Emerson RTM-ATCA-F120-OPT - Manuals

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 9 About this Manual Overview of Contents This manual is divided into the following chapters and appendices. z Chapter 1, Introduction, on page 21 describes the main features of the RTM z Chapter 2, Hardware Preparation and Installation, on page 25...

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) About this Manual 10 About this Manual Conventions The following table describes the conventions used throughout this manual. NEBS Network Equipment-Building System PCB Printed Circuit Board PICMG PCI Industrial Computer Manufacturers Group PMC PC...

About this Manual RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 11 Summary of Changes This manual has been revised and replaces all prior editions. ... Omission of information from example/command that is not necessary at the time being .. Ranges, for example: 0..4 means one of the integers 0...

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 13 Safety Notes This section provides warnings that precede potentially dangerous procedures throughout this manual. Instructions contained in the warnings must be followed during all phases of operation, service, and repair of this equipment. You...

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) Safety Notes 14 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.Changes or modifications not expressly approved by Eme...

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) Safety Notes 16 SFP/SFP+ Module DamageThe optical port plug protects the sensitive optical fibres against dirt and damage. Dirt and damage can render the SFP/SFP+ module inoperable. Only remove the optical plug when you are ready to connect a cabl...

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 17 Sicherheitshinweise Dieses Kapitel enthält Hinweise, die potentiell gefährlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind. Beachten Sie unbedingt in allen Phasen des Betriebs, der Wartung und der Reparatur des Systems die Anwei...

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) Sicherheitshinweise 18 EMV Das Produkt wurde in einem Emerson Standardsystem getestet. Es erfüllt die für digitale Geräte der Klasse A gültigen Grenzwerte in einem solchen System gemäß den FCC-Richtlinien Abschnitt 15 bzw. EN 55022 Klasse A. Diese...

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) Sicherheitshinweise 20 Verletzungsgefahr Optische SFP/SFP+-Module können als Laserprodukte klassifiziert sein. Wenn Sie solche SFP/SFP+-Module installieren und betreiben, so gelten die entsprechenden Bestimmungen für Laserprodukte für das gesamte ...

Chapter 1 RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 21 Introduction 1.1 Features The RTM-ATCA-F120-OPT is a rear transition module (RTM) as defined in the PICMG 3.0 revision 2.0 AdvancedTCA Base Specification for AdvancedTCA systems. It is designed to be used with the ATCA-F120 base blade...

Introduction RTM-ATCA-F120-OPT Installation and Use (6806800G29C ) 24 1.3 Mechanical Data The following table lists physical dimensions and weight of the RTM. 1.4 Ordering Information Consult your local Emerson sales representative for available RTM variants and their order numbers. Table 1-2 Mechan...

Chapter 2 RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 25 Hardware Preparation and Installation 2.1 Overview This chapter describes all necessary steps you need to take in order to install the RTM-ATCA-F120-OPT. The main steps are: z Inspect the shipment and unpack the RTM z Make sure enviro...

Hardware Preparation and Installation RTM-ATCA-F120-OPT Installation and Use (6806800G29C ) 26 Any optional items ordered 2. Check for damage and report any damage or differences to the customer service. 2.3 Environmental and Power Requirements The following environmental and power requirements are ...

Hardware Preparation and Installation RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 27 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements Requirement Operating Non-Operating Temperature 0ºC to +...

Hardware Preparation and Installation RTM-ATCA-F120-OPT Installation and Use (6806800G29C ) 28 2.4 Installing and Removing the RTM The RTM can be installed into a powered or non-powered system. 2.4.1 Installing the RTM You can install the RTM into a system if the front blade is already installed or ...

Hardware Preparation and Installation RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 33 The blue LEDs on both the front blade and the RTM start flashing. This indicates that the front blade is informing the shelf manager about its desire to power up the payload of both the front blade and the ...

Hardware Preparation and Installation RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 35 3. Unlatch the upper handle and rotate both handles fully outward. 4. Remove interface cables from face plate connectors, if applicable. 5. Loosen the two RTM face plate screws. 6. Remove the RTM from the s...

Chapter 3 RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 41 Controls, LEDs and Connectors 3.1 Overview This chapter describes: z Face plate LEDs z Face plate Interface connectors z Rear panel connectors

Controls, LEDs and Connectors RTM-ATCA-F120-OPT Installation and Use (6806800G29C ) 42 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate BIXXG1 BIXXG2 H/S COM1 BIXGE2 BIXGE3 BIXGE4 CLOCK CH3 FIXXG1 CLOCK CH2 FIXXG2 FIXXG3 FIXXG4 FIXGE1 FIXG...

Controls, LEDs and Connectors RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 43 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. z Six Fa...

Controls, LEDs and Connectors RTM-ATCA-F120-OPT Installation and Use (6806800G29C ) 44 z Two RJ-45 telecom clocking interfaces for inter-shelf clocking configurations z Serial interface for accessing the main blade’s CPU 3.2.2.1 Fabric Channel Uplinks The RTM provides access to the following six Eth...

Chapter 4 RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 55 Functional Description 4.1 Overview This chapter contains the following information: z Block diagram z Mezzanine management controller

Functional Description RTM-ATCA-F120-OPT Installation and Use (6806800G29C ) 56 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram Telecom Clock Telecom Clock BCM8706 MMC BCM8706 4 x 1000B-BX (BIX) 2 x 1000B-BX (FIX2) 2 x 10GB-CX4 (BIX) 4 x 1...

Functional Description RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 57 4.3 Mezzanine Management Controller The RTM provides the a Mezzanine Management Controller (MMC) based on the Atmega128L controller which is compliant to the IPMI v1.5 standard. The MMC is connected to the front blade's I...

Appendix A RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 63 A Related Documentation A.1 Emerson Network Power - Embedded Computing Documents The Emerson Network Power - Embedded Computing publications listed below are referenced in this manual. You can obtain electronic copies of these public...

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 65 B Block diagram 56 C conventions 10 E Environmental requirements 26 F Fabric channel connectors 44 , 47 Face plate 42 I Installation procedure 28 IPMI sensors 57 L LEDs 43 M Main features 21 Mezzanine management controller 57 R Removal procedur...