Emerson EWC1902- Manuals

1-2-1 SFTY_2 IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electricalcodes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equallyimportant to implement the fo...

1-2-3 SFTY_2 Precautions during Servicing A. Parts identified by the ( # ) symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assembliesare specified for conformance with regulations ap-plying to spurious radiation. These must also bere...

1-2-4 SFTY_2 Safety Check after Servicing Examine the area surrounding the repaired locationfor damage or deterioration. Observe that screws,parts and wires have been returned to original posi-tions. Afterwards, perform the following tests and con-firm the specified values in order to verify complia...

1-3-1 SFTY_5 STANDARD NOTES FOR SERVICING Circuit Board Indications 1. The output pin of the 3 pin Regulator ICs is indi- cated as shown: 2. For other ICs, pin 1 and every 5th pin is indicated as shown: 3. The 1st pin of every pin connector are indicated as shown: Instructions for Connectors 1. When...

1-3-2 SFTY_5 Notes: a. Do not attempt to lift the component off the board until the component is completely disconnectedfrom the board by the twisting action. b. Take care not to break the copper foil on the printed board 3. Installing the leadless component a. Presolder the contact points of the ci...

1-3-3 SFTY_5 Fig. S-1-1 Fig. S-1-2 Hot-airFlat Pack-ICDesolderingMachine CBA MaskingTape Tweezers Flat Pack-IC Fig. S-1-3 Flat Pack-IC Desoldering Braid Soldering Iron Fig. S-1-4 Fine TipSoldering Iron Sharp Pin Fig. S-1-5 To Solid Mounting Point Hot Air Blower Iron Wire Soldering Iron or Fig. S-1-6...

1-3-4 SFTY_5 Instructions for Handling Semiconductors Electrostatic breakdown of the semiconductors mayoccur due to a potential difference caused by electro-static charge during unpacking or repair work. Ground for Human Body Be sure to wear a grounding band (1M Ω ) that is prop- erly grounded to re...

1-4-1 Z11PFS PREPARATION FOR SERVICING How to Enter the Service Mode Caution: 1 1. Optical sensors system are used for Tape Start and End Sensor on this equipment. Read this pagecarefully and prepare as described on this pagebefore starting to service; otherwise, the unit mayoperate unexpectedly. Pr...

1-5-1 T7300IB NOTE: We do not recommend the use of universal remote controls. Not all of the functions may be controlled witha universal remote control.If you decide to use a universal remote control with this unit, please be aware that the code number givenmay not operate this unit. In this case, p...

1-6-1 T7300DC CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart This flowchart indicates the disassembly steps for thecabinet parts, and the CBA in order to gain access toitem(s) to be serviced. When reassembling, follow thesteps in reverse order. Bend, route and dress thecables as they were...

1-7-1 T7300EA ELECTRICAL ADJUSTMENT INSTRUCTIONS General Note: "CBA" is abbreviation for "Circuit Board Assembly." NOTE: Electrical adjustments are required after replacingcircuit components and certain mechanical parts.It is important to perform these adjustments onlyafter all repai...

1-7-3 T7300EA 4-3. Y DL Time Adjustment Purpose: To get minimum leakage of the color signal carrier. Symptom of Misadjustment: If Y DL Time Adjust- ment is incorrect, stripes will appear on the screen. 1. Enter the Service mode. (See page 1-4-1.) 2. Press "0" button on the remote control uni...

1-7-5 T7300EA 9. Sub-Brightness Adjustment Purpose: To get proper brightness. Symptom of Misadjustment: If Sub-Brightness is incorrect, proper brightness cannot be obtained byadjusting the Brightness Control. Note: SYMPTE Setup level --- 7 IRE 1. Enter the Service Mode. (See page 1-4-1.) Then input ...

1-7-6 T7300EA The following 2 adjustments normally are notattempted in the field. They should be doneonly when replacing the CRT then adjust as apreparation. 13.Purity Adjustment Purpose: To obtain pure color. Symptom of Misadjustment: If Color Purity Adjust- ment is incorrect, large areas of color ...

CONTROLHEAD CL402 AC HEAD ASSEMBLY MAIN CBA KEY 1 RF-SW ST-SENS. T-REEL KEY 0 DV-SYNC C-SYNC C-SYNC V-ENV REMOTE CTL(+) RESET ROTA D-REC-H D-REC-H REC-SAFETY A-MUTE SCL SDA A-MUTE CTL(-) RF-SW DV-SYNC V-ENV ROTA END-SENS. IC201(SERVO/SYSTEM CONTROL) 14 94 95 9 7 80 34 18 15 10 13 74 33 44 65 72 6 5 ...

R L LUMINANCE SIGNAL PROCESS MAIN CBA Video Block Diagram VIDEO (L) HEAD VIDEO (R) HEAD 1-8-3 1-8-4 T7300BLV (DECK ASSEMBLY) V(L) V-COM V(R) CL401 3 2 1 Q401 JK701REAR V-IN J188 V-OUT V-AGC TUNER LINE R P R P SYNC SEPA FBC Y/C MIX CCD 1H DELAY R P DOC YNR Y/C COMB CHROMINANCE SIGNAL PROCESS IC401 VI...

Audio Block Diagram BLOCK DIAGRAM FOR SECTION 2 (DECK MECHANISM) MAIN CBA PB-AUDIO SIGNAL REC-AUDIO SIGNAL 1-8-5 JK702A-IN 48 26 27 53 IC301 IC401 Mode : SP/REC T7300BLA 1-8-6 BIASOSC Q872 P-ON+5V P-ON+5V Q871 Q873 Q874 Q875 (AUDIO PROCESS) 7 1 IC801 (AMP) SP 1 SP-GND 2 JK801EARPHONE JACK SP801SPEAK...

T7300BLC 1-8-7 1-8-8 X3013.58MHz CL504 4.5MHzTRAP CF302 4.5MHzBPF CF301 SAWFILTER SF001 IC301 VIDEO/AUDIO/CHROMA/DEFLECTION/IF TU001 IF AGC J191 RF AGC-OUT SDA SCL FSC 1 11 5 4 8 IC201(SYSTEM CONTROL/OSD) V-SYNC H-SYNC OSD-R OSD-G OSD-B 59 58 60 62 63 64 OSD-BLK TU AUDIO TO AUDIO BLOCK TU VIDEO TO V...

Power Supply Block Diagram 5 4 2 1 16 15 14 13 12 11 LINEFILTER BRIDGERECTIFIER T601 IC601 ERRORVOLTAGE DET W601 F6014A/125V L601 D603 - D606 T7300BLP SWITCHING Q604 VR601 DEGAUSSINGCOIL CN601 Q601 +B ADJ. FEEDBACK LIMITER Q602 PS601 4 1 3 2 HOT COLD 1-8-12 1-8 -11 Q606 Q605 Q607 DG601 AL+33V P-ON+5...

1-8-13 T5300MTI MECHANICAL TROUBLE INDICATOR 1, Each Malfunction Indication If the MONITOR is turned ON right after the Mechani-cal Malfunction occurs or POWER SAFETY/X-RAY isturned ON, display the following character to showMalfunction after the EJECT display. Example: If REEL Malfunction 2, Each M...

1-8-14 T5300MTI Mechanical Malfunction determination 1) REEL Malfunction detection Countermeasure for REEL and CAPSTAN motorrotation malfunction (Except CASSETTE LOAD-ING function) After the Malfunction detection with REEL/CAP-STAN sensor, the unit shall switch over to STOP(B) and be REEL Mechanical...

1-8-15 T5300TR1 Check Fuse (F601) is blown out or not. If fuse is blown out, do repair method #1 Check whether the primary rectifying DC of the Switching power supply has an output.(Reading should be about 168V. Voltage of the 105V line higher than normal? The transformer of the power supply makes a...

1-9-1 SC_1 (Top View) (Bottom View) (Bottom View) Electrolytic Capacitor + Transistor or Digital Transistor NPN Transistor PNP Transistor NPN Digital Transistor PNP DigitalTransistor (Top View) (Top View) E C B E C B Digital Transistor CBA Symbols Schematic Diagram Symbols E C B (Top View) (Top View...

A1 A2 A3 A4 A5 B1 B2 B3 B4 B5 C1 C2 C3 C4 C5 D1 D2 D3 D4 D5 E1 E2 E3 E4 E5 F1 F2 F3 F4 F5 G1 G2 G3 G4 G5 1-9-3 1-9-4 1-9-5 T7300SCM1 Main 1/4 Schematic Diagram MAIN 1/4 Ref No. Position IC201 D-3 IC202 F-4 Q205 C-1 Q206 F-4 J116 D-5 CL201 G-2 CONNECTORS TEST POINTS ICS TRANSISTORS

H1 H2 H3 H4 I1 I2 I3 I4 J1 J2 J3 J4 K1 K2 K3 K4 L1 L2 L3 L4 H5 I5 J5 K5 L5 M1 M3 M4 M5 N1 N2 N3 N4 N5 M2 PB Audio Signal PB Video Signal REC Audio Signal REC Video Signal 1-9-6 1-9-7 1-9-8 T7300SCM2 Main 2/4 Schematic Diagram MAIN 2/4 Ref No. Position IC401 I-2 IC801 M-4 Q401 K-2 Q402 L-4 Q491 L-2 Q...

O1 O2 O3 O4 P1 P2 P3 P4 Q1 Q2 Q3 Q4 R1 R2 R3 R4 S1 S2 S3 S4 O5 P5 Q5 R5 S5 T1 T3 T4 T5 U1 U2 U3 U4 U5 T2 PB Audio Signal PB Video Signal REC Audio Signal REC Video Signal 1-9-9 1-9-10 1-9-11 T7300SCM3 Main 3/4 Schematic Diagram MAIN 3/4 Ref No. Position IC301 R-2 Q301 R-5 Q302 Q-3 J191 Q-3 J233 T-2 ...

V1 V2 V3 V4 W1 W2 W3 W4 X1 X2 X3 X4 Y1 Y2 Y3 Y4 Z1 Z2 Z3 Z4 V5 W5 X5 Y5 Z5 AA5 AA4 AA3 AA2 AA1 BB5 BB4 BB3 BB2 BB1 PB Video Signal REC Video Signal 1-9-12 1-9-13 1-9-14 T7300SCM4 Main 4/4 Schematic Diagram NOTE : THE VOLTAGE FOR PARTS IN HOT CIRCUIT IS MEASURED USING HOT GND AS A COMMON TERMINAL. CA...

A-OUT J187 WF8 V-OUT J188 WF5 PB-C-MONI J189 WF6 RF-SW J190 WF1 RF AGC-OUT J191 CTL J116 WF3 +B ADJ VR601 + B J192 R583 (H Adjustment) GND J213 B-OUT J233 1-9-15 1-9-16 1-9-17 BT5300F01012 Main CBA Top View CAUTION !Fixed voltage power supply circuit is used in this unit.If Main Fuse (F601) is blown...

Main CBA Bottom View WF11 PIN 11OF IC301 WF10 PIN 20OF IC301 PIN 48OF IC301 PIN 7OF IC401 WF2 PIN 61OF IC401 WF4 PIN 42OF IC401 WF17 PIN 58OF IC201 WF18 PIN 59OF IC201 WF12 Q571Collector WF13 PIN 5OF CN571 1-9-18 1-9-19 1-9-20 CAUTION !Fixed voltage power supply circuit is used in this unit.If Main ...

Z11WF 1-10-1 1-10-2 WAVEFORMS WF2 MAIN 2/4 SCHEMATIC DIAGRAM IC401 PIN 61 WF1 MAIN 2/4 SCHEMATIC DIAGRAM J190 RF-SW Upper: WF6 Lower: WF1MAIN 2/4 SCHEMATIC DIAGRAM J189 PB-C-MONI WF5 MAIN 2/4 SCHEMATIC DIAGRAM J188 V-OUT WF4 MAIN 2/4 SCHEMATIC DIAGRAM IC401 PIN 42 WF9 MAIN 2/4 SCHEMATIC DIAGRAM IC40...

FULL ERASE HEAD WIRING DIAGRAM FOR SECTION 2 (DECK MECHANISM) WIRING DIAGRAM 3 2 1 HEATER CRT CBABT5300F01012 FOCUS SCREEN GND D.Y. HD VD CL403 CL501A MAIN CBABT5300F01012 HEA TER GND 1 2 3 CL501B CL504 CN501 1 2 CN601 W601 T571FBT CRT BLUE GREEN RED GND 4 3 2 1 1 2 3 4 5 CN571 1 3 CL504B BULE GREEN...

1-12-1 T5300TI SYSTEM CONTROL TIMING CHARTS Chart 1 1. EJECT (POWER OFF) -> CASSETTE IN (POWER ON) -> ST OP(B) -> ST OP(A) -> PLA Y -> RS -> FS -> PLA Y -> STILL -> PLA Y -> ST OP(A) EJECT CASS.LOAD ST-S,/END-S "OFF" PLAY REW FF PLAY PLAY PAUSE STOP/EJECT 0.2S S...

1-12-2 T5300TI Chart 2 ST-S,/END-S "ON" REC REW FF STOP/EJECT 1.0S 0.5S 0.2S 0.5S 0.2S 0.5S 0.5S 0.5S 0.2S 0.2S 0.2S 1.5S 2.5S Short REV 1.0S 0.2S LD-FWD LD-FWD STOP(A) STOP(A) STOP(A) CASS. UNLD EJECT STOP(A) LD-REV LD-REV LD-REV LD-REV LD-FWD LD-FWD LD-FWD LD-FWD LD-FWD LD-FWD LD-FWD REC P...

1-13-1 Z11PIN IC PIN FUNCTION DESCRIPTIONS IC 201 (TV/VCR Micro Computer) “H” ≥ 4.5V, “L” ≤ 1.0V Pin No. IN/ OUT Signal Name Function 1 IN LD-SW Loading Switch Input 2 IN P-SAFETY 1 Power Supply Failure Detection 1 3 IN P-SAFETY 2 Power Supply Failure Detection 2 4 IN P-SAFETY 3 Power Supply Failure...

1-14-1 T7300LE S: SouceD: DrainG: Gate S D G 2SC1627Y-TPE22SA950(Y,O)KTA1271(Y)2SC2482 TPE62SC3468(E,D)-AEKTC32072SA1175(F)KTA1267(GR)KTC3198(GR) BN1F4M-TKTC3199(GR)2SC2785(J,H,F)KTA1266(GR)2SA1015-GR(TPE2) E C B B C E 2SD2627LS-FEC-YB11TT2084LS-YB11 E: EmitterC: CollectorB: Base E C PT204-6B-12MID-...

2-1-1 U25MEN STANDARD MAINTENANCE Service Schedule of Components Notes: 1.Clean all parts for the tape transport (Upper Drum with Video Head / Pinch Roller / Audio Control Head / Full Erase Head) using 90% lsopropyl Alcohol. 2.After cleaning the parts, do all DECK ADJUSTMENTS. 3.For the reference nu...

2-1-2 U25MEN Cleaning Cleaning of Video Head Clean the head with a head cleaning stick or chamoiscloth. Procedure 1.Remove the top cabinet. 2.Put on a glove (thin type) to avoid touching the upper and lower drum with your bare hand. 3.Put a few drops of 90% Isopropyl alcohol on the head cleaning sti...

2-2-1 U25NFIX J-1-1, J-1-2 J-2 J-3 J-5 J-4 SERVICE FIXTURE AND TOOLS Ref. No. Name Part No. Adjustment J-1-1 Alignment Tape FL8A Head Adjustment of Audio Control Head J-1-2 Alignment Tape FL8N(2Head only)FL8NW(4Head only) Azimuth and X Value Adjustment of Audio Control Head / Adjustment of Envelope ...

2-3-1 Z11MA MECHANICAL ALIGNMENT PROCEDURES Explanation of alignment for the tape to correctly runstarts on the next page. Refer to the information belowon this page if a tape gets stuck, for example, in themechanism due to some electrical trouble of the unit. Service Information A. Method for Manua...

2-3-2 Z11MA Adjust the X Value for maximum envelope.(pg. 2-3-3) (Use Alignment Tape.) Check to see that the tape is not creasingand that there is no slack on the supplyand take-up side Guide Rollers.(Use a blank tape.) Adjust the height of the Guide Rollers(Supply side and take-up side).(Use a blank...

2-3-3 Z11MA 1-A. Preliminary/Final Checking and Alignment of Tape Path Purpose: To make sure that the tape path is well stabilized. Symptom of Misalignment: If the tape path is unstable, the tape will be damaged. Note: Do not use an Alignment Tape for this proce- dure. If the unit is not correctly a...

2-3-4 Z11MA 6. Press CH DOWN button on the unit until the CTL waveform has shifted from its original position (notthe position achieved in step 5, but the position ofCTL waveform in step 4) by approximately -2msec.Make sure that the envelope is simply attenuated(shrinks in height) once CTL waveform ...

2-4-9 U25NAPM ALIGNMENT PROCEDURES OF MECHANISM The following procedures describe how to align theindividual gears and levers that make up the tapeloading/unloading mechanism. Since informationabout the state of the mechanism is provided to theSystem Control Circuit only through the Mode Switch,it i...

EXPLODED VIEWS Cabinet 3-1-1 3-1-2 T7300CEX V501-1 L551 Details for L551 and surrounding parts SHINWHA TAPE SGT-730(WHITE) SHINWHA TAPE SGT-730(BLACK) TB22 See Electrical Parts List for parts with this mark. V501-3 V501-2 L1 L1 L1 L1 B5 B5 A3 A2 A1-1 A1-4 A1-2 A1X A1-3 A1-6 A1-5 B2 B2 B2 B2 B1 B4 B4...

Packing X-1 S-1 S-4 S-3 S-3 S-2 TAPE TAPE X-4 X-3 X-2 X-7 S-6 S-14 FRONT 3-1-3 T7300PEX

3-1-4 T5304DEX DECK EXPLODED VIEWS Deck Mechanism View 1 Some Ref. Numbers are not in sequence. Mark Description Part No. SLIDUS OIL #150 0VZZ00226 B2 B35 B553 B410 B411 B494 B567 L1053 B74 B10 L1191 B73 B9 B12 B492 B11 B571 B37 B126 L1466 B501 B8 B121 B426 B560 L1450 L1051 L1467 Floil G-374G 0VZZ00...

3-1-5 T5304DEX Deck Mechanism View 2 Some Ref. Numbers are not in sequence. Mark Description Part No. Floil G-374G 0VZZ00109 (Blue grease) Bottom Side(Grease point) Bottom Side (Grease point) View for A (Grease point) B516 B559 A B52 B507 B488 B551 B133 B568 B569 B513 B502 B570 B491 B565 B417 L1151 ...

3-1-6 T5304DEX Deck Mechanism View 3 Some Ref. Numbers are not in sequence. Mark Description Part No. Floil G-374G 0VZZ00109 (Blue grease) B359 B529 B360 B303 B514 B555 B563 B300 B562 B482 B355 B354 B483 B425 L1461 L1341 L1341 L1321 B347 L1321 Note: There are two different, but interchangeable types...

20020205 3-2-1 T7300CA MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read care-fully the product safety notice in this service manual.Don't degrade the safety of the product throughimpro...

20020205 3-2-2 T7300CA Table 1 (V501 and L551 Combination) Note 1: Purity and Convergence Adjustments must be performed following CRT replacement. Refer to Electri-cal Adjustment Instructions. Note2: Please confirm CRT Type No. on the CRT Warning Label which is located on the CRT. Then Seethe Table ...

20020205 3-3-1 T7300EL ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read care-fully the product safety notice in this service manual.Don't degrade the safety of the product throughimpro...

20020205 3-3-10 T7300EL SENSOR CBA Q501 TRANSISTOR 2SC2482 TPE6 or QQSZ02SC2482 TRANSISTOR 2SC3468(E)-AE or QQSE02SC3468 TRANSISTOR 2SC3468(D)-AE or QQSD02SC3468 TRANSISTOR KTC3207 NQSZ0KTC3207 Q502 TRANSISTOR 2SC2482 TPE6 or QQSZ02SC2482 TRANSISTOR 2SC3468(E)-AE or QQSE02SC3468 TRANSISTOR 2SC3468(D...

20020205 3-4-1 T7300DPL DECK PARTS LIST Note: There are two different, but interchangeable types of CLEANER LEVER(B359) in this model, andhave different combination with B361. Please see Table1 for details and combination. Table 1 (B359 and B361 Combination) B359 CLEANER LEVER B361 Type ID No. ID No...

- 7 - EN 9I03 OPERATING CONTROLS AND FUNCTIONS NOTE: • We do not recommend the use of universal remote controls. Not all of the functions may be controlled witha universal remote control.If you decide to use a universal remote control with this unit, please be aware that the code number givenmay not...

- 9 - EN 9I03 PREPARATION FOR USE ANTENNA/CABLE CONNECTIONS VHF/UHF COMBINED ANTENNA The VHF/UHF Rod Antenna (supplied with 13”model only) is detachable. Insert the stem of theantenna into the hole on the upper-back portion ofthe TV/VCR.Connect the VHF/UHF Rod Antenna orVHF/UHF Combination Antenna t...

- 10 - EN 9I03 INSTALLING THE BATTERIES 1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of thearrow. 2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by thepolarity (+/-) markings. 3)Replace the cover. SET UP FO...

- 11 - EN 9I03 CLOCK SET UP (AUTO / MANUAL) Make sure ... • TV/VCR power must be turned on. • Confirm that the antenna connections are correct. • The cable converter box must be turned on if yourTV/VCR is connected directly to it. (See NOTES:) • The channel is properly set in advance. NOTES: • Auto ...

- 12 - EN 9I03 DELETING (OR ADDING) CHANNEL CHANNEL SET UP AGAIN Make sure ... • Press the POWER button to turn on the TV/VCR. 1 Select “CHANNEL SET UP” Press the MENU button on theremote control.Press the PLAY/ K or STOP/ L but- ton to point to “CHANNEL SETUP”.Then, press the F.FWD/ B button. 2 Beg...

- 13 - EN 9I03 1 Select “CHANNEL SET UP” Press the MENU button on theremote control.Press the PLAY/ K or STOP/ L but- ton to point to “CHANNEL SETUP”.Then, press the F.FWD/ B button. 2 Select “ADD/DELETE CH” Press the PLAY/ K or STOP/ L but- ton to point to “ADD/DELETECH”.Press the F.FWD/ B button. ...

- 14 - EN 9I03 TV OPERATION WATCHING A TV PROGRAM 1 Turn on the TV/VCR Press the POWER button to turn on the TV/VCR. 2 Select the channel number Press the CHANNEL K or L button to select your desired channel number or press the number buttonson the remote control. Remember: If the TV/VCR is connecte...

- 15 - EN 9I03 CLOSED CAPTION SYSTEM You can view specially labeled (cc) TV programs,movies, news, pre-recorded tapes with either a dia-logue caption or text display. CAPTION mode: By choosing the caption mode, you can watch dramas, movies and news while captioningthe dialogues and the contents of n...

- 16 - EN 9I03 3 Select your desired item Press the PLAY/ K or STOP/ L button to point to your desired item.Then, press the F.FWD/ B button to select [BLOCK] or [VIEW]. • When you select the rating cate-gory and turn it [BLOCK], thehigher rating will turn [BLOCK]automatically. Also, the lower rating...

- 17 - EN 9I03 PLAYBACK This TV/VCR will operate with any cassette that has the mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes. The TV/VCR has the auto repeat function that allowsyou to repeat a tape indefinitely without touching thePLAY ...

- 18 - EN 9I03 PICTURE SEARCH This feature is very useful in finding or skipping overa particular scene on a tape. In this mode, the soundwill be muted.1)You may view a video tape at a high speed in either a forward or reverse direction by pressingthe F.FWD or REW button. (in the SP / LP / SLPmodes)...

- 19 - EN 9I03 PICTURE CONTROLS TRACKING ADJUSTMENT • Tracking adjustment will be set automatically(Digital Tracking function) when you start play-back. • However when playing pre-recorded tapes or tapesrecorded on units other than your own, noise lines(black and white streaks) may appear on the pla...

- 20 - EN 9I03 Make sure ... • TV/VCR power must be turned on. • Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape tothe point at which you want to begin recording.) NOTE: This unit will ONLY record and view the same channel. You can ONLY w...

- 21 - EN 9I03 Push(es) Display Recording length 1 push (normal recording) 2 pushes 0:30 30 minutes 3 pushes 1:00 60 minutes 17 pushes 8:00 480 minutes 3 Begin OTR Press the REC/OTR button on theTV/VCR as many times as needed.The recording length will be deter-mined by the number of times youpress t...

- 22 - EN 9I03 For every day recording : To record a TV program at the same time on the same channel every day.(Example: Monday through Sunday) Press the STOP/ L (down) button until “EVRY DAY” appears. Then, press the F.FWD/ B button. For weekly recording : To record a TV program at the same time on...

- 23 - EN 9I03 TO CANCEL AN AUTOMATIC TIMERRECORDING • After setting a program; 1)Press the POWER button.2)Repeat steps [1] ~ [2] on page 21 and select a program you want to cancel. 3)Press the T-PROG. CLEAR button.4)Press the MENU button on the remote control to return to TV mode. • While recording...

- 24 - EN 9I03 3 Set wake up time Press the PLAY/ K or STOP/ L but- ton until to point to “TIME”.Press the F.FWD/ B or REW/ s button until your desired wake uptime appears.Each additional push will increase (or decrease) thetime by 10 minutes. 4 Exit the Wake Up Timer setting Press the MENU button o...

- 25 - EN 9I03 CABINET CLEANING • Wipe the front panel and other exterior surfaces ofthe TV/VCR with a soft cloth immersed in luke-warm water and wrung dry. • Never use a solvent or alcohol. Do not spray insec-ticide liquid near the TV/VCR. Such chemicalsmay cause damage and discoloration to theexpo...

- 26 - EN 9I03 TROUBLESHOOTING GUIDE If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column toremedy the problem. PROBLEM CORRECTIVE ACTION No power. • M...

- 27 - EN 9I03 SPECIFICATIONS GENERAL SPECIFICATIONS CRT : 13 or 19 inch in-line gun, 90˚deflection tube Television system : NTSC-M Closed caption system :§15.119/FCCVideo Heads : Rotary two-head Tape width : 1/2 inch Tape speed SP : 33.40mm/sec. LP : 16.67mm/sec. SLP : 11.12mm/sec. Tuner channel TV...

- 28 - ES 0I29 1 Toma de entrada de vídeo (VIDEO)– Conéctela a la toma de salida de vídeo de su videocámara u otravideograbadora. 2 Toma de entrada de audio (AUDIO)– Conéctela a la toma de salida de audio de su equipo de audio,videocámara u otra videograbadora. 3 Botón de la alimentación (POWER)– Pú...

- 30 - ES 0I29 CONEXIONES DE ANTENA/CABLE ANT. IN OUT Antena de varilla UHF/VHF(incluído para solamente 13”) Antena combinada deVHF/UHF(no incluído) Combinador deVHF/UHF(no incluído) Antena UHF(no incluído) Antena VHF(no incluído) Desde el sistema de Cable Cable coaxilde 75 ohm (no incluído) Caja de...

- 31 - ES PREPARACIÓN DE CANALES POR PRIMERA VEZ 1) Enchufe el cable de alimentación del televisor/videograbadora en una toma de CA estándar. NOTA: Si aparezcan algunos digitos en el rincón de la pantalla, pulse el botón POWER sin desenchufar el cablede alimentación.2) Pulse el botón POWER para ence...

Printed in Malaysia 0EMN01894 T5303UD/T7303UD * * * * * LIMITED WARRANTY FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workman-ship as follows: DURATION: PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (...