Emerson Liebert APS- Manuals

4 Chapter 1 Installation Liebert APM Modular UPS User & Installation Manual 1.4.3 Clearances The UPS has no ventilation grilles at either side; therefore, no clearance is required at either side. To enable routine tightening of power terminations within the UPS, in addition to meeting any local ...

Chapter 1 Installation 5 Liebert APM Modular UPS User & Installation Manual Power module A amplified view Fixing holes DIP switch Ready switch A Figure 1-2 Installing power module Installation procedures of Optional output distribution modules Use the following procedures of install the output d...

6 Chapter 1 Installation Liebert APM Modular UPS User & Installation Manual Earth Leakage Any residual current detector (RCD) installed upstream of the UPS input supply must: z be sensitive to DC unidirectional pulses (Class A) in power distribution network z be insensitive to transient current ...

Chapter 1 Installation 7 Liebert APM Modular UPS User & Installation Manual 1. Protective earth cable: Follow the most direct route possible to connect the earth cable to the cabinet. The earth cable shall be sized in accordance with the AC supply fault rating, cable lengths and type of protecti...

8 Chapter 1 Installation Liebert APM Modular UPS User & Installation Manual at the rear of the UPS cabinet. Tighten the output neutral bar connections to 5Nm (M6 bolt). Ensure correct phase rotation. z In case output distribution modules are not installed, please connect the output cables betwee...

Chapter 1 Installation 9 Liebert APM Modular UPS User & Installation Manual Figure 1-5 Battery Cabinet Details Figure 1-6 Battery Connection 1.7 Control And Communications As shown in Figure 1-7, the bypass module provides dry contact ports (J5 ~ J10) and communication ports (RS232 port and SNMP...

Chapter 1 Installation 11 Liebert APM Modular UPS User & Installation Manual 1.7.2 BCB Port J6 is the battery circuit breaker (BCB) port. The port is shown in Figure 1-6 and described in Table 1-9. J6 OL GN D FB DRV 12V 12V 12V Figure 1-9 BCB port Table 1-6 BCB port description Position Name Des...

Chapter 1 Installation 13 Liebert APM Modular UPS User & Installation Manual 1.7.6 Other Communication Interface The RS232 port provides serial data and is intended for use by authorized commissioning and service personnel in UPS commissioning and service. Liebert APM UPS has facility of interna...

16 Chapter 2 Operation Liebert APM Modular UPS User & Installation Manual Chapter 2 Operation This chapter introduces the basic knowledge of UPS operation, including the operating theory, operation mode, battery management and battery protection of the UPS. Warning: hazardous mains and battery v...

Chapter 2 Operation 17 Liebert APM Modular UPS User & Installation Manual During normal operating conditions, the inverter output and bypass supply must be fully synchronized so as to achieve a clean (no-break) load transfer between the inverter output and static bypass line. The synchronization...

18 Chapter 2 Operation Liebert APM Modular UPS User & Installation Manual interruption is programmable but typically set to be less than 3/4 of an electrical cycle, for example, less than 15ms (50Hz) or less than 12.5ms (60Hz). 2.2.5 Maintenance Bypass Mode If UPS maintenance or repaired is need...

Chapter 2 Operation 19 Liebert APM Modular UPS User & Installation Manual 2.3.2 Advanced Function —— Battery Self-Test And Self-Service At periodic intervals 20% of the rated capacity of the battery will be discharged automatically. The minimum amount of load must exceed 20% of the nominal ratin...

20 Chapter 3 Operating Procedures Liebert APM Modular UPS User & Installation Manual Chapter 3 Operating Procedures This chapter provides detailed operating procedures of the UPS. All control keys and LED indication mentioned in these procedures are identified in Chapter 4 Operator Control And D...

22 Chapter 3 Operating Procedures Liebert APM Modular UPS User & Installation Manual Battery start button Figure 3-2 Location of battery start button 3.3 Procedures Of Transfer Between Operation Modes 3.3.1 Transfer From Normal Mode To Battery Mode Open the input switch to cut off the mains inpu...

Chapter 3 Operating Procedures 23 Liebert APM Modular UPS User & Installation Manual 3. Open the input switch and output switch. Caution 1. The load is not protected from normal supply aberrations when the UPS is operating in maintenance bypass mode. 2. After the UPS is transferred to maintenanc...

24 Chapter 3 Operating Procedures Liebert APM Modular UPS User & Installation Manual 3.8 Changing The Current Date And Time To change the system date and time, carry out the following procedures: 1. From the Output menu, press the F3 or F4 (left or right) key as needed to select the Settings men...

Chapter 4 Operator Control And Display Panel 25 Liebert APM Modular UPS User & Installation Manual Chapter 4 Operator Control And Display Panel This chapter expounds the functions and use of the components on the operator control and display panel of the UPS, and provides LCD display information...

Chapter 4 Operator Control And Display Panel 27 Liebert APM Modular UPS User & Installation Manual 4.1.4 LCD And Menu Keys The operator control and display panel provides an LCD and five menu keys (F1, F2, F3, F4, F5). The menu keys are described in Table 4-5. Table 4-5 Menu key description Func...

Chapter 4 Operator Control And Display Panel 29 Liebert APM Modular UPS User & Installation Manual 4.2.3 Default Screen During UPS operation, if there is no alarm within two minutes, the default screen will appear, as shown in Figure 4-5. After a short delay, the LCD backlight will turn off. Pre...

Chapter 4 Operator Control And Display Panel 31 Liebert APM Modular UPS User & Installation Manual Menu Item Explanation Battery maintenance test This test performs a partial discharge of the battery to obtain a rough estimate of the battery capacity. Load must be between 20% and 100% Battery ca...

Chapter 5 Service 35 Liebert APM Modular UPS User & Installation Manual Chapter 5 Service This chapter introduces the UPS service, including the service procedures of the power module, bypass module and output distribution module, and the replacement of air filter. 5.1 Replacement Procedures Of ...

36 Chapter 5 Service Liebert APM Modular UPS User & Installation Manual 6. After servicing the module, push the module (at least 10s after another) into the cabinet, and tighten the screws on both sides. 7. Close the UPS output switch and input switch in turn. Two minutes later, the bypass indic...

Chapter 6 Specifications 37 Liebert APM Modular UPS User & Installation Manual Chapter 6 Specifications The chapter provides the UPS specifications. 6.1 Conformity And Standards The UPS has been designed to conform to the European and international standards listed in Table 6-1. Table 6-1 Europe...

40 Chapter 6 Specifications Liebert APM Modular UPS User & Installation Manual 6.7 Electrical Characteristics (Bypass Mains Input) Table 6-7 Bypass mains input Rated power (kVA) Unit 30 ~ 150 Rated AC voltage 1 Vac 380/400/415, three-phase four-wire, sharing neutral with the rectifier input and ...

Appendix 1 BCB Model Selection And Connection 41 Liebert APM Modular UPS User & Installation Manual Appendix 1 BCB Model Selection And Connection Table 1 Selection reference table of BCB rated current and connection cable cross CSA Rated power (kVA) Unit 30 60 90 120 150 Max battery discharge cu...