Emerson MMI-20019043 - Manuals

12.3 Flow measurement problems ....................................................................................................220 12.4 Density measurement problems ...............................................................................................222 12.5 Temperature measurement pro...

Part I Getting Started Chapters covered in this part: • Before you begin • Quick start Getting Started Configuration and Use Manual 1

1 Before you begin Topics covered in this chapter: • About this manual • Transmitter model code • Communications tools and protocols • Additional documentation and resources 1.1 About this manual This manual provides information to help you configure, commission, use, maintain, andtroubleshoot the M...

Communications tools, protocols, and related information Table 1-1: Communica-tions tool Supported protocols Scope In this manual For more information Display Not applicable Basic configuration andcommissioning Complete user informa-tion. See Appendix A . Not applicable ProLink II • HART/RS-485 • HA...

2 Quick start Topics covered in this chapter: • Power up the transmitter • Check flowmeter status • Make a startup connection to the transmitter • Characterize the flowmeter (if required) • Verify mass flow measurement • Verify the zero 2.1 Power up the transmitter The transmitter must be powered up...

1. Wait approximately 10 seconds for the power-up sequence to complete. Immediately after power-up, the transmitter runs through diagnostic routines andchecks for error conditions. During the power-up sequence, Alarm A009 is active.This alarm should clear automatically when the power-up sequence is ...

2.3 Make a startup connection to the transmitter For all configuration tools except the display, you must have an active connection to thetransmitter to configure the transmitter. Follow this procedure to make your firstconnection to the transmitter. Identify the connection type to use, and follow t...

2.4 Characterize the flowmeter (if required) Display Not available ProLink II • ProLink > Configuration > Device > Sensor Type • ProLink > Configuration > Flow • ProLink > Configuration > Density • ProLink > Configuration > T Series ProLink III Device Tools > Calibratio...

If your sensor tag does not show a DT or TC value, enter the last 3 digits of the density calibration factor. In the sample tag, this value is shown as 4.44 (see Figure 2-1 ). Flow calibration parameters (FCF, FT) Two separate values are used to describe flow calibration: a 6-character FCF value and...

• Review the troubleshooting suggestions for flow measurement issues. See Section 12.3 . 2.6 Verify the zero Verifying the zero helps you determine if the stored zero value is appropriate to yourinstallation, or if a field zero can improve measurement accuracy. The zero verification procedure analyz...

3. If the zero verification procedure fails: a. Confirm that the sensor is completely blocked in, that flow has stopped, and that the sensor is completely full of process fluid. b. Verify that the process fluid is not flashing or condensing, and that it does not contain particles that can settle out...

3. If the zero verification procedure fails: a. Confirm that the sensor is completely blocked in, that flow has stopped, and that the sensor is completely full of process fluid. b. Verify that the process fluid is not flashing or condensing, and that it does not contain particles that can settle out...

Part II Configuration and commissioning Chapters covered in this part: • Introduction to configuration and commissioning • Configure process measurement • Configure device options and preferences • Integrate the meter with the control system • Completing the configuration • Set up the Weights & ...

3 Introduction to configuration and commissioning Topics covered in this chapter: • Configuration flowchart • Default values and ranges • Enable access to the off-line menu of the display • Disable write-protection on the transmitter configuration • Restore the factory configuration 3.1 Configuratio...

3.2 Default values and ranges See Section E.1 to view the default values and ranges for the most commonly used parameters. 3.3 Enable access to the off-line menu of the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY ProLink II ProLink > Configuration > Display > Display Opt...

Tip Write-protecting the transmitter prevents accidental changes to configuration. It does not preventnormal operational use. You can always disable write-protection, perform any required configurationchanges, then re-enable write-protection. 3.5 Restore the factory configuration Display Not availab...

4 Configure process measurement Topics covered in this chapter: • Configure mass flow measurement • Configure volume flow measurement for liquid applications • Configure gas standard volume (GSV) flow measurement • Configure Flow Direction • Configure density measurement • Configure temperature meas...

Tip If the measurement unit you want to use is not available, you can define a special measurement unit. Options for Mass Flow Measurement Unit The transmitter provides a standard set of measurement units for Mass Flow Measurement Unit , plus one user-defined special measurement unit. Different comm...

Define a special measurement unit for mass flow Display Not available ProLink II ProLink > Configuration > Special Units ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Speci...

a. 1 lb/sec = 16 oz/secb. Mass Flow Conversion Factor = 1/16 = 0.0625 4. Set Mass Flow Conversion Factor to 0.0625 . 5. Set Mass Flow Label to oz/sec . 6. Set Mass Total Label to oz . 4.1.2 Configure Flow Damping Display Not available ProLink II ProLink > Configuration > Flow > Flow Damp Pr...

• In general, lower damping values are preferable because there is less chance of data loss, and lesslag time between the actual measurement and the reported value. • For gas applications, Micro Motion recommends setting Flow Damping to 2.56 or higher. The value you enter is automatically rounded do...

Procedure Set Mass Flow Cutoff to the value you want to use. The default value for Mass Flow Cutoff is 0.0 g/sec or a sensor-specific value set at the factory. The recommended setting is 0.05% of the sensor's rated maximum flow rate or avalue below the highest expected flow rate. Do not set Mass Flo...

- The frequency output will report the actual flow rate, and the actual flow rate willbe used in all internal processing. • If the mass flow rate drops below 10 g/sec, both outputs will report zero flow, and 0will be used in all internal processing. 4.2 Configure volume flow measurement for liquid a...

Procedure Set Volume Flow Type to Liquid . 4.2.2 Configure Volume Flow Measurement Unit for liquid applications Display OFF-LINE MAINT > OFF-LINE CONFG > UNITS > VOL ProLink II ProLink > Configuration > Flow > Vol Flow Units ProLink III Device Tools > Configuration > Process ...

Define a special measurement unit for volume flow Display Not available ProLink II ProLink > Configuration > Special Units ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Spe...

a. 1 gal/sec = 8 pints/secb. Volume Flow Conversion Factor = 1/8 = 0.1250 4. Set Volume Flow Conversion Factor to 0.1250 . 5. Set Volume Flow Label to pints/sec . 6. Set Volume Total Label to pints . 4.2.3 Configure Volume Flow Cutoff Display Not available ProLink II ProLink > Configuration > ...

Result: If the volume flow rate drops below 15 l/sec, volume flow will be reported as 0, and0 will be used in all internal processing. Example: Cutoff interaction with AO Cutoff higher than Volume Flow Cutoff Configuration: • mA Output Process Variable : Volume Flow Rate • Frequency Output Process V...

4.3.1 Configure Volume Flow Type for gas applications Display Not available ProLink II ProLink > Configuration > Flow > Vol Flow Type ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure > Manual Setup > Measurements > GSV >...

Procedure Set Standard Gas Density to the standard reference density of the gas you are measuring. Note ProLink II and ProLink III provide a guided method that you can use to calculate the standard densityof your gas, if you do not know it. 4.3.3 Configure Gas Standard Volume Flow Measurement Unit D...

Options for Gas Standard Volume Measurement Unit Table 4-4: Unit description Label Display ProLink II ProLink III Field Communica-tor Normal cubic meters per sec-ond NM3/S Nm3/sec Nm3/sec Nm3/sec Normal cubic meters per mi-nute NM3/MN Nm3/min Nm3/sec Nm3/min Normal cubic meters per hour NM3/H Nm3/hr...

4.3.4 Configure Gas Standard Volume Flow Cutoff Display Not available ProLink II ProLink > Configuration > Flow > Std Gas Vol Flow Cutoff ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure > Manual Setup > Measurements > GSV ...

Example: Cutoff interaction with AO Cutoff higher than Gas Standard Volume FlowCutoff Configuration: • mA Output Process Variable for the primary mA output: Gas Standard Volume Flow Rate • Frequency Output Process Variable : Gas Standard Volume Flow Rate • AO Cutoff for the primary mA output: 15 SLP...

4.4.1 Options for Flow Direction Options for Flow Direction Table 4-5: Flow Direction setting Relationship to Flow Direction ar-row on sensor ProLink II ProLink III Field Communicator Forward Forward Forward Appropriate when the Flow Directionarrow is in the same direction as themajority of flow. Re...

Effect of Flow Direction on the mA output: Lower Range Value = 0 Figure 4-1: Flow Direction = Forward mA output -x 0 x Reverse flow Forward flow 20 12 4 Flow Direction = Reverse, Negate Forward mA output -x 0 x Reverse flow Forward flow 20 12 4 Flow Direction = Absolute Value, Bidirectional, Negate ...

• Under conditions of reverse flow or zero flow, the mA output is 4 mA. • Under conditions of forward flow, up to a flow rate of 100 g/sec, the mA outputvaries between 4 mA and 20 mA in proportion to the flow rate. • Under conditions of forward flow, if the flow rate equals or exceeds 100 g/sec, the...

Effect of the Flow Direction parameter and actual flow direction on flowvalues reported via digital communications Table 4-8: Flow Direction setting Actual flow direction Forward Zero flow Reverse Forward Positive 0 Negative Reverse Positive 0 Negative Bidirectional Positive 0 Negative Absolute Valu...

4.5.1 Configure Density Measurement Unit Display OFF-LINE MAINT > OFF-LINE CONFG > UNITS > DENS ProLink II ProLink > Configuration > Density > Density Units ProLink III Device Tools > Configuration > Process Measurement > Density Field Communicator Configure > Manual Se...

4.5.2 Configure slug flow parameters Display Not available ProLink II • ProLink > Configuration > Density > Slug High Limit • ProLink > Configuration > Density > Slug Low Limit • ProLink > Configuration > Density > Slug Duration ProLink III Device Tools > Configuration ...

The default value for Slug High Limit is 5.0 g/cm 3 . The range is 0.0 to 10.0 g/cm 3 . 3. Set Slug Duration to the number of seconds that the transmitter will wait for a slug flow condition to clear before performing the configured slug flow action. The default value for Slug Duration is 0.0 second...

Overview Damping is used to smooth out small, rapid fluctuations in process measurement. Damping Value specifies the time period (in seconds) over which the transmitter will spread changes in the reported process variable. At the end of the interval, the reported process variablewill reflect 63% of ...

Interaction between Density Damping and Added Damping In some circumstances, both Density Damping and Added Damping are applied to the reported density value. Density Damping controls the rate of change in the density process variable. Added Damping controls the rate of change reported via the mA ou...

4.6.1 Configure Temperature Measurement Unit Display OFF-LINE MAINT > OFF-LINE CONFG > UNITS > TEMP ProLink II ProLink > Configuration > Temperature > Temp Units ProLink III Device Tools > Configuration > Process Measurement > Temperature Field Communicator Configure > ...

Overview Damping is used to smooth out small, rapid fluctuations in process measurement. Damping Value specifies the time period (in seconds) over which the transmitter will spread changes in the reported process variable. At the end of the interval, the reported process variablewill reflect 63% of ...

4.7 Configure the petroleum measurement application The petroleum measurement application enables Correction for the effect of Temperatureon the volume of Liquids (CTL), by calculating and applying a Volume Correction Factor(VCF) to volume measurement. Internal calculations are performed in complian...

Option Setup Polling for tempera-ture a. Ensure that the primary mA output has been wired to support HART polling. b. Choose View > Preferences . c. Enable Use External Temperature . d. Choose ProLink > Configuration > Polled Variables . e. Choose an unused polling slot.f. Set Polling Contr...

Option Setup A value written bydigital communica-tions a. Choose Online > Configure > Manual Setup > Measurements > External Pressure/Temperature > Temperature . b. Set External Temperature to Enabled . c. Perform the necessary host programming and communications setup to write temper...

API reference tables, associated process fluids, and associated calculation values (continued) Table 4-13: Tablename Process fluid CTL source data Reference temperature Density unit 53B Generalized products Observed density andobserved temperature 15 °C (configurable) Base densityRange: 653 to1075 k...

Option Setup A value written bydigital communica-tions a. Choose View > Preferences . b. Enable Use External Temperature . c. Perform the necessary host programming and communications setup to write temperature data to the transmitter at appropri-ate intervals. Note If the Weights & Measures ...

Option Setup Polling for tempera-ture a. Ensure that the primary mA output has been wired to support HART polling. b. Choose Online > Configure > Manual Setup > Measurements > External Pressure/Temperature > Temperature . c. Enable External Temperature . d. Choose Online > Configur...

Tip If the standard matrices are not appropriate for your application, you can build a custom matrix orpurchase a custom matrix from Micro Motion. Standard concentration matrices and associated measurement units Table 4-14: Matrix name Description Density unit Temperatureunit Concentrationunit Deg B...

Derived variables and calculated process variables (continued) Table 4-15: Derived Variable Description Calculated process variables Density atreferencetempera-ture Standardvolumeflow rate Specificgravity Concen-tration Net massflow rate Net vol-ume flowrate Concentration de-rived from specificgravi...

Option Setup A value written bydigital communica-tions a. Set Pressure Units to the desired unit. b. Perform the necessary host programming and communications setup to write pressure data to the transmitter at appropriate in-tervals. Note If the Weights & Measures application is implemented and ...

9. If you want to use digital communications, click Apply , then perform the necessary host programming and communications setup to write temperature data to thetransmitter at appropriate intervals. Postrequisites If you are using an external pressure value, verify the setup by checking the External...

Option Setup A user-configuredstatic pressure val-ue a. Set Pressure Unit to the desired unit. b. Set Compensation Pressure to the desired value. Polling for pressure a. Ensure that the primary mA output has been wired to support HART polling. b. Choose Online > Configure > Manual Setup > M...

5 Configure device options and preferences Topics covered in this chapter: • Configure the transmitter display • Enable or disable operator actions from the display • Configure security for the display menus • Configure response time parameters • Configure alarm handling • Configure informational pa...

The languages available depend on your transmitter model and version. 5.1.2 Configure the process variables shown on the display Display Not available ProLink II ProLink > Configuration > Display ProLink III Device Tools > Configuration > Transmitter Display > Display Variables Field ...

Display variable Process variable assignment Display Variable 10 None Display Variable 11 None Display Variable 12 None Display Variable 13 None Display Variable 14 None Display Variable 15 None Configure Display Variable 1 to track the primary mA output Display OFF-LINE MAINT > OFF-LINE CONFG &g...

Overview Setting Display Precision determines the precision (number of decimal places) shown on the display. You can set Display Precision independently for each variable. Setting Display Precision does not affect the actual value of the process variable. Procedure 1. Select a process variable. 2. S...

5.1.5 Enable or disable automatic scrolling through the display variables Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > AUTO SCRLL ProLink II ProLink > Configuration > Display > Display Options > Display Auto Scroll ProLink III Device Tools > Configuration > Transmit...

Procedure Enable or disable Backlight . The default setting is Enabled . 5.1.7 Enable or disable Status LED Blinking Display Not available ProLink II ProLink > Configuration > Display > Display Options > Display Status LED Blinking ProLink III Device Tools > Configuration > Transmi...

5.2.1 Enable or disable Totalizer Start/Stop from the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > TOTALS STOP ProLink II ProLink > Configuration > Display > Display Options > Display Start/Stop Totalizers ProLink III Device Tools > Configuration > Totalizer...

Restrictions • This parameter does not apply to inventories. You cannot reset inventories from the display. • You cannot use the display to reset all totalizers as a group. You must reset totalizersindividually. • If the petroleum measurement application is installed on your computer, the operator m...

Option Description Enabled (default) Operators can use a single display command to acknowledge all alarmsat once. Disabled Operators cannot acknowledge all alarms at once, they must be ac-knowledged individually. 5.3 Configure security for the display menus Display OFF-LINE MAINT > OFF-LINE CONFG...

3. To require a password for access to the maintenance section of the off-line menuand the Smart Meter Verification menu, enable or disable Off-Line Password . Option Description Enabled Operator is prompted for the off-line password at entry to the Smart MeterVerification menu (if applicable) or en...

5.4.1 Configure Update Rate Display Not available ProLink II ProLink > Configuration > Device > Update Rate ProLink III Device Tools > Configuration > Process Measurement > Response > Update Rate Field Communicator Configure > Manual Setup > Measurements > Update Rate O...

Effects of Update Rate = Special Incompatible features and functions Special mode is not compatible with the following features and functions: • Enhanced events. Use basic events instead. • All calibration procedures. • Zero verification. • Restoring the factory zero or the prior zero. If required, ...

5.4.2 Configure Calculation Speed (Response Time) Display Not available ProLink II ProLink > Configuration > Device > Response Time ProLink III Device Tools > Configuration > Process Measurement > Response > Calculation Speed Field Communicator Not available Overview Calculation...

5.5.1 Configure Fault Timeout Display Not available ProLink II ProLink > Configuration > Analog Output > Last Measured Value Timeout ProLink > Configuration > Frequency/Discrete Output > Frequency > Last Measured Value Timeout ProLink III Device Tools > Configuration > Fau...

Overview Use Status Alarm Severity to control the fault actions that the transmitter performs when it detects an alarm condition. Restrictions • For some alarms, Status Alarm Severity is not configurable. • For some alarms, Status Alarm Severity can be set only to two of the three options. Tip Micro...

Status alarms and Status Alarm Severity Table 5-2: Alarm code Status message Default severity Notes Configurable? A001 EEPROM Error (Core Pro-cessor) Fault No A002 RAM Error (Core Processor) Fault No A003 No Sensor Response Fault Yes A004 Temperature Overrange Fault No A005 Mass Flow Rate Overrange ...

Status alarms and Status Alarm Severity (continued) Table 5-2: Alarm code Status message Default severity Notes Configurable? A114 mA Output 2 Fixed Informational Can be set to either Informational or Ignore , but cannot be set to Fault . Yes A115 No External Input or PolledData Informational Yes A1...

- Message - Date • Sensor parameters - Sensor Serial Number - Sensor Material - Sensor Liner Material - Sensor Flange Type 5.6.1 Configure Descriptor Display Not available ProLink II ProLink > Configuration > Device > Descriptor ProLink III Device Tools > Configuration > Informational...

5.6.3 Configure Date Display Not available ProLink II ProLink > Configuration > Device > Date ProLink III Device Tools > Configuration > Informational Parameters > Transmitter Field Communicator Configure > Manual Setup > Info Parameters > Transmitter Info > Date Overvi...

5.6.5 Configure Sensor Material Display Not available ProLink II ProLink > Configuration > Sensor > Sensor Matl ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information &...

5.6.7 Configure Sensor Flange Type Display Not available ProLink II ProLink > Configuration > Sensor > Flange ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information >...

6 Integrate the meter with the control system Topics covered in this chapter: • Configure the transmitter channels • Configure the mA output • Configure the frequency output • Configure the discrete output • Configure events • Configure digital communications 6.1 Configure the transmitter channels D...

Postrequisites For each channel that you configured, perform or verify the corresponding input or outputconfiguration. When the configuration of a channel is changed, the channel’s behavior willbe controlled by the configuration that is stored for the selected input or output type, andthe stored con...

• If you plan to configure an output to report a concentration measurement processvariable, ensure that the concentration measurement application is configured sothat the desired variable is available. • If you are using the HART variables, be aware that changing the configuration of mA Output Proce...

Options for mA Output Process Variable (continued) Table 6-1: Process variable Label Display ProLink II ProLink III Field Communicator Concentration measurement Density at reference RDENS CM: Density @ Reference Density at Reference Temperature ED Dens at Ref Specific gravity SGU CM: Density (Fixed ...

Procedure Set LRV and URV as desired. • LRV is the value of mA Output Process Variable represented by an output of 4 mA. The default value for LRV depends on the setting of mA Output Process Variable . Enter LRV in the measurement units that are configured for mA Output Process Variable . • URV is t...

Default values for Lower Range Value (LRV) and Upper Range Value (URV) (continued) Table 6-2: Process variable LRV URV Concentration 0% 100% Baume 0 10 Specific gravity 0 10 6.2.3 Configure AO Cutoff Display Not available ProLink II ProLink > Configuration > Analog Output > Primary Output &...

Example: Cutoff interaction Configuration: • mA Output Process Variable = Mass Flow Rate • Frequency Output Process Variable = Mass Flow Rate • AO Cutoff = 10 g/sec • Mass Flow Cutoff = 15 g/sec Result: If the mass flow rate drops below 15 g/sec, all outputs representing mass flow willreport zero fl...

Note Added Damping is not applied if the mA output is fixed (for example, during loop testing) or if the mA output is reporting a fault. Added Damping is applied while sensor simulation is active. Procedure Set Added Damping to the desired value. The default value is 0.0 seconds. When you specify a ...

Result: A change in the mass flow rate will be reflected in the mA output over a time periodthat is greater than 3 seconds. The exact time period is calculated by the transmitteraccording to internal algorithms which are not configurable. 6.2.5 Configure mA Output Fault Action and mA Output Fault Le...

Options for mA Output Fault Action and mA Output Fault Level (continued) Table 6-4: Option mA output behavior mA Output Fault Level None Tracks data for the assigned process vari-able; no fault action Not applicable CAUTION! If you set mA Output Fault Action or Frequency Output Fault Action to None ...

Overview Frequency Output Process Variable controls the variable that is reported over the frequency output. Prerequisites If you plan to configure the output to report volume flow, ensure that you have set Volume Flow Type as desired: Liquid or Gas Standard Volume . If you plan to configure an outp...

Options for Frequency Output Process Variable (continued) Table 6-5: Process variable Label Display ProLink II ProLink III Field Communica-tor Net mass flow NET M ED: Net Mass FlowRate Net Mass Flow Rate ED Net Mass flo Net volume flow NET V ED: Net Vol Flow Rate Net Volume Flow Rate ED Net Vol flo ...

6.3.3 Configure Frequency Output Scaling Method Display OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET FO > FO SCALE ProLink II ProLink > Configuration > Frequency/Discrete Output > Frequency > Scaling Method ProLink III Device Tools > Configuration > I/O > Out...

N Number of pulses per flow unit, as configured in the receiving device The resulting Frequency Factor must be within the range of the frequency output (0 to 10,000 Hz): • If Frequency Factor is less than1 Hz,reconfigure the receiving device for a higher pulses/unit setting. • If Frequency Factor is...

The ON signal may be the high voltage or 0.0 V , depending on Frequency Output Polarity . Interaction of Frequency Output Maximum Pulse Width and FrequencyOutput Polarity Table 6-7: Polarity Pulse width Active High Active Low Procedure Set Frequency Output Maximum Pulse Width as desired. The default...

Note For some faults only: If Last Measured Value Timeout is set to a non-zero value, the transmitter will not implement the fault action until the timeout has elapsed. Procedure 1. Set Frequency Output Fault Action as desired. The default value is Downscale (0 Hz). 2. If you set Frequency Output Fa...

• Discrete Output Polarity • Discrete Output Fault Action Restriction Before you can configure the discrete output, you must configure a channel to operate as a discreteoutput. Important Whenever you change a discrete output parameter, verify all other discrete output parametersbefore returning the ...

Configure Flow Switch parameters Display OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET DO > CONFIG FL SW ProLink II • ProLink > Configuration > Flow > Flow Switch Variable • ProLink > Configuration > Flow > Flow Switch Setpoint • ProLink > Configuration > F...

6.4.2 Configure Discrete Output Polarity Display OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET DO > DO POLAR ProLink II ProLink > Configuration > Frequency/Discrete Output > Discrete Output > DO Polarity ProLink III Device Tools > Configuration > I/O > Outputs...

Typical discrete output circuit Figure 6-1: A. 24 V (Nom) B. 3.2 K Ω C. Out+ D. Out − 6.4.3 Configure Discrete Output Fault Action Display Not available ProLink II ProLink > Configuration > Frequency/Discrete Output > Discrete Output > DO Fault Action ProLink III Device Tools > Config...

Procedure Set Discrete Output Fault Action as desired. The default setting is None . Options for Discrete Output Fault Action Options for Discrete Output Fault Action Table 6-11: Label Discrete output behavior Polarity= Active High Polarity= Active Low Upscale • Fault: discrete output is ON(site-spe...

6.5.1 Configure a basic event Display Not available ProLink II ProLink > Configuration > Events ProLink III Device Tools > Configuration > Events > Basic Events Field Communicator Not available Overview A basic event is used to provide notification of process changes. A basic event oc...

Options for Enhanced Event Action Options for Enhanced Event Action Table 6-12: Action Label Display ProLink II ProLink III Field Communicator Standard None (default) NONE None None None Start sensor zero START ZERO Start Sensor Zero Start Sensor Zero Perform auto zero Start/stop all totaliz-ers STA...

6.6 Configure digital communications The digital communications parameters control how the transmitter will communicateusing digital communications. Your transmitter supports the following types of digital communications: • HART/Bell 202 over the primary mA terminals • HART/RS-485 over the RS-485 te...

2. Ensure Loop Current Mode ( mA Output Action ) is configured appropriately. Options Description Enabled The primary mA output reports process data as configured. Disabled The primary mA output is fixed at 4 mA and does not report processdata. Important If you use ProLink II or ProLink III to set H...

Options for HART variables Options for HART variables Table 6-13: Process variable Primary Varia-ble (PV) SecondaryVariable (SV) Third Variable(TV) Fourth Varia-ble (QV ) Standard Mass flow rate ✓ ✓ ✓ ✓ Line (Gross) Volume flow rate ✓ ✓ ✓ ✓ Temperature ✓ ✓ ✓ Density ✓ ✓ ✓ Drive gain ✓ ✓ ✓ Mass total...

Options for HART variables (continued) Table 6-13: Process variable Primary Varia-ble (PV) SecondaryVariable (SV) Third Variable(TV) Fourth Varia-ble (QV ) ED standard volume flow rate ✓ ✓ ✓ ✓ ED standard volume total ✓ ED standard volume inventory ✓ ED net mass flow rate ✓ ✓ ✓ ✓ ED net mass total ✓...

4. Set Parity , Stop Bits , and Baud Rate as appropriate for your network. 5. Set Floating-Point Byte Order to match the byte order used by your Modbus host. Code Byte order 0 1–2 3–4 1 3–4 1–2 2 2–1 4–3 3 4–3 2–1 See Table 6-15 for the bit structure of bytes 1, 2, 3, and 4. Bit structure of floatin...

Overview Digital Communications Fault Action specifies the values that will be reported via digital communications if the transmitter encounters an internal fault condition. Procedure Set Digital Communications Fault Action as desired. The default setting is None . Options for Digital Communications...

7 Completing the configuration Topics covered in this chapter: • Test or tune the system using sensor simulation • Back up transmitter configuration • Enable write-protection on the transmitter configuration 7.1 Test or tune the system using sensor simulation Use sensor simulation to test the system...

Option Required values Sine PeriodMinimumMaximum 4. For density, set Wave Form as desired and enter the required values. Option Required values Fixed Fixed Value Sawtooth PeriodMinimumMaximum Sine PeriodMinimumMaximum 5. For temperature, set Wave Form as desired and enter the required values. Option...

• All mass flow rate, temperature, and density values shown on the display orreported via outputs or digital communications • The mass total and mass inventory values • All volume calculations and data, including reported values, volume totals, andvolume inventories • All mass, temperature, density,...

8 Set up the Weights & Measures application Topics covered in this chapter: • Weights & Measures application • Set up the Weights & Measures application using ProLink II • Set up the Weights & Measures application using ProLink III Information in this chapter is applicable only if yo...

Metrologicalsecurity Metrological security protects the transmitter from all changes thatwould affect measurement. This includes changes to configuration andsome maintenance procedures.Micro Motion implements metrological security via “software security.”Software security is a setting inside the tra...

FVZ is a diagnostic variable that monitors the zero value over a period of 3 minutes. It must be read during meter commissioning to comply with MID requirements forWeights & Measures applications in Measuring Instrument Directive (MID) 2004/22/EC. Refer to your Standard Operating Procedures docu...

Part III Operations, maintenance, and troubleshooting Chapters covered in this part: • Transmitter operation • Operate the transmitter with the Weights & Measures application • Measurement support • Troubleshooting Operations, maintenance, and troubleshooting Configuration and Use Manual 147

9 Transmitter operation Topics covered in this chapter: • Record the process variables • View process variables • View transmitter status using the status LED • View and acknowledge status alarms • Read totalizer and inventory values • Start and stop totalizers and inventories • Reset totalizers • R...

9.2 View process variables Display Scroll to the desired process variable. If AutoScroll is enabled, you can wait until the proc- ess variable is displayed. See Section 9.2.1 for more information. ProLink II ProLink > Process Variables ProLink > API process variables (petroleum measurement app...

Transmitter display features Figure 9-1: A B C D E F G H A. Status LEDB. Display (LCD panel)C. Process variableD. Scroll optical switch E. Optical switch indicator: turns red when either Scroll or Select is activated F. Select optical switch G. Unit of measure for process variableH. Current value of...

9.3 View transmitter status using the status LED The status LED shows the current alarm condition of the transmitter. The status LED islocated on the face of the transmitter. Observe the status LED. • If your transmitter has a display, you can view the status LED with the transmitterhousing cover in...

Using the display to view and acknowledge the status alarms Figure 9-2: SEE ALARM Yes Scroll and Select simultaneously for 4 seconds ACK ALL Yes EXIT Select No Alarm code Scroll ACK Yes Select No Active/ unacknowledged alarms? No Yes Select NO ALARM EXIT Scroll Scroll Select Scroll Scroll Select Is ...

Postrequisites • To clear the following alarms, you must correct the problem, acknowledge thealarm, then power-cycle the transmitter: A001, A002, A010, A011, A012, A013,A018, A019, A022, A023, A024, A025, A028, A029, A031. • For all other alarms: - If the alarm is inactive when it is acknowledged, i...

9.4.3 View and acknowledge alerts using ProLink III You can view a list containing all alerts that are active, or inactive and have beenunacknowleged. From this list, you can acknowlege individual alerts or choose toacknowledge all alerts at once.1. View alerts on the ProLink III main screen under A...

• To refresh the list of active or unacknowledged alarms, press Service Tools > Alerts > Refresh Alerts . 9.4.5 Alarm data in transmitter memory The transmitter maintains three sets of data for every alarm that is posted. For each alarm occurrence, the following three sets of data are maintain...

Overview Totalizers keep track of the total amount of mass or volume measured by the transmittersince the last totalizer reset. Inventories keep track of the total amount of mass or volumemeasured by the transmitter since the last inventory reset. Tip You can use the inventories to keep a running to...

9.7 Reset totalizers Display See Section 9.7.1 . ProLink II ProLink > Totalizer Control > Reset Mass Total ProLink > Totalizer Control > Reset Volume Total ProLink > Totalizer Control > Reset Gas Volume Total ProLink > Totalizer Control > Reset ProLink III Device Tools > T...

3. Scroll until RESET appears beneath the current totalizer value. 4. Select . 5. Select again to confirm. 6. Scroll to EXIT . 7. Select . • To reset the volume totalizer: 1. Scroll until the volume totalizer value appears. 2. Select . 3. Scroll until RESET appears beneath the current totalizer valu...

10 Operate the transmitter with the Weights & Measures application Topics covered in this chapter: • Operate the transmitter when the Weights & Measures application is installed • Switch between secured and unsecured mode • Clear Status Alarm A027: Security Breach • Replacing the core proces...

• You cannot stop totalizers while the tranmitter is secured. • You cannot reset inventories while the transmitter is secured. 10.1.1 Approved methods to read or obtain process data When the Weights & Measures application is installed, process data is approved forcustody transfer use only if an ...

The display is able to show a maximum of eight characters, including the decimal point.For all totalizer values configured as display variables, the position of the decimal point onthe display is fixed to the configured precision of the display variable. When the totalizer reaches the largest value ...

Transmitter outputs and process data when Approvals= OIML Table 10-4: Function Transmitter status Unsecured Secured Outputs mA output behavior Performs configured fault action Normal Frequency output behavior Performs configured fault action Normal Discrete output behavior Performs configured fault ...

The controls are not accessible in any other way. 10.2.1 Switch between secured and unsecured mode using ProLink II Prerequisites Before switching to unsecured mode, ensure that you will be able to switch back tosecured mode. Because switching to unsecured mode requires breaking the physical seal,sw...

1. Make a service port connection to your transmitter.2. Choose Device Tools > Configuration > Weights & Measures . 3. Set Software Security to Enabled . 10.2.3 Switch between secured and unsecured mode using the switching utility Prerequisites The switching utility must be installed on yo...

11 Measurement support Topics covered in this chapter: • Options for measurement support • Use Smart Meter Verification • Zero the flowmeter • Validate the meter • Perform a (standard) D1 and D2 density calibration • Perform a D3 and D4 density calibration (T-Series sensors only) • Perform temperatu...

11.2.1 Smart Meter Verification requirements To use Smart Meter Verification, the transmitter must be paired with an enhanced coreprocessor, and the Smart Meter Verification option must be ordered for the transmitter. See Table 11-1 for the minimum version of the transmitter, enhanced core processor...

Smart Meter Verification has an output mode called Continuous Measurement that allows the transmitter to keep measuring while the test is in progress. If you choose to run the test in Last Measured Value or Fault modes instead, the transmitter outputs will be held constant for the two minute duratio...

Smart Meter Verification flowchart: Running a test using the display Running a Smart Meter Verification test using the display Figure 11-2: OUTPUTS ARE YOU SURE/YES? . . . . . . . . . . . . . . . x% PASS VERFY ABORTED VERFY CAUTION VERFY Fail Abort RERUN/YES? Yes No Correct condition RUN VERFY CONTI...

You may need to wait a few seconds while ProLink II synchronizes its database withthe transmitter data. 2. Review the information presented on the screen, and click Next . 3. Enter any desired information on the Test Definition screen, and click Next . All information on this screen is optional. 4. ...

Postrequisites View the test results and take any appropriate actions. Run a Smart Meter Verification test using the Field Communicator 1. Navigate to the Smart Meter Verification menu: • Overview > Shortcuts > Meter Verification • Service Tools > Maintenance > Routine Maintenance > M...

• Current flowmeter identification data • Current flow and density configuration parameters • Current zero values • Current process values for mass flow rate, volume flow rate, density, temperature,and external pressure • Customer and test descriptions (if entered by the user) If you use ProLink II ...

Smart Meter Verification flowchart: Viewing test results using the display Viewing Smart Meter Verification test results using the display Figure 11-4: RESULTS READ Select xx L STF% RUNCOUNT x Select xx HOURS Select PASS Select xx R STF% Select RESULTS MORE? Select Scroll To Run Verfy Pass Select Sc...

View test result data using ProLink II 1. Choose Tools > Meter Verification > Run Meter Verification and click View Previous Test Results and Print Report . The chart shows test results for all tests stored in the ProLink II database. 2. (Optional) Click Next to view and print a test report. 3...

Fail The test result is not within the specification uncertainty limit. Micro Motionrecommends that you immediately repeat the meter verification test. If duringthe failed test you had set outputs to Continue Measurement , set outputs to Fault or Last Measured Value instead. • If the meter passes th...

Manage scheduled test execution using the display 1. Navigate to the Smart Meter Verification menu. Smart Meter Verification – Top-level menu Figure 11-5: Scroll and Select simultaneously for 4 seconds ENTER METER VERFY Scroll RUN VERFY RESULTS READ SCHEDULE VERFY Select EXIT Scroll Scroll Scroll Sc...

Smart Meter Verification flowchart: Scheduling test execution using the display Scheduling Smart Meter Verification test execution using the display Figure 11-6: SCHEDULE VERFY Select SAVE/YES? TURN OFF SCHED/YES? SET NEXT Select Select Schedule set? Yes Schedule deleted Scroll HOURS LEFT Select Scr...

4. To disable scheduled execution: • To disable execution of a single scheduled test, set Hours Until Next Run to 0. • To disable recurring execution, set Hours Between Recurring Runs to 0. • To disable all scheduled execution, click Turn Off Schedule . Manage scheduled test execution using ProLink ...

• The zero is required by site procedures. • The stored zero value fails the Zero Verification procedure. Prerequisites Before performing a field zero, execute the Zero Verification procedure to see whether ornot a field zero can improve measurement accuracy. See Section 2.6 . Important Do not verif...

2. Navigate to OFFLINE MAINT > ZERO > CAL ZERO and select CAL/YES? . Dots traverse the display while flowmeter zero is in progress. 3. Read the zero result on the display. The display reports CAL PASS if the zero was successful, or CAL FAIL if it was not. Postrequisites Restore normal flow thr...

3. Click Calibrate Zero . 4. Modify Zero Time , if desired. Zero Time controls the amount of time the transmitter takes to determine its zero- flow reference point. The default Zero Time is 20 seconds. For most applications, the default Zero Time is appropriate. 5. Click Perform Auto Zero . The Cali...

11.3.4 Zero the flowmeter using the Field Communicator Zeroing the flowmeter establishes a baseline for process measurement by analyzing thesensor's output when there is no flow through the sensor tubes.1. Prepare the flowmeter: a. Allow the flowmeter to warm up for at least 20 minutes after applyin...

11.4 Validate the meter Display OFF-LINE MAINT > CONFG > UNITS > MTR F ProLink II ProLink > Configuration > Flow ProLink III Device Tools > Configuration > Process Measurement > Flow Device Tools > Configuration > Process Measurement > Density Field Communicator Conf...

Procedure 1. Determine the meter factor as follows: a. Use the flowmeter to take a sample measurement.b. Measure the same sample using the reference device.c. Calculate the meter factor using the following formula: NewMeterFactor ConfiguredMeterFactor ReferenceMeasurement FlowmeterMeasurement = x 2....

MeterFactor Volume 1 MeterFactor Density = Note The following equation is mathematically equivalent to the first equation. You may usewhichever version you prefer. MeterFactor Volume ConfiguredMeterFactor Density Density Flowmeter Density ReferenceDevice = x 3. Ensure that the calculated meter facto...

• If LD Optimization is enabled on your meter, disable it. To do this, choose ProLink > Configuration > Sensor and ensure that the checkbox is not checked. LD Optimizatio n is used only with large sensors in hydrocarbon applications. In some installations, onlyMicro Motion customer service has...

Postrequisites If you disabled LD Optimization before the calibration procedure, re-enable it. 11.5.2 Perform a D1 and D2 density calibration using ProLink III Prerequisites • During density calibration, the sensor must be completely filled with the calibrationfluid, and flow through the sensor must...

D1 and D2 density calibration using ProLink III Figure 11-8: Enter density of D1 fluid D1 calibration Close shutoff valve downstream from sensor Fill sensor with D1 fluid Done Device Tools > Calibration > Density Calibration > Density Calibration – Point 1 (Air) Close Start Calibration Ente...

• Before performing the calibration, record your current calibration parameters. If thecalibration fails, restore the known values. Restriction For T-Series sensors, the D1 calibration must be performed on air and the D2 calibration must beperformed on water. Procedure See Figure 11-9 . D1 and D2 de...

11.6 Perform a D3 and D4 density calibration (T- Series sensors only) For T-Series sensors, the optional D3 and D4 calibration could improve the accuracy of thedensity measurement if the density of your process fluid is less than 0.8 g/cm 3 or greater than 1.2 g/cm 3 . If you perform the D3 and D4 c...

D3 or D3 and D4 density calibration using ProLink II Figure 11-10: Enter density of D3 fluid Calibration in Progress light turns green Calibration in Progress light turns red D3 calibration Close shutoff valve downstream from sensor Fill sensor with D3 fluid Close Enter density of D4 fluid Calibrati...

- Minimum difference of 0.1 g/cm 3 between the density of the D4 fluid and the density of the D3 fluid. The density of the D4 fluid must be greater than thedensity of the D3 fluid. - Minimum difference of 0.1 g/cm 3 between the density of the D4 fluid and the density of water. The density of the D4 ...

D3 or D3 and D4 density calibration using the Field Communicator Figure 11-12: Enter density of D3 fluid Density Calibration Complete message Calibration in Progress message D3 calibration Close shutoff valve downstream from sensor Fill sensor with D3 fluid Fill sensor with D4 fluid D4 calibration O...

Important Consult Micro Motion before performing a temperature calibration. Under normal circumstances,the temperature circuit is stable and should not need an adjustment. Procedure See Figure 11-13 and Figure 11-14 . Temperature calibration using ProLink II Figure 11-13: Enter temperature of low- t...

Temperature calibration using ProLink III Figure 11-14: Enter temperature of low- temperature fluid Temperature Offset calibration Wait until sensor achieves thermal equilibrium Fill sensor with low- temperature fluid Enter temperature of high- temperature fluid Temperature Slope calibration Start C...

12.1 Status LED states The status LED on the transmitter indicates whether or not alarms are active. If alarms areactive, view the alarm list to identify the alarms, then take appropriate action to correctthe alarm condition. Your transmitter has a status LED only if it has a display. If the transmi...

12.3 Flow measurement problems Flow measurement problems and recommended actions Table 12-3: Problem Possible causes Recommended actions Flow indication at noflow conditions orzero offset • Misaligned piping (especially in new in-stallations) • Open or leaking valve • Incorrect sensor zero • Verify ...

12.4 Density measurement problems Density measurement problems and recommended actions Table 12-4: Problem Possible causes Recommended actions Inaccurate densityreading • Problem with process fluid • Incorrect density calibration factors • Wiring problem • Incorrect flowmeter grounding • Slug flow •...

12.5 Temperature measurement problems Temperature measurement problems and recommended actions Table 12-5: Problem Possible causes Recommended actions Temperature readingsignificantly differentfrom process temper-ature • RTD failure • Wiring problem • Check junction box for moisture or verdi-gris. •...

12.6 Milliamp output problems Milliamp output problems and recommended actions Table 12-6: Problem Possible causes Recommended actions No mA output • Wiring problem • Circuit failure • Channel not configured for desired output • Check the power supply and power supplywiring. See Section 12.9 . • Che...

Milliamp output problems and recommended actions (continued) Table 12-6: Problem Possible causes Recommended actions mA output consis-tently out of range • Incorrect process variable or units assignedto output • Fault condition if fault action is set to up-scale or downscale • LRV and URV are not se...

Frequency output problems and recommended actions Table 12-7: Problem Possible causes Recommended actions No frequency output • Stopped totalizer • Process condition below cutoff • Fault condition if fault action is set to in-ternal zero or downscale • Slug flow • Flow in reverse direction from conf...

For more information on using sensor simulation using ProLink II, see Section 7.1 . 12.9 Check power supply wiring If the power supply wiring is damaged or improperly connected, the transmitter may notreceive enough power to operate properly. Prerequisites You will need the installation manual for y...

Prerequisites You will need the installation manual for your transmitter. Procedure 1. Before opening the wiring compartments, disconnect the power source. CAUTION! If the transmitter is in a hazardous area, wait five minutes after disconnecting thepower. 2. Verify that the transmitter is connected ...

c. At the transmitter, activate Select . d. Scroll to and select SET OFF . e. Verify the signal at the receiving device.f. At the transmitter, activate Select . Postrequisites • If the mA output reading was slightly off at the receiving device, you can correct thisdiscrepancy by trimming the output....

i. Click UnFix mA . 2. Test the frequency output(s). Note If the Weights & Measures application is enabled on the transmitter, it is not possible toperform a loop test of the frequency output, even when the transmitter is unsecured. a. Choose ProLink > Test > Fix Freq Out . b. Enter the fr...

f. Click UnFix . 12.12.4 Perform loop tests using the Field Communicator Tip Loop tests are not required. However, Micro Motion recommends performing a loop test for everyinput or output available on your transmitter. The inputs and outputs available on your transmittervary according to your purchas...

b. Read the frequency signal at the receiving device and compare it to the transmitter output. c. Choose End . 3. Test the discrete output(s). a. Press Service Tools > Simulate > Simulate Outputs > Discrete Output Test . b. Choose Off . c. Verify the signal at the receiving device.d. Press ...

12.14 Check the HART communication loop If you cannot establish or maintain HART communications, the HART loop may be wiredincorrectly. Prerequisites You will need: • A copy of your transmitter installation manual • A Field Communicator • Optional: the HART Application Guide , available at www.hartc...

Procedure 1. Set HART Address as appropriate for your HART network. The default address is 0. This is the recommended value unless the transmitter is in amultidrop network. 2. Set Loop Current Mode to Enabled . 12.16 Check HART burst mode HART burst mode can cause the transmitter to output unexpecte...

The Flow Direction parameter interacts with actual flow direction to affect flow values, flow totals and inventories, and output behavior. For the simplest operation, actual processflow should match the flow arrow that is on the side of the sensor case. Procedure 1. Verify the actual direction of pr...

12.26 Check the drive gain Excessive or erratic drive gain may indicate any of a variety of process conditions, sensorproblems, or configuration problems. To know whether your drive gain is excessive or erratic, you must collect drive gain dataduring the problem condition and compare it to drive gai...

Possible causes and recommended actions for erratic drive gain (continued) Table 12-9: Possible cause Recommended actions Polarity of pick-off reversed or polarity of drive reversed Contact Micro Motion. Slug flow Check for slug flow. See Section 12.25 . Foreign material caught in flow tubes • Purge...

Possible causes and recommended actions for low pickoff voltage (continued) Table 12-10: Possible cause Recommended actions No tube vibration in sensor • Check for plugging. • Ensure sensor is free to vibrate (no mechanical binding). • Verify wiring. • Test coils at sensor. See Section 12.28.1 . Moi...

12.28.1 Check the sensor coils Checking the sensor coils can identify electrical shorts. Restriction This procedure applies only to 9-wire remote-mount transmitters and remote transmitters withremote core processors.. Procedure 1. Disconnect power to the transmitter. CAUTION! If the transmitter is i...

a. Leave the terminal blocks disconnected.b. Remove the lid of the junction box.c. Testing one terminal at a time, place a DMM lead on the terminal and the other lead on the sensor case. With the DMM set to its highest range, there should be infinite resistance oneach lead. If there is any resistanc...

a. Remove the core processor lid. The core processor is intrinsically safe and can be opened in all environments. b. Check the state of the core processor LED. 3. If you have an integral installation: a. Loosen the four cap screws that fasten the transmitter to the base. Integral installation compon...

9-wire remote installation components Figure 12-2: Transmitter Core processor 4 x cap screws (4 mm) End-cap b. Inside the core processor housing, loosen the three screws that hold the core processor mounting plate in place. Do not remove the screws. c. Rotate the mounting plate so that the screws ar...

3. Tighten the screws, torquing to 6 to 8 in-lbs (0.7 to 0.9 N-m).4. Replace the end-cap. Important When reassembling the meter components, be sure to grease all O-rings. 12.29.1 Core processor LED states Standard core processor LED states Table 12-13: LED state Description Recommended actions 1 fla...

Enhanced core processor LED states (continued) Table 12-14: LED state Description Recommended action Solid red High-severity alarm Check alarm status. Flashing red (80% on, 20% off) Tubes not full • If alarm A105 (slug flow) is active, refer to therecommended actions for that alarm. • If alarm A033 ...

Appendix AUsing the transmitter display Topics covered in this appendix: • Components of the transmitter interface • Use the optical switches • Access and use the display menu system • Display codes for process variables • Codes and abbreviations used in display menus • Menu maps for the transmitter...

Transmitter interface Figure A-1: A B C D E F G H A. Status LED B. Display (LCD panel) C. Process variable D. Scroll optical switch E. Optical switch indicator F. Select optical switch G. Unit of measure for process variable H. Current value of process variable A.2 Use the optical switches Use the o...

Optical switch indicator and optical switch states Table A-1: Optical switch indicator State of optical switches Solid red One optical switch is activated. Flashing red Both optical switches are activated. A.3 Access and use the display menu system The display menu system is used to perform various ...

Tip If you do not know the correct value for Off-Line Password , wait 30 seconds. The password screen will time out automatically and you will be returned to the previous screen. 4. If Scroll flashes on the display, activate the Scroll optical switch, then the Select optical switch, and then the Scr...

• To exit the menu without saving the displayed value to transmitter memory,activate Scroll and Select simultaneously and hold until the display changes. - If the displayed value is the same as the value in transmitter memory, you will bereturned to the previous screen. - If the displayed value is n...

b. Activate Scroll until the desired character is displayed. c. Activate Select to move the cursor one digit to the left. d. Activate Scroll until the desired character is displayed. e. Activate Select to move the cursor one digit to the left. f. Activate Scroll until the desired character is displa...

A.5 Codes and abbreviations used in display menus Codes and abbreviations used in display menus Table A-3: Code or abbrevi-ation Definition Comment or reference ACK ALARM Acknowledge alarm ACK ALL Acknowledge all alarms ACT Action ADDR Address AO 1 SRC Fixed to the process variable assigned to the p...

A.6 Menu maps for the transmitter display Offline menu – top level Figure A-2: Scroll and Select simultaneously for 4 seconds VER OFF-LINE MAINT Select SEE ALARM Scroll Scroll EXIT CONFG Scroll SIM ZERO SENSOR VERFY* Scroll Scroll Scroll Scroll EXIT *This option is displayed only if the transmitter ...

Offline menu – version information Figure A-3: Scroll and Select simultaneously for 4 seconds VER Yes Version info Scroll Select Yes CEQ/ETO info* Scroll CUSTODY XFER* Scroll Yes SENSOR VERFY* Scroll Scroll EXIT OFF-LINE MAINT Select Scroll ED/API info* Scroll *The option is displayed only if the co...

Offline menu – configuration: units and I/O Figure A-4: OFF-LINE MAINT Scroll and Select simultaneously for 4 seconds Scroll Select Select Scroll CONFG MASS UNITS VOL/GSV DENS TEMP Select Scroll Scroll Scroll AO 1 SRC AO 1 4 MA AO 120 MA Scroll Scroll EXIT Scroll Scroll PRESS FO FO SRC FO FREQ Selec...

Offline menu – alarms Figure A-6: SEE ALARM Scroll and Select simultaneously for 4 seconds ACK ALL* Yes EXIT Select No Alarm code Scroll ACK Yes Select No Active/ unacknowledged alarms? No Yes Select NO ALARM EXIT Scroll Scroll Select Scroll Scroll Select *This screen is displayed only if the ACK AL...

Offline menu – meter verification test Figure A-9: OUTPUTS ARE YOU SURE/YES? . . . . . . . . . . . . . . . x% PASS VERFY ABORTED VERFY CAUTION VERFY Fail Abort RERUN/YES? Yes No Correct condition RUN VERFY CONTINUE MEASR FAULT LAST VALUE Select Scroll Scroll Scroll Select Scroll RESULTS VIEW/YES? Se...

Offline menu – meter verification results Figure A-10: RESULTS READ Select xx L STF% RUNCOUNT x Select xx HOURS Select PASS Select xx R STF% Select RESULTS MORE? Select Scroll To Run Verfy Pass Select Scroll Result type Fail Abort xx HOURS Select CAUTION xx L STF% xx R STF% Select Select xx HOURS Ab...

Offline menu – totalizers and inventories Figure A-11: RESET (3) Select Scroll STOP/START (2) RESET YES? Process variable display STOP/START YES? Scroll Mass total Volume total Scroll Select Yes No Select Scroll EXIT Select Yes No Select Scroll Scroll E1--SP (1) E2--SP (1) Scroll Scroll Scroll (1) T...

Offline menu – Zero Figure A-13: …………………. OFF-LINE MAINT Scroll and Select simultaneously for 4 seconds Scroll Select Select CAL ZERO Troubleshoot ZERO/YES? CAL PASS CAL FAIL RESTORE ZERO RESTORE ZERO/YES? Current zero display Factory zero display Select Select Yes No EXIT Scroll Select Scroll Scrol...

Appendix BUsing ProLink II with the transmitter Topics covered in this appendix: • Basic information about ProLink II • Connect with ProLink II • Menu maps for ProLink II B.1 Basic information about ProLink II ProLink II is a software tool available from Micro Motion. It runs on a Windows platform a...

ProLink II messages As you use ProLink II with a Micro Motion transmitter, you will see a number of messagesand notes. This manual does not document all of these messages and notes. Important The user is responsible for responding to messages and notes and complying with all safetymessages. B.2 Conn...

B.2.2 Make a service port connection CAUTION! If the transmitter is in a hazardous area, do not use a service port connection. Service portconnections require opening the wiring compartment, and opening the wiring compartmentwhile the transmitter is powered up could cause an explosion. To connect to...

Connection to service port Figure B-1: A C D E B A. PCB. Signal converterC. Service port terminal 7 (RS-485/A)D. Service port terminal 8 (RS-485/B)E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also sup...

Connection to transmitter terminals Figure B-2: A C D B A. PCB. Signal converterC. 250–600 Ω resistance D. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 3. To connect from a point in the l...

Connection over local loop Figure B-3: A C D E R1 R3 R2 B A. PCB. Signal converterC. Any combination of resistors R1, R2, and R3 as necessary to meet HART communication resistance requirementsD. DCS or PLCE. Transmitter, with wiring compartment and power supply compartment opened Note This figure sh...

Connection over multidrop network Figure B-4: B A C D A. Signal converterB. 250–600 Ω resistance C. Devices on the networkD. Master device 5. Start ProLink II. 6. Choose Connection > Connect to Device . 7. Set Protocol to HART Bell 202 . Tip HART/Bell 202 connections use standard connection param...

Connection over network Figure B-6: A C E D B A. PCB. Signal converterC. 120- Ω , 1/2-watt resistors at both ends of the segment, if necessary D. DCS or PLCE. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are...

Connection over network Figure B-8: A C E D B A. PCB. Signal converterC. 120- Ω , 1/2-watt resistors at both ends of the segment, if necessary D. DCS or PLCE. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are...

Need help? If an error message appears: • Verify the Modbus address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical connection between the PC and the transmitter. • Increase or decrease resistance. • For long-distance communication, or if noise from an...

Configuration menu Figure B-11: Flow • Flow Direction • Flow Damp • Flow Cal • Mass Flow Cutoff • Mass Flow units • Mass Factor • Dens Factor • Vol Factor • Flow Switch Variable • Flow Switch Setpoint • Flow Switch Hysteresis • Vol Flow Cutoff • Vol Flow Units • Vol Flow Type • Std Gas Vol Flow Cuto...

Appendix CUsing ProLink III with the transmitter Topics covered in this appendix: • Basic information about ProLink III • Connect with ProLink III • Menu maps for ProLink III C.1 Basic information about ProLink III ProLink III is a configuration and service tool available from Micro Motion. It runs ...

ProLink III messages As you use ProLink III with a Micro Motion transmitter, you will see a number of messagesand notes. This manual does not document all of these messages and notes. Important The user is responsible for responding to messages and notes and complying with all safetymessages. C.2 Co...

Need help? If an error message appears: • Verify the Modbus address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical connection between the PC and the transmitter. • Increase or decrease resistance. • For long-distance communication, or if noise from an...

Configuration: Process Measurement (with Petroleum Measurement) Figure C-12: Configuration: I/O Figure C-13: Using ProLink III with the transmitter Configuration and Use Manual 313

Diagnostics: Testing Figure C-22: Diagnostics: Meter Verification Figure C-23: Using ProLink III with the transmitter 318 Micro Motion ® Model 2700 Transmitters with Analog Outputs

Device Tools: Trending Figure C-24: Using ProLink III with the transmitter Configuration and Use Manual 319

Appendix DUsing the Field Communicator with the transmitter Topics covered in this appendix: • Basic information about the Field Communicator • Connect with the Field Communicator • Menu maps for the Field Communicator D.1 Basic information about the Field Communicator The Field Communicator is a ha...

If Micro Motion is not listed, or you do not see the required device description, use the Field Communicator Easy Upgrade Utility to install the device description, or contactMicro Motion. Field Communicator menus and messages Many of the menus in this manual start with the On-Line menu. Ensure that...

Field Communicator connection to transmitter terminals Figure D-1: A B C A. Field CommunicatorB. 250–600 Ω resistance C. Transmitter, with wiring compartment and power supply compartment opened 2. To connect to a point in the local HART loop, attach the leads from theField Communicator to any point ...

Field Communicator connection to multidrop network Figure D-3: A B C D A. Field CommunicatorB. 250–600 Ω resistance C. Devices on the networkD. Master device 4. Turn on the Field Communicator and wait until the main menu is displayed. 5. If you are connecting across a multidrop network: a. Set the F...

Overview menu Figure D-5: Identification 1 Tag2 Model3 Xmtr Serial Num4 Sensor Serial Num5 Date6 Descriptor7 Message 1 Revisions 1 Universal2 Field Device3 DD Revision4 Transmitter Software5 CP Software6 ETO Number Mat. of Construction 1 Tube Wetted Mat.2 Tube Lining3 Sensor Flange Check Status 1 Re...

Configure menu Figure D-6: Manual Setup 1 Characterize2 Measurements3 Display4 Inputs/Outputs5 Info Parameters 2 1 Alert Setup 1 I/O Fault Actions2 Alert Severity3 Discrete Events4 CM Alerts On-Line Menu > 1 Configure Using the Field Communicator with the transmitter Configuration and Use Manual ...

Manual Setup menu Figure D-7: Characterize 1 Sensor Type2 Sensor Tag Parameters Measurements 1 Flow2 Density3 Temperature4 Update Rate5 LD Optimization6 Special Units7 External Pressure/Temperature8 Petroleum Measurement *9 GSV10 Conc Measure (CM) ** 1 2 Inputs/Outputs 1 Channels2 mA Output3 Frequen...

Manual Setup menu: Characterize Figure D-8: On-Line Menu > 2 Configure > 1 Manual Setup > 1 Characterize 2 1 2 1 Sensor Type Straight Tube Curved Tube Density Parameters 1 D12 D23 DT4 DTG5 K16 K27 FD8 DFQ19 DFQ2 Flow Parameters 1 Flow FCF2 FTG3 FFQ Sensor Tag Parameters 1 Flow Parameters2 D...

Manual Setup menu: Measurements Figure D-9: On-Line Menu > 2 Configure > 1 Manual Setup > 2 Measurements Flow 1 Flow Direction2 Flow Damping3 Mass Flow Unit4 Mass Flow Cutoff5 Volume Flow Unit *6 Volume Flow Cutoff *7 Mass Factor8 Volume Factor Density 1 Density Unit2 Density Damping3 Densi...

Manual Setup menu: Display Figure D-11: On-Line Menu > 2 Configure > 1 Manual Setup > 3 Display Language EnglishGermanFrenchSpanish Display Variable Menu Features 1 Totalizer Reset2 Start/Stop Totals3 Auto Scroll4 Scroll Time *5 Refresh Rate6 Status LED Blinking Offline Variable Menu Featur...

Alert Setup menu Figure D-14: On-Line Menu > 2 Configure > 2 Alert Setup I/O Fault Action 1 MAO Fault Action2 MAO Fault Level3 FO Fault Action4 FO Fault Level5 Comm Fault Action Alert Severity 1 Fault Timeout2 Set Alert Severity3 View Alert Severity Discrete Events 1 Discrete Event 12 Discrete...

Service Tools menu Figure D-15: On-Line Menu > 3 Service Tools Alerts 1 Refresh Alerts Alert NameAdditional Information Variables 1 Variable Summary2 Process Variables3 Mapped Variables4 External Variables5 Totalizer Control6 Variables (PM) *7 Variables (CM) **8 Outputs 1 2 Trends 1 Process Varia...

Service Tools menu: Variables Figure D-16: On-Line Menu > 3 Service Tools > 2 Variables Process Variables 1 Mass Flow Rate2 Volume Flow Rate *3 Density4 Temperature Mapped Variables 1 PV Mass Flow Rate2 SV Mass Flow Rate3 TV Mass Flow Rate4 QV Mass Flow Rate 1 3 5 Totalizer Control 1 All Total...

Service Tools menu: Maintenance Figure D-18: On-Line Menu > 3 Service Tools > 4 Maintenance Routine Maintenance 1 Trim mA Output2 Meter Verification * 1 Zero Calibration 1 Mass Flow Rate2 Volume Flow Rate3 Zero Time4 Zero Value5 Standard Deviation6 Perform Auto Zero7 Restore Factory Zero Densi...

Service Tools menu: Simulate Figure D-19: On-Line Menu > 3 Service Tools > 5 Simulate 1 Simulate Outputs 1 mA Output Loop Test2 Frequency Output Test/ Discrete Output Test * * Options vary depending on Channel settings. Simulate Sensor 1 Simulate Primary Purpose Variables2 Mass Flow Rate3 Dens...

Appendix EDefault values and ranges E.1 Default values and ranges The default values and ranges represent the typical factory transmitter configuration.Depending on how the transmitter was ordered, certain values may have been configuredat the factory and are not represented in the default values an...

Appendix FTransmitter components and installation wiring Topics covered in this appendix: • Installation types • Power supply terminals and ground • Input/output (I/O) wiring terminals F.1 Installation types Model 1700 and Model 2700 transmitters can be installed five different ways, only one ofwhic...

High-temperature flexible conduit installation Figure F-2: High-temperature flexible conduit installations use the same installationinstructions as 4-wire remote installations, except that the distance between thesensor and the electronics is limited by the length of the flexible conduit. • 4-wire r...

4-wire remote installation – stainless steel housing Figure F-4: Sensor Core processor Transmitter 4-wire cable • 9-wire remote – The transmitter and core processor are combined in a single unit that is installed remotely from the sensor. You need to mount the transmitter/coreprocessor assembly sepa...

9-wire remote installation type Figure F-5: Transmitter Junction box Sensor 9-wire cable • Remote core processor with remote sensor – A remote core process with remote sensor installation separates all three components – transmitter, core processor,and sensor – all of which are installed separately....

Remote core processor with remote sensor installation type Figure F-6: Core processor Transmitter 4-wire cable 9-wire cable Sensor Junction box F.2 Power supply terminals and ground Power supply wiring terminals Figure F-7: A B C A. Warning flap B. Equipment ground C. Power supply wiring terminals (...