Emerson HD8100BL - Manuals - manualsarea.com

Page 3 - C L AS S 1 L AS ER PR O D U C T; Th i s pro duc t c ont ai ns a l ow po w er Laser De vi c e.; Av o i d i ns t a l l i n g t h e u n i t i n l o c a t i o ns d es c ri b e d b e l o w :; CAUT IO N; I M PORTANT NOTES

2 WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. This device complies with part 15 of the FCC rules. Operation is subject to thecondition that this device does not cause harmful interference. C L AS S 1 L AS ER PR O D U C T CLASS 1 LASER PRODUCT APPAREIL Á LAS...

Page 4 - PREPARATI ON FOR USE; REMOVE THE TRANSIT CARD; OPEN; P O W E R S O U R C E S; In p u t : 1 2 0 V 6 0 H z A C

3 PREPARATI ON FOR USE REMOVE THE TRANSIT CARD This personal CD player is shipped with a dummy CD ‘transit card ‘ inside the CD compartment. The purpose of this card is to prevent the laser from moving during shipment of the product. This card must be removed before using the CD player. Slide the OP...

Page 5 - INSTAL L I N G T H E B ATTERIES; Note; REPLACING THE BATTERIES

4 INSTAL L I N G T H E B ATTERIES Note : The battery compartment is located inside the CD compartment. 1.) Slide the OPEN switch to the right to open the CD door. If you have not already done so, remove the dummy CD ‘transit card’ and discard it. 2.) Press the battery door locking tab in the directi...

Page 6 - CONNECTING THE OPTIONAL AC ADAPTER (NOT INCLUDED); ) Connect the small female plug of the optional AC adapter to the “

5 CONNECTING THE OPTIONAL AC ADAPTER (NOT INCLUDED) 1.) Connect the small female plug of the optional AC adapter to the “ DC IN 4.5 V ” jack on the right side of the CD player. 2.) Connect the adapter housing to your 120V 60Hz AC outlet. Notes: • Never connect or disconnect the adapter from the AC o...

Page 7 - CONNECTING THE STEREO HEADPHONES; headphone jack on the left side of the cabinet.

6 CONNECTING THE STEREO HEADPHONES Connect the plug of the supplied stereo headphones to the green-colored headphone jack on the left side of the cabinet. NOTE : Make sure the headphone plug is inserted into the headphone jack as far as it will go. If the plug is not fully inserted, you may only hea...

Page 8 - LOCATI ON OF CONTROLS AND INDI CATORS

7 1.) OPEN Switch – Slide to the right to unlock and open the CD door.. 2.) VOLUME Control – Raises or lowers the volume. 3.) PHONES Jack – Connect stereo headphones, included, to this jack. 4.) HOLD Switch (Bottom Cabinet). 5.) PROG (Program) Button. 6.) PLAY/PAUSE Button. 7.) SKIP REV Button. 8.) ...

Page 9 - LCD DI SPLAY I NDI CATORS

8 1.) Track Number Display. 2.) PROG (Program) Indicator – Appears when programming tracks or playing programmed tracks. 3.) SHUFF (Shuffle) Indicator – Appears when Random playback mode is selected. 4.) INTRO Indicator – Appears when Intro playback mode is selected. 5.) HOLD Indicator – Appears whe...

Page 10 - OPERATI NG I NSTRUCTIONS; SPECIAL FUNCTIONS; H O L D S w i t c h

9 OPERATI NG I NSTRUCTIONS SPECIAL FUNCTIONS H O L D S w i t c h The HOLD switch on the bottom of the cabinet must be in the ‘Off’ (left) position to start the CD player. If you plan to carry the CD player in a handbag, briefcase, school bag, back pack, etc, slide the HOLD switch to the ‘On’ (right)...

Page 11 - ESP; not subject to bumps and shakes.

10 Electronic Skip Protection (ESP) This CD player includes an Electronic Skip Protection circuit that continuously stores 60 seconds of CD music in an electronic memory. If the player is bumped or shaken you will not hear any skipping because the player is reading from the memory, not directly from...

Page 12 - NORMAL CD PLAYBACK; • Make sure you have installed the batteries.; This CD player can play normal CDs plus CD Recordable (CD-R) and CD

11 NORMAL CD PLAYBACK • Make sure you have installed the batteries. • Make sure the HOLD switch is set to the ‘Off’ (left) position. • Make sure to set the VOLUME control to a low setting before you put on the headphones. I M P O R TANT: This CD player can play normal CDs plus CD Recordable (CD-R) a...

Page 13 - PAUSE CONTROL

12 6.) Playback will continue until the end of the disc, then the player will stop automatically and the display will again show the total tracks and playing time on the disc. After approximately 30 seconds the power switches ‘O f f ’ automatically to conserve the batteries and the display goes blan...

Page 14 - PLAY MODE BUTTON; ALL; ( R e p e a t A l l T r a c k s ); INTRO

13 PLAY MODE BUTTON Pressing the MODE button during playback cycles the player through the following four special playback modes: (Repeat 1 Track) ALL ( R e p e a t A l l T r a c k s ) INTRO S H U F F ( S h u f f l e ) P l a y b a c k . REPEAT PLAYBACK The player can be programmed to continuously re...

Page 15 - I N T R O ( I n t r o S c a n ) P L AYBACK

14 I N T R O ( I n t r o S c a n ) P L AYBACK The Intro Scan feature plays only the first 10 seconds of each track on the disc. This feature is useful when you are trying to find a particular song but you cannot remember the title. 1.) Load your disc in the player as usual and press the PLAY/PAUSE b...

Page 16 - PROGRAMMED PLAYBACK; You can program a disc either during playback or in Stop mode.

15 PROGRAMMED PLAYBACK You can program up to 20 tracks on a disc to play in any desired order. NOTE: You can program a disc either during playback or in Stop mode. 1.) Press the PROG button once. The PROG indicator and the Program Number ‘ 01 ’ appear, and the track number ‘ 00 ’ flashes. 2.) Press ...

Page 17 - NOTE; CARE AND M AINTENANCE

16 CL EAN I N G THE CABI N ET W ipe with a soft cloth. If the cabinet is very dirty, dampen the cloth with a weak solution of neutral detergent and water, and then wipe clean. CL EAN I N G THE LE NS A dirty lens will cause sound skipping and, if the lens is very dirty, the CD may not work. Open the ...

Page 18 - L IM IT ED WAR RA NT Y; of your proof of purchase. Send your unit to:; Consumer Affairs Dept.; SERVICE

17 L IM IT ED WAR RA NT Y Emerson Radio Corp. warrants manufacturing defects in original material, including original parts and workmanship, under normal use and conditions, for a period of ninety (90) days from the date of original purchase in the U.S. With your dated proof of purchase, we will pro...