Emerson MICRO - Manuals

Bristol Training GET THE MOST FROM YOUR BRISTOL BABCOCK INSTRUMENT OR SYSTEM • Avoid Delays and problems in getting your system on-line • Minimize installation, start-up and maintenance costs. • Make the most effective use of our hardware and software. • Know your system. As you know, a well-trained...

A Few Words About Bristol Inc. For over 100 years, Bristol ® has been providing innovative solutions for the measurement and control industry. Our product lines range from simple analog chart recorders, to sophisticated digital remote process controllers and flow computers, all the way to turnkey SC...

For technical questions regarding ACCOL products, OpenBSI Utilities , UOI and all other software except for Control Wave and OpenEnterprise products, call (860) 945-2286. For technical questions about Network 3000 hardware, call (860) 945-2502. You can e-mail the Application Support Group at: bsuppo...

PIP-ControlWaveLS 1 Table Of Contents PIP-ControlWaveLS Control Wave Loop Supply Part Numbers 400095-01-7, 721708-01-3 & 721708-02-1 TABLE OF CONTENTS Section Title Page # Section 1 – LOOP SUPPLY INTRODUCTION 1.1 GENERAL DESCRIPTION...................................................................

PIP-ControlWaveLS Page - 1 Section 1 LOOP SUPPLY INTRODUCTION 1.1 GENERAL DESCRIPTION Bristol’s Control Wave Loop Power Supply (herein referred to as the “ Loop Supply ” ), provides regulated and isolated 24Vdc power outputs that can be used to power field devices such as transmitters or non-isolate...

Page - 2 PIP-ControlWaveLS Figure 1 - Control Wave Loop Supply Board Views & Component Identification Diagram Table 1 - Input/Pass-through Power Connectors – TB1 & TB3 TB1 Pin # TB3 Pin # Signal Name Description Notes 1 3 VIN 9 to 30 +Vdc power Input or Non-fused Throughput 2 2 RET 9-30 Vdc ...

Page - 4 PIP-ControlWaveLS Section 2 LOOP SUPPLY INSTALLATION 2.1 LOOP SUPPLY MOUNTING Encapsulated Loop Supply Assemblies are provided with the printed circuit board (PCB) secured to a Power Supply Back Plate Bracket and protected by a Power Supply Board Cover. These units may be mounted directly t...

PIP-ControlWaveLS Page - 5 Figure 3 - Encapsulated ControlWave Loop Supply Mounting Diagram

Page - 6 PIP-ControlWaveLS 2.2 LOOP SUPPLY WIRING Loop Supply’s utilize Terminal Blocks that are equipped with compression-type terminals which accommodate a #16 AWG size wire. A connection is made by inserting the wire’s bared end (1/4” Max.) into the clamp beneath the screw and then tightening the...

PIP-ControlWaveLS Page - 7 Figure 4 - ControlWave MICRO & EFM Loop Supply to I/O Module Wiring

Page - 8 PIP-ControlWaveLS Figure 5 - Control Wave Express, ExpressPAC and GFC Loop Supply to Process I/O Board Wiring Diagrams Control Wave EFM – System Controller Module - Connector TB1 TB1-1 = +VIN (from loop Supply Connector TB3-3 = VIN) TB1-2 = -VIN (from loop Supply Connector TB3-2 = GND) Cont...

PIP-ControlWaveLS Page - 9 Control Wave ExpressPAC – CPU/System Controller Board - Connector TB1 TB1-3 = POWER IN+ (from loop Supply Connector TB3-3) TB1-4 = GND (from loop Supply Connector TB3-2) Control Wave GFC – CPU/System Controller Board - Connector TB1 TB1-3 = POWER IN+ (from loop Supply Conn...

Page - 10 PIP-ControlWaveLS Section 3 SPECIFICATIONS 3.1 OPERATING SPECIFICATIONS Function: Provides four isolated 24Vdc power output terminal pairs to power an RTU , a Transmitter and/or a number of non-isolated I/O (associated with a particular Control Wave RTU. Output Voltage : Electrically Isola...

Page - 12 PIP-ControlWaveLS Figure 6 - Loop Supply Dimensions Drawing

Product Information Package PIP-Control Wave LS July, 2006 ControlWave Loop Power Supply The information in this document is subject to change without notice. Every effort has been made to supply complete and accurate information. However, Bristol, Inc. assumes no responsibility for any errors that ...