Print options are similar to the Transfer Reset Screen and Transfer ...

130 Micro Motion ® Series 3000 MVD Transmitters and Controllers Ticket Formatting and Printing Figure 15-5 Ticket configuration menu – Batch (OIML) tickets Table 15-8 Ticket parameters – Batch (OIML) tickets Variable Default Description Pre header codesPost footer codes None Printer control codes. E...

Configuration and Use Manual 133 Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Chapter 16 Startup Procedures 16.1 About this chapter This chapter explains the procedures that are required for initial startup of the Series 3000 device....

134 Micro Motion ® Series 3000 MVD Transmitters and Controllers Startup Procedures 4. If there are any active alarms, the alarm category will be displayed in the alarm bar. To view, acknowledge, or respond to the alarms, see Chapter 22. Note: Series 3000 transmitters are ready to begin measurement a...

Configuration and Use Manual 135 Startup Procedures Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Configuri ng Custod y T ...

136 Micro Motion ® Series 3000 MVD Transmitters and Controllers Startup Procedures 5. When the calibration is complete: • In the active alarm log, the alarm changes from “active” to “inactive but unacknowledged.” • If the calibration succeeded, a “Success” status is displayed. • If the calibration f...

Configuration and Use Manual 137 Startup Procedures Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Configuri ng Custod y T ...

138 Micro Motion ® Series 3000 MVD Transmitters and Controllers Startup Procedures 16.3.4 Diagnosing sensor zero failure If the Calibrate Zero screen reads “Calibration Failure,” the sensor zero calibration was not successfully completed. “Calibration Failure” could indicate: • Flow of fluid during ...

Configuration and Use Manual 139 Startup Procedures Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Configuri ng Custod y T ...

140 Micro Motion ® Series 3000 MVD Transmitters and Controllers Startup Procedures Milliamp outputs Refer to Figure 16-2 to access and set the output levels of milliamp outputs. 1. Select the milliamp output to be set. 2. Use the cursor control buttons to change the output value. 3. Press SAVE to se...

Configuration and Use Manual 141 Startup Procedures Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Configuri ng Custod y T ransf er Star tup Con fig urin g Tic kets Con fig urin g Di gi tal Comm u n ic a tio ns Configuri ng Custod y T ...

Configuration and Use Manual 143 Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Chapter 17 Operation Mode 17.1 About this chapter This chapter explains how to use the Series 3000 device in operation mode. There are two different operat...

144 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode 17.4 Process monitor operation mode The process monitor, shown in Figure 17-1, is the default operation mode unless the discrete batch application is present. • To scroll through the process monitor, press the left or rig...

Configuration and Use Manual 145 Operation Mode Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e 17.5 Using the View menu When you press VIEW at the operation screen, the View menu is displayed (see Figure 17-2). This menu varies accordi...

146 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode Figure 17-3 Working with the View menu 17.5.1 Active alarm log The platform performs self-diagnostics during operation. If the platform detects certain events or conditions, an alarm message appears in the highlight bar a...

Configuration and Use Manual 147 Operation Mode Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e 17.5.2 Process monitoring This selection displays the process monitor, as described in Section 17.4. The display is identical to the display...

148 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode 17.5.6 Diagnostic monitor The Diagnostic Monitor shows real-time values for sensor flow tube frequency, left and right pickoffs, drive gain, and live zero. Drive gain, pickoff levels, and sensor flow tube frequency values...

Configuration and Use Manual 149 Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Chapter 18 Operation Mode – Batch 18.1 About this chapter This chapter explains how to use the discrete batch control application and how to perform ba...

150 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Batch 18.3 Batch process screen Figure 18-1 shows the Series 3000 display in batch operation mode, ready to start a batch. The display shows that there have been zero kilograms of actual delivery in this batch. When flo...

Configuration and Use Manual 151 Operation Mode – Batch Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Figure 18-1 Series 3000 display in batch mode 18.3.1 Function buttons In Figure 18-2, the display shows that the batch target is...

152 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Batch Figure 18-2 Using batch function buttons Figure 18-3 indicates the actions that are performed by the function buttons during batch operation. Figure 18-3 Function buttons in batch mode DEVICE 1 Preset 1 Actual 4.4...

Configuration and Use Manual 153 Operation Mode – Batch Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e 18.3.2 Cursor control buttons The Lockout Target parameter can be set to allow the operator to change the target directly from t...

154 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Batch Figure 18-5 Batch processing sequences: 2-stage batching, Open Primary at 0% 0% 100% Normal operation Configured values• Open Primary: 0%• Open Secondary: m%• Close Primary: n% Legend• Primary valve• Secondary val...

156 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Batch Example 1 Batch control configuration: • No. of Stages = 2 • Configure Presets By = % of Target Preset configuration: • Target = 100 liters • Open Primary = 0% • m (Open Secondary) = 30% • n (Close Primary) = 70% ...

Configuration and Use Manual 157 Operation Mode – Batch Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e 18.5 Special cases in batch processing This section describes two common situations in batch processing that may require special...

158 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Batch 6. When overshoot has been adequately minimized: a. From the Maintenance menu, select Calibration . b. Select Batch AOC . 7. Select Save Calibration . 8. Press SEL .

Configuration and Use Manual 159 Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Chapter 19 Operation Mode – Custody Transfer 19.1 About this chapter This chapter explains how to use and manage the custody transfer application. The foll...

160 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Custody Transfer Table 19-1 Series 3000 behavior and available functions Custody transfer (NTEP) Custody transfer (OIML) and custody transfer (OIML/batch) Function Secured Unsecured Secured Unsecured Batch processing Ba...

Configuration and Use Manual 163 Operation Mode – Custody Transfer Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e 19.4 Custody transfer (NTEP) This section provides information on the BOL number, the custody transfer transaction, ticke...

164 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Custody Transfer 19.4.4 General use of Series 3000 device This section describes the effect of custody transfer (NTEP) on specific Series 3000 device functions. Information in this section supplements the information in...

Configuration and Use Manual 165 Operation Mode – Custody Transfer Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e 3. End the transaction, either by printing a transfer (OIML) ticket or by using the transfer reset function. • To end a t...

166 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Custody Transfer 19.5.4 Transfer (OIML) and batch (OIML) tickets and ticket printing Printing methods, conditions, and ticket contents for transfer (OIML) and batch (OIML) tickets are described in Table 19-2. Print fail...

Configuration and Use Manual 167 Operation Mode – Custody Transfer Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Print job status For some printer types, a discrete output can be configured to indicate that the ticket could not be pri...

168 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Custody Transfer 19.5.6 General use of Series 3000 device This section describes the effect of custody transfer (OIML) and custody transfer (OIML/batch) on specific Series 3000 device functions. Information in this sect...

Configuration and Use Manual 169 Operation Mode – Custody Transfer Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e If you select Transfer Totalizer: • You can view current transfer, inventory, or transfer and inventory values for the cu...

170 Micro Motion ® Series 3000 MVD Transmitters and Controllers Operation Mode – Custody Transfer 19.6 Clearing a security breach The method used to clear a security breach depends on the cause of the breach. See Table 19-3. Note: Clearing the security breach on the Series 3000 device does not estab...

Configuration and Use Manual 171 Operation Mode – Custody Transfer Operation Mode – Batc h T otaliz ers and In ventories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Figure 19-3 Audit trail menu 19.8.1 Using the audit trail The Current Event Number item on the Audit Trail menu displays ...

Configuration and Use Manual 173 Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Chapter 20 Using Totalizers and Inventories 20.1 About this chapter This chapter explains how to monitor, start, stop, and reset totalizers and invento...

174 Micro Motion ® Series 3000 MVD Transmitters and Controllers Using Totalizers and Inventories In addition, if the custody transfer application is installed and World Area is set to OIML, the process totalizers and inventories are replaced by the following: • Transfer totalizers – track the total ...

Configuration and Use Manual 175 Using Totalizers and Inventories Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Op...

Configuration and Use Manual 177 Using Totalizers and Inventories Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Operation Mode – Ba tc h T o tali z e rs and Inven tories Ope ration Mode – Custod y Tra n s fer Operatio n M o d e Op...

Configuration and Use Manual 179 Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Chapter 21 Measurement Performance 21.1 Overview This chapter describes the following procedures: • Meter verification – see...

Configuration and Use Manual 181 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 21.2.2 Meter validation and meter factors Meter validation can be used with all Series 3000 systems ...

182 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance The flowmeter measures process variables based on fixed points of reference. Calibration adjusts those points of reference. Three types of calibration can be performed: • Zero (see Section 16.3) • Density calibra...

Configuration and Use Manual 183 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance • Measurement adjustment - Meter verification is an indicator of sensor condition, but does not chan...

184 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance Specification uncertainty limit The specification uncertainty limit defines the acceptable degree of variation from factory results, expressed as a percentage. Variation inside the limit is reported as Pass. Vari...

Configuration and Use Manual 185 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Figure 21-1 Meter verification test, original version – ProLink II Verify configuration parameters T...

186 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance Figure 21-2 Meter verification test, original version – Display 21.3.3 Running Smart Meter Verification To run a Smart Meter Verification test: • With ProLink II, see Figure 21-3. • With the display, see Figure 2...

Configuration and Use Manual 187 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Figure 21-3 Smart Meter Verification test – ProLink II Verify configuration parameters Tools > Me...

188 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance Figure 21-4 Smart Meter Verification test – Display Start Meter Verify Progress . . . . . . . . . x % PASS ABORT FAIL Auswahl Ausgangsverhalten setzen Proceed? Ja Ausgang Einstellung Mit Messung fortfahren Letzte...

Configuration and Use Manual 189 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Figure 21-5 Smart Meter Verification test – Communicator Online > 1 Overview > 3 Shortcuts >...

190 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance 21.3.4 Reading and interpreting meter verification test results Pass/Fail/Abort When the test is completed, the result will be reported as Pass, Fail, or Abort: • Pass – The test result is within the specificatio...

Configuration and Use Manual 191 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Detailed test data with ProLink II For each test, the following data is stored on the transmitter: •...

192 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance Figure 21-6 Test result chart The test result chart shows the results for all tests in the ProLink II database, plotted against the specification uncertainty limit. The inlet stiffness and the outlet stiffness ar...

Configuration and Use Manual 193 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Note the following: • The test result chart may not show all test results, and test counters may not...

194 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance Detailed test data with the Communicator Note: Requires Smart Meter Verification. No detailed test data is available with the original version of the meter verification application. For each Smart Meter Verificat...

Configuration and Use Manual 195 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 21.3.5 Setting up automatic or remote execution of the meter verification test Note: Requires Smart ...

196 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance Figure 21-9 Smart Meter Verification scheduler – Display Figure 21-10 Smart Meter Verification scheduler – Communicator 21.4 Performing meter validation To perform meter validation, measure a sample of the proces...

Configuration and Use Manual 197 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 21.5 Performing density calibration Density calibration includes the following calibration points: •...

198 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance Density calibration fluids D1 and D2 density calibration require a D1 (low-density) fluid and a D2 (high-density) fluid. You may use air and water. If you are calibrating a T-Series sensor, the D1 fluid must be a...

Configuration and Use Manual 199 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 21.5.2 Density calibration procedures To perform the low-density calibration: 1. Fill the sensor wit...

200 Micro Motion ® Series 3000 MVD Transmitters and Controllers Measurement Performance 2. If possible, shut off the flow. Otherwise, pump the fluid through the sensor at the lowest flow rate allowed by the process. 3. To ensure stable density, make sure the fluid in the flow tubes remains completel...

Configuration and Use Manual 201 Measurement Performance Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 4. Use any established method to derive an accurate density, in g/cm 3 , for the fluid at line condi...

Configuration and Use Manual 203 Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Chapter 22 Diagnostics and Troubleshooting 22.1 About this chapter This chapter explains how to use the diagnostic software to...

204 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting Erratic non-zero flow rate under no-flow conditions RF interference Check environment for RF interference. See Section 22.11.5. Wiring problem Verify all sensor-to-transmitter wiring and ensure the wires ...

Configuration and Use Manual 207 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance When the cursor is positioned on Current, you can use the RESET button to set a new start time...

208 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting If sensor simulation mode is active, the specified simulated values are substituted for process data from the sensor. Therefore, sensor simulation will affect, for example: • All mass flow, temperature, o...

Configuration and Use Manual 209 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Some alarms can be reclassified. For example: • The default severity level for Alarm A020 (cal...

210 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting The active alarm log provides help for each alarm listed (see Section 22.6.5), and also allows you to acknowledge alarms. It is cleared and regenerated with every Series 3000 power cycle. When the active ...

Configuration and Use Manual 211 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Figure 22-4 Example alarm event log Active alarm log To access the active alarm log from the V...

212 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting The help system will display up to five screens of information. On these screens: • The alarm number is displayed. • An explanation of the alarm is provided. • Instructions for correcting the alarm condit...

Configuration and Use Manual 213 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance A009 Xmtr Initializing Device is performing self-calibration after power-up. Fault Yes No No a...

Configuration and Use Manual 215 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 22.7.2 Sensor alarms Table 22-5 lists all alarms in the Sensor category, with descriptions, su...

216 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting 22.7.3 Process alarms Table 22-6 lists all alarms in the Process category, with descriptions, suggested user actions, and related information. More information on specific process alarms is provided later...

Configuration and Use Manual 219 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Slug flow alarms Slugs – for example, gas in a liquid process or liquid in a gas process – occ...

220 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting If slug limits have been configured, and slug flow occurs: • A slug flow alarm is generated. • All outputs that are configured to represent flow rate hold their last “pre-slug” value for the configured sl...

Configuration and Use Manual 221 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Calibration alarms If a calibration procedure fails: 1. Ensure that there is no flow through t...

Configuration and Use Manual 223 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance A101 mA 1 Fixed Primary mA output is transmitting fixed output level. Info Yes (5) No Change L...

224 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting 22.8 Restoring a working configuration At times it may be easier to start from a known working configuration than to troubleshoot the existing configuration. To do this, you can: • Restore a configuration...

Configuration and Use Manual 225 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 3. Poll to make a connection to the core processor. 4. When the core processor is found, click...

Configuration and Use Manual 227 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 22.11 Diagnosing wiring problems Use the procedures in this section to check the transmitter i...

228 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting 5. Use a voltmeter to test the voltage at the transmitter’s power-supply terminals. Verify that it is within the specified limits (see Appendix A or Appendix B). 22.11.2 Checking the sensor-to-transmitter...

Configuration and Use Manual 229 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 22.11.6 Checking the output wiring and receiving device If you receive an inaccurate frequency...

230 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting 22.17 Checking the calibration Improper calibration can cause the transmitter to send unexpected output values. If the transmitter appears to be operating correctly but sends inaccurate output values, an ...

Configuration and Use Manual 231 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 22.18.3 Excessive drive gain Excessive drive gain can be caused by several problems. See Table...

232 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting 22.18.5 Low pickoff voltage Low pickoff voltage can be caused by several problems. See Table 22-13. 22.19 Checking the core processor Two core processor procedures are available: • You can check the core ...

234 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting 22.19.2 Core processor resistance test (standard core processor only) Note: Perform this test only if an A026 alarm is present. To perform the core processor resistance test: 1. Power down the transmitter...

Configuration and Use Manual 235 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Figure 22-6 Core processor resistance test 22.20 Checking sensor coils and RTD Problems with s...

236 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting 5. Leave the core processor terminal blocks disconnected. At the sensor, remove the lid of the junction box and test each sensor terminal for a short to case by placing one DMM lead on the terminal and th...

Configuration and Use Manual 237 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 4. Disconnect the wires from the core processor terminals. 5. If you have a standard core proc...

238 Micro Motion ® Series 3000 MVD Transmitters and Controllers Diagnostics and Troubleshooting Figure 22-8 Sensor pins – Enhanced core processor 8. There should be no open circuits, i.e., no infinite resistance readings. The LPO and RPO readings should be the same or very close (±5 Ω ). 9. Using th...

Configuration and Use Manual 239 Diagnostics and Troubleshooting Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance 1. If you have a standard core processor: a. Align the three guide pins on the bottom of the c...

Configuration and Use Manual 241 Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Appendix A Specifications – Model 3300 and Model 3500 A.1 Housing and mounting There are two housing and mounting options av...

Configuration and Use Manual 243 Specifications – Model 3300 and Model 3500 Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Figure A-2 Panel-mount dimensions for Model 3300 or Model 3500 with I/O cables 6 ...

Configuration and Use Manual 245 Specifications – Model 3300 and Model 3500 Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Figure A-4 Core processor dimensions Note: These dimensions apply only to the cor...

248 Micro Motion ® Series 3000 MVD Transmitters and Controllers Specifications – Model 3300 and Model 3500 A.6.4 Digital communications • One RS-485 port (standard) - Supports Modbus RTU, Modbus ASCII, HART/RS-485, or printer - User-configurable • HART superimposed on primary mA output - Standard HA...

Configuration and Use Manual 249 Specifications – Model 3300 and Model 3500 Dia g nostics and T roub leshooting Spe c ifica tions – Model 3 350 /3 7 0 0 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance A.8 Environmental limits • Ambient temperature: - Operating: –4 to +140 °F (–20 t...

Configuration and Use Manual 251 Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Appendix B Specifications – Model 3350 and Model 3700 B.1 Compartmentalized housing • Compartment with threaded cover contains...

Configuration and Use Manual 253 Specifications – Model 3350 and Model 3700 Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific...

256 Micro Motion ® Series 3000 MVD Transmitters and Controllers Specifications – Model 3350 and Model 3700 Discrete outputs Three discrete outputs • Configurable for the application • Polarity: Active high or active low, software selectable • Power: Internal pull-up to 24 V • Voltage: 24 VDC nominal...

Configuration and Use Manual 257 Specifications – Model 3350 and Model 3700 Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific a tions – Model 330 0 /3 500 Measure ment P e rf ormance Dia g nostics and T roub lesh ooting Specificat ion s – Mo del 3350 /3 700 Specific...

258 Micro Motion ® Series 3000 MVD Transmitters and Controllers Specifications – Model 3350 and Model 3700 B.11 Performance specifications For performance specifications, refer to the sensor specifications. B.12 Cleaning instructions To clean the Model 3350 or Model 3700, use a clean damp cloth. WAR...

Configuration and Use Manual 259 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Appendix C Specifications – Model 3100 C.1 Overview The Model 3100 accessory features relay packs for interfacing with high-energy solenoids, pump starters, or other devices. C.2 Relay...

Configuration and Use Manual 261 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Appendix D Installing Relays D.1 About this appendix This appendix explains how to install relay modules for the Series 3000 device. Relays are used to connect the device’s discrete ou...

262 Micro Motion ® Series 3000 MVD Transmitters and Controllers Installing Relays To comply with hazardous area requirements: • Model 3100 relay modules must be mounted into a suitable and classified enclosure that provides ingress protection of at least IP4X according to EN 60529, taking into accou...

Configuration and Use Manual 263 Installing Relays Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Figure D-1 Discrete output circuit D.6 Installing the Model 3100 relay module Follow these steps to install a Model 3100 relay module. Step 1 Mount relay module Mount...

264 Micro Motion ® Series 3000 MVD Transmitters and Controllers Installing Relays Figure D-2 Relay module dimensions TS 32 TS 15 TS 35 x 15 2 1/32 (52) 2 7/32 (56) 2 21/64 (59) 2 (50) 3 3/64 (77) TS 35 x 7.5 8 (203) Dimensions in inches (mm)

Configuration and Use Manual 265 Installing Relays Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Step 2 Connect discrete output terminals to relays Follow the steps below to connect the transmitter/controller’s discrete output wiring terminals to one, two, or thr...

266 Micro Motion ® Series 3000 MVD Transmitters and Controllers Installing Relays Figure D-3 Model 3300 or Model 3500 to Model 3100 – Screw-type or solder-tail connector Figure D-4 Model 3300 or Model 3500 to Model 3100 – I/O cables Relay 3 Relay 1 Wire size is 24 to 16 AWG (0,25 to 1,5 mm 2 ) Relay...

Configuration and Use Manual 267 Installing Relays Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Figure D-5 Model 3350 or Model 3700 to Model 3100 Step 3 Connect relay wiring to control devices Follow the steps below to connect one, two, or three relays to a cont...

268 Micro Motion ® Series 3000 MVD Transmitters and Controllers Installing Relays Figure D-6 Model 3100 relay module to control devices – AC power Figure D-7 Model 3100 relay module to control devices – DC power 24 to 280 VAC (no polarity) Primary control valve or other control device Secondary cont...

Configuration and Use Manual 269 Installing Relays Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 D.7 Installing user-supplied relays Follow these steps to install user-supplied relays. Step 1 Connect discrete output terminals to relays Follow the steps below to c...

270 Micro Motion ® Series 3000 MVD Transmitters and Controllers Installing Relays Figure D-8 Model 3300 or Model 3500 to user-supplied relay – Screw-type or solder-tail connector Figure D-9 Model 3300 or Model 3500 to user-supplied relay – I/O cable User-supplied relays External power supply • 12 to...

Configuration and Use Manual 271 Installing Relays Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Figure D-10 Model 3350 or Model 3700 to user-supplied relay Step 2 Connect relay wiring to control devices The method used to connect the relay to the control device ...

Configuration and Use Manual 273 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Appendix E Default Values and Ranges E.1 Overview This appendix provides information on the default values for most Series 3000 parameters. Where appropriate, valid ranges are also def...

274 Micro Motion ® Series 3000 MVD Transmitters and Controllers Default Values and Ranges Density Density damping 1.6 sec 0.0 – 51.2 sec User-entered value is corrected to nearest value in list of preset values Density units g/cm 3 Density cutoff 0.2 g/cm 3 0.0 – 0.5 g/cm 3 D1 0.00000 D2 1.00000 K1 ...

Configuration and Use Manual 277 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Appendix F Series 3000 Menu Flowcharts F.1 Overview This appendix provides flowcharts for the Series 3000 display menus. F.2 Process monitor Access to the process monitor depends on wh...

278 Micro Motion ® Series 3000 MVD Transmitters and Controllers Series 3000 Menu Flowcharts Figure F-2 Process monitor: Discrete batch application installed F.3 Menu access As shown in Figure F-3: • To access the View menu system, press the VIEW function button. • To access the Management menu syste...

Configuration and Use Manual 281 Series 3000 Menu Flowcharts Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Mo...

282 Micro Motion ® Series 3000 MVD Transmitters and Controllers Series 3000 Menu Flowcharts Figure F-7 Management menu – top level, Security menu, and Language menu Management Menu Language Security Maintenance Configuration Security· Enable/disable· Write Protect (1) · Totalizer Reset (1) Passwords...

Configuration and Use Manual 283 Series 3000 Menu Flowcharts Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Mo...

Configuration and Use Manual 287 Series 3000 Menu Flowcharts Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Model 3 100 Rela y In stal latio n Series 3 000 Men u s Defaults Spec ifications – Mo...

Configuration and Use Manual 289 375 Fi el d Co mm u n ic ato r Saf e ty Lab e ls Sample Tic k et s Pro L in k II Appendix G ProLink II and Pocket ProLink G.1 Overview ProLink II is a Windows-based configuration and management tool for Micro Motion transmitters. It provides access to most Series 300...

290 Micro Motion ® Series 3000 MVD Transmitters and Controllers ProLink II and Pocket ProLink G.3 ProLink II configuration upload/download ProLink II provides a configuration upload/download function which allows you to save configuration sets to your PC. This allows: • Easy backup and restore of de...

Configuration and Use Manual 291 ProLink II and Pocket ProLink 375 Fi el d Co mm u n ic ato r Saf e ty Lab e ls Sample Tic k et s Pro L in k II 5. Add resistance as required. • For HART/Bell 202 connections, the signal converter must be connected across a resistance of 250–600 Ω . See the ProLink II...

292 Micro Motion ® Series 3000 MVD Transmitters and Controllers ProLink II and Pocket ProLink Figure G-1 ProLink II main menu File Preferences• Use External Temperature• Enable Inventory Totals Reset• Enable External Pressure Compensation• Copper RTD Installed options Data Logging (1) Enable/Disable...

Configuration and Use Manual 293 ProLink II and Pocket ProLink 375 Fi el d Co mm u n ic ato r Saf e ty Lab e ls Sample Tic k et s Pro L in k II Figure G-2 ProLink II configuration menu Flow • Flow direction• Flow damp• Flow cal• Mass flow cutoff• Mass flow units• Vol flow cutoff (1) • Vol flow units...

Configuration and Use Manual 297 375 Fie ld Comm unic ator Saf e ty Labels Sample Tic k et s Pro L in k II Appendix H 375 Field Communicator H.1 Overview This appendix provides basic information for connecting and using the 375 Field Communicator with your Series 3000 device. The following topics an...

298 Micro Motion ® Series 3000 MVD Transmitters and Controllers 375 Field Communicator Figure H-1 Communicator Process Vars menu On-Line Menu > 1 Process variables View fld dev vars 1 View basic vars2 View external vars3 View FI vars4 View API vars5 View ED vars6 View batcher vars View output var...

300 Micro Motion ® Series 3000 MVD Transmitters and Controllers 375 Field Communicator Figure H-3 Communicator Diag/Service menu On-Line Menu > 2 Diag/Service Test/Status 1 View status2 Self test Loop test 1 Fix analog out 12 Fix analog out 23 Fix frequency out4 Fix discrete out 15 Fix discrete o...

Configuration and Use Manual 301 375 Field Communicator 375 Fie ld Comm unic ator Saf e ty Labels Sample Tic k et s Pro L in k II Figure H-4 Communicator Basic Setup menu On-Line Menu > 3 Basic Setup Tag PV unit Anlog 1 range values 1 PV URV2 PV LRV 2 3 1 Freq scaling 1 FO scale method · Freq = f...

302 Micro Motion ® Series 3000 MVD Transmitters and Controllers 375 Field Communicator Figure H-5 Communicator Detailed Setup menu On-Line Menu > 4 Detailed Setup 2 1 Charize sensor 1 Sensor selection2 Flow3 Density4 Temp cal factor5 Pressure compensation6 Meter factors7 Polling setup8 External t...

Configuration and Use Manual 305 375 Fi el d Co mm u n ic ato r Saf e ty Lab e ls Sample Tic k et s Pro L in k II Appendix I Sample Tickets I.1 Overview This appendix provides sample tickets for the following ticket types: • Standard tickets - Process monitor tickets – see Figure I-1 - Alarm tickets...

306 Micro Motion ® Series 3000 MVD Transmitters and Controllers Sample Tickets I.2 Standard tickets Figure I-1 Typical process monitor tickets HEADER 1HEADER 2 M. RESET 29-SEP-2003 10:58:27 Mass Flow Rate g/s Current_Value:0.000000 Average:-0.043297 Maximum:56:830570 Minimum:-0.145275 Mass Total g C...

Configuration and Use Manual 307 Sample Tickets 375 Fi el d Co mm u n ic ato r Saf e ty Lab e ls Sample Tic k et s Pro L in k II Figure I-2 Typical alarm tickets HEADER 1HEADER 2 M. RESET 29-SEP-2003 13:27:33 Active Alarm Log Temp. Out-of-RangeINFO 17-JAN-07 14:14:53 Sensor RTD ErrorINFO 17-JAN-07 1...

308 Micro Motion ® Series 3000 MVD Transmitters and Controllers Sample Tickets Figure I-3 Configuration ticket and audit event log ticket For the tickets shown in Figure I-3, codes are used for all items which are selected from a selection list. For example, FO Flow Source code 0 represents mass flo...

310 Micro Motion ® Series 3000 MVD Transmitters and Controllers Sample Tickets Figure I-6 Duplicate tickets I.5 Transfer (OIML) tickets For the tickets shown in Figure I-7, there is no way to distinguish between the following: • No alarm occurred. • An alarm occurred (possibly a security breach), bu...

Configuration and Use Manual 311 Sample Tickets 375 Fi el d Co mm u n ic ato r Saf e ty Lab e ls Sample Tic k et s Pro L in k II Figure I-7 No alarm banner HEADER 1HEADER 2 HEADER 3 HEADER 4 M. RESET 15-MAR-2005 10:57:23 Transfer (BOL): 31 Complete Mass Transfer * 0.906 kg* Volume Transfer * 0.3 US ...

312 Micro Motion ® Series 3000 MVD Transmitters and Controllers Sample Tickets Figure I-8 Alarm banner HEADER 1HEADER 2 HEADER 3 HEADER 4 M. RESET 15-MAR-2005 10:57:23 Transfer (BOL): 36 Complete Mass Transfer * 0.000 kg* Mass Inventory 297.18 kg Volume Transfer * 0.0 US gal* Volume Inventory 137.30...

Configuration and Use Manual 313 Sample Tickets 375 Fi el d Co mm u n ic ato r Saf e ty Lab e ls Sample Tic k et s Pro L in k II Figure I-9 Process variable approved I.6 Batch (OIML) tickets Figure I-10 Original tickets Approved variable: Mass total Transfer complete Approved variable: Volume total ...

Configuration and Use Manual 315 375 Fie ld Comm unic ator Saf e ty Labels Sample Tic k et s Pro L in k II Appendix J Label Maintenance and Replacement J.1 Maintaining and replacing labels Micro Motion product safety labels have been designed in accordance with the voluntary standard ANSI Z535.4. If...

Configuration and Use Manual 317 NE 5 3 His tory In dex Retu rn P o li c y Appendix K Return Policy K.1 General guidelines Micro Motion procedures must be followed when returning equipment. These procedures ensure legal compliance with government transportation agencies and help provide a safe worki...

Configuration and Use Manual 319 NE 5 3 His tory In dex Retu rn P o li c y Appendix L NE 53 History L.1 Overview This appendix documents the change history of the Series 3000 MVD device software. L.2 Software change history Table L-1 describes the change history of the software. Operating instructio...

320 Micro Motion ® Series 3000 MVD Transmitters and Controllers NE 53 History 3/2007 7.00 Software expansion 20001266C Added flow switch to selection list for discrete output assignment Added ability to configure discrete output fault indication Added several HART and Modbus commands Added ability t...

Configuration and Use Manual 323 NE 5 3 His tory In dex Retu rn P o li c y Index Numerics 20 mA value configuration 67troubleshooting 229 375 Field Communicator 297 connecting to Series 3000 device 297menu flowcharts 297requirements 297 4 mA value configuration 67troubleshooting 229 4-wire cable 109...

326 Micro Motion ® Series 3000 MVD Transmitters and Controllers Index security switch 111 Model 3300 or Model 3500 panel- mount 111 Model 3300 or Model 3500 rack-mount 112Model 3350 or Model 3700 field-mount 113 weights and measures seal 115 Customer service, contacting 5Cutoff definition 53density ...

Configuration and Use Manual 331 Index NE 5 3 His tory In dex Retu rn P o li c y installation 263mounting 263power 261replacing 262types 261user-supplied 262, 269 Relay packs 259Remote core processor 10Replacing relays 262Reset batch 91Resistance testing coil 235testing core processor 234 Restore fa...

Micro Motion Inc. USA Worldwide Headquarters 7070 Winchester CircleBoulder, Colorado 80301T +1 303-527-5200+1 800-522-6277 F +1 303-530-8459 Micro Motion Europe Emerson Process ManagementNeonstraat 16718 WX EdeThe NetherlandsT +31 (0) 318 495 555 F +31 (0) 318 495 556 Micro Motion Japan Emerson Proc...