Emerson CF943- Manuals

Page 2 - WARNING

DATE CODE: The date code of this fan may be found on the box, stamped in ink on a white label.You should record this data above and keep it in a safe place for future use. 2 WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’...

Page 3 - Tools Needed for Assembly; Installed Wire Length; Unpacking Instructions; blade screws

3 This Manual is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Do not install or use fan if any part isdamaged or missing. Call Toll-Free: 1-800-654-3545 ! WARNING This product is designed to use onlythose parts supplied with this product...

Page 5 - Slide the four switch levers in the wall; General; Figure 1

5 Setting Operating Frequency of Wall Control and Receiver (Figure 1) Your wall control and receiver have codeswitches which must be set in one of 16possible code combinations. The fourlevers (numbered 1, 2, 3, and 4) on theswitches are factory-set in the ON (up)position. Change the switch settings ...

Page 6 - Installation of Wall Control; Figure 3; Figure 2

Installation of Wall Control SINGLE-POLEINSTALLATION (Figure 2) 1. Disconnect power at circuit breaker or remove fuse. 2. Remove faceplate and screws from existing wall switch. Pull switch outfrom the wall box. Determine the “hot”wire and the “load” wire and disconnectthese wires from switch. Do not...

Page 7 - Figure 4; Figure 5; How to Assemble Your

4. Install a wall control in the wall box containing the “hot” wire first. Connectone black wire of the wall control to the“hot” wire. Securely connect wires withwire connectors supplied. 5. Connect the other black wire of the wall control to both remaining travelerwire(s) in the wall box and secure...

Page 8 - Figure 9; Figure 6; Position the bottom half of the; Figure 7

#10-32 x 5/16" OVAL HEAD FLANGE SCREW (2 per flange) BLADE ASSEMBLY MOTOR HOUSING ASSEMBLY FLANGE SLOT 4. Securely connect the black wire connector of the light fitter assembly tothe black motor wire connector.Securely connect the white wire of thelight fitter assembly to the white motorwire (Fi...

Page 9 - tighten the two setscrews.; Slide the coupling cover down the

7. Carefully turn the fan motor assembly upside down in preparation for hangerball/downrod installation. Place thepartially assembled fan into the top halfof the styrofoam as shown in Figure 11.Do not rest fan weight on the light fittersockets. 8. Remove the hanger ball from the downrod by loosening...

Page 10 - How to Hang; Securely attach the hanger bracket to

17. You have now completed the initial assembly of your new ceilingfan. You can now proceed withhanging and wiring your fan. 16. Reinstall the hanger ball on the downrod (Figure 16) as follows.Route the motor leads through thehanger ball and slide the hanger ballover the downrod. Install the pinthro...

Page 11 - Pull the wire leads, coming from the end; a. Connect the white fan wire and the; Position the SW105 Receiver in the; TAB; Carefully lift the fan and seat the; How to Wire

1. Pull the wire leads, coming from the end of the downrod, and the supply wiresthrough the open side of the hangerbracket. (Figure 20). a. Connect the white fan wire and the white supply wire to the whitereceiver wire (AC IN/ MOTOR N). b. Connect the black fan wire to the black receiver wire (TO MO...

Page 12 - Carefully turn the wires upward and; f. Cap the receiver yellow wire using a

WHITE SUPPLY WIRE BLACK FAN WIRE SW105 RECEIVER TO 110V SUPPLY SW113 FAN/LIGHT WALL CONTROL CAP THE YELLOW RECEIVER WIRE USING A WIRE CONNECTOR BLUE RECEIVER WIRE BLUE FAN WIRE BLACKSUPPLYWIRE WHITE RECEIVER WIREBLACK RECEIVER WIRE BLACK/WHITE RECEIVER WIRE YELLOW RECEIVER WIRE DOWNROD HI MED LOW FA...

Page 13 - How to Install

OUTLET BOX RECEIVER CEILING COVER HANGER BRACKET 1-1/4" THREADEDSTUDS (2) Figure 22 7. Slide the receiver up and over the hanger bracket. Press the receiveragainst the ceiling, then slide theceiling cover up to the threaded studsand turn until the studs protrudethrough the holes in the ceiling c...

Page 15 - INSTRUCTION TO THE USER; Reorient or relocate the receiving antenna.

15 INSTRUCTION TO THE USER (if device contains a digital device) This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residenti...

Page 16 - IMPORTANT CARE INSTRUCTIONS; Accessories

16 1. Downrod Extension Kits (see store or catalog). 2. Ceiling Fan Controls (see store or catalog). 3. Blades (see store or catalog). Do not use water when cleaning yourceiling fan. It could damage the motor orthe blades and create the possibility of anelectrical shock. ! WARNING The use of any oth...

Page 17 - Trouble Shooting; TROUBLE; Make sure; FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX

17 Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers. WARNING: Make sure main power is turned off. 2. Loose power line 2. Check line power connections connections to the fan. to...

Page 19 - Repair Parts Listing

Part Numbers Key Model No. Model No. No. Description CF943AGW00 CF943BZH00 * Hanger Pack, Consisting of: 761655-62 761655-61 1 Hanger Bracket — — 2 Hanger Ball — — 3 Downrod — — * Parts Bag, Containing: 763224 763224 4 Screw, #10-32 x 5/16” Pan Head Blade (16) — — 5 Washer, #10 flat (16) — — 6 Wire ...

Page 20 - A i r C o m f o r t P r o d u c t s; DIVISION OF EMERSON ELECTRIC CO.; LIMITED WARRANTY

Part No. F40BP73350000 Printed in China 01/07 Form No. BP7335 A i r C o m f o r t P r o d u c t s DIVISION OF EMERSON ELECTRIC CO. 8100 W. Florissant ¥ St. Louis, MO 63136 LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emers...