Page 2 - All rights reserved.; Trademarks; Limited and Restricted Rights Legend
2009 Emerson All rights reserved. Trademarks Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. © 2009 Emerson Electric Co. All other product or service names are the property of their res...
Page 3 - Contents
Contents PREFACE ................................................................................................................................................I S AFETY S UMMARY .......................................................................................................................
Page 8 - List of Figures
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide vi List of Figures Figure 1, ATCA-S201 functional block diagram .......................................................................................... 9 Figure 3 ATCA-S201 Diagram Showing Identification Label Location ...........
Page 9 - List of Tables
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide vii List of Tables Table 1 Conventions used in this manual .................................................................................................... iv Table 2 LED functional description ...................................
Page 11 - Preface; Safety Summary; War ning
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide i Preface Safety Summary The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this m...
Page 12 - ii; Flammability; EN55022 “Limits and Methods of Measurement of Radio Interference; Notice
Preface 6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide ii Flammability All Emerson PWBs (printed wiring boards) are manufactured with a flammability rating of 94V-0 by UL-recognized manufacturers. EMI Caution This equipment generates, uses, and can radiate electromagnetic ener...
Page 13 - iii
Preface 6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide iii edited, translated, or otherwise altered without the permission of Emerson Networks, Inc.
Page 14 - About This Manual; 0GbE RAID Storage-IP Carrier blade; How this manual is organized; bold
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide iv About This Manual This manual supports the following configurations and model numbers. Part Number Description ATCA-S201 10GbE RAID Storage-IP Carrier blade How this manual is organized This manual is divided into the following chapters ...
Page 15 - CTRL
6806800H62B ATCA ‐ S201 Installation and Use Guide v courier System output (for example, screen displays and reports), examples, and system prompts. ENTER The carriage return or Enter key. CTRL The Control key. Execute control characters by pressing the CTRL key and the letter si...
Page 16 - vi; Hardware Preparation and Installation; Unpacking Instructions; After removing the product from the packaging:; Antistatic Precautions
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide vi Hardware Preparation and Installation Unpacking Instructions If the shipping carton is damaged upon receipt, request that the carrier’s agent be present during the unpacking and inspection of the equipment. Unpack the equipment from the ...
Page 17 - Features of the ATCA Storage Module
ATCA-S201 Overview 6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 7 1 ATCA-S201 Overview The Emerson ATCA-S201 is an ATCA carrier blade that supplies multi-protocol IP storage services to the chassis Zone-2 backplane using Ethernet connections. The ATCA-S201 virtualizes capacity of AMC ...
Page 18 - I/O PICMG standards compliance; PICMG 3.1 Ethernet for ATCA Systems; Chassis I/O connections; ATCA; Power Module; Site B1
ATCA ‐ S201 Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 8 1.2 I/O PICMG standards compliance The ATCA-S201 10Gb RAID Storage-IP Carrier ATCA is fully compliant with the following PCI Industrial Computer Manufacturers Group (PICMG) specifications: PICMG 3.0 Advance...
Page 19 - AMC card connections
ATCA ‐ S201 Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 9 Figure 1, ATCA-S201 functional block diagram 1.3.1 AMC card connections The four AMC slots have identical features, and each accommodates a half width, mid height module. The ATCA-S201 accepts AMC cards confo...
Page 20 - 2V and 3.3V supply voltage; Ethernet Management port; RTM with an RJ-45 connector is needed to access this port.
ATCA ‐ S201 Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 10 12V and 3.3V supply voltage 1GbE management RS232 management 1.3.5.1 Ethernet Management port An Ethernet management port is routed to the Zone 3 connector. An advanced RTM with an RJ-45 connector is n...
Page 21 - LEDs; OK
ATCA ‐ S201 Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 11 1.4 LEDs Several LEDs are located on the panel of the ATCA-S201 Advanced TCA Carrier. Out of Service (OOS) OK Boot Status Hot Swap Figure 2 Front view- fully populated ATCA-S201 showing panel LEDs
Page 22 - Software driver support
ATCA ‐ S201 Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 12 Table 2 LED functional description LED Description ATCA Hot Swap LED Off: Normal, default state Blue-Blinking: Preparing for hot swap Blue-ON: ready for hot-swap removal ATCA Blade OK LED Green-ON: Blade Opt...
Page 24 - ATCA-S201 Installation; Installation and removal of the ATCA carrier blade; current requirements.; Module
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 14 2 ATCA-S201 Installation This chapter contains the procedures for installing and removing the ATCA-S201 10GbE RAID storage services blade. 2.1 Installation and removal of the ATCA carrier blade The ATCA-S201 10GbE RAID storage services b...
Page 27 - in the appropriate slot.
ATCA ‐ S201 Installation 6806800H62B ATCA ‐ S201 Installation and Use Guide 17 2. Go to the front of the system and choose an appropriate slot for the ATCA carrier blade. If also installing a companion advanced rear transition module (RTM), install it before installing the ...
Page 29 - To Verify the Hardware Installation; firmware to initialize the board.
ATCA ‐ S201 Installation 6806800H62B ATCA ‐ S201 Installation and Use Guide 19 2.10.1 To Verify the Hardware Installation 1. After power is applied to the system, wait approximately 45 seconds for firmware to initialize the board. 2. Inspect the LEDs on the front of the ATC...
Page 30 - Full configuration capabilities:; GbE
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 20 3 New System configuration 1 RS232 Con sole Setu p 2 Eth ern et Comm. Setu p 3 RAID LUN Setu p 4 Logical Volume Setu p 5 iSCSI Device Setu p 6 NFS / SMB Sh are Setu p Configuration Step: This chapter describes how to establish manageme...
Page 31 - System boot overview
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 21 3.1 RS232 Console port This port is implemented on an RJ45 connector located on the ARTM that supplies RS232 console port access. As the ATCA-S201 boots, its progress can be monitored on the console. By defa...
Page 32 - Flash boot device contents; Linux kernel code; uImage
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 22 Power-On (Sof t Reset) Jumper 1: All FW Code retrieved from “Customer” Flash Fetch “ u-boot.bin ” from flash device Jumper 1: All FW Code retrieved from “Factory” Flash -Pause- bootdelay countdown Key Presse...
Page 33 - Linux serial console shell window; default passwords listed below for security purposes.; User account; Password change procedure; xxxxxxx; Password recovery procedure
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 23 3.1.3 Linux serial console shell window If the boot is not interrupted and has completed, the RS232 port accepts administrator login for Linux shell access, and access to command line configuration tools. Af...
Page 34 - invoked, the user is prompted to set a new one at first login.; Factory reset; Login into shell window as root; fw_setenv setfactorydefaults 1; Configuring a new ATCA-S201 blade; Command line tool; Serial ports; MAC address OUI
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 24 the clear password procedure is explained in section 9.4.3 of this manual. When invoked, the user is prompted to set a new one at first login. Note: The recovery procedure affects the “root” user only; No ot...
Page 35 - Management Configuration via HTML browser; ATCA-S201 to perform and monitoring or configuration; Management configuration via secure shell (SSH); ATCA-S201 and to facilitate command line management.; Management configuration via serial console shell
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 25 Note: If no DHCP server is present, the ATCA-S201 will deactivate this port. The serial console must be then used to manually assign an IP address. This manual initialization procedure is described in sectio...
Page 36 - Command line configuration tool; labels shown in the table below; Perform manual Interactive changes; parameters in the group, along with their present values.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 26 3.5 Command line configuration tool This tool is available from either the RS232 console or a linux secure shell connection. After successful login, the user may run an executable file “atca_blade” located i...
Page 38 - Shell, configuration scripting options
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 28 At this point the user may inspect the list. If the user wishes to modify any of the listed values, enter ‘y’ at the above prompt. The configuration utility will then display each parameter, one at a time. T...
Page 39 - New system configuration, No DHCP server
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 29 responses that are applied to the tool in a macro fashion. A script allows the user to modify one or several parameters in one step. SYNOPSIS atca_blade menu_page_index <y|n|> index_skip + new_value [&...
Page 40 - Essential U-boot user commands; help; printenv; value; saveenv
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 30 3.6.1 U-boot console tool The ATCA-S201 employs a staged boot process that begins with U-boot. U-boot is an open source boot loader program that is the first code executed at system reset. As the boot execut...
Page 41 - U-boot command syntax; ping; IP address; reset; Run a sequence of commands defined in the; version; U-boot environment variables
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 31 U-boot command syntax description and lost if the system is re-booted. ping < IP address > Sends an icmp echo address to the designated IP address (entered in dotted decimal format) reset Perform soft ...
Page 42 - Manually assign management IP addresses; values are valid entries.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 32 Variable name Default value Description bootfile Uimage This is the filename name of the Linux kernel image. loadaddr 1000000 Specifies the starting memory address for storing the bootfile consoledev ttyS1 S...
Page 43 - consist of the following commands:; for administrator login and management access.; Network boot procedure; following source files located in directory named /tftpboot/:; Li nux kernel c ode; run ramboot
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 33 To manually establish IP port address, a typical new system configuration might consist of the following commands: uboot=> setenv ipaddr 192.168.1.211 uboot=> setenv gatewayip 192.168.10.1 uboot=> s...
Page 44 - Network configuration; IP host; familiar with internet protocols and TCP/IP networking.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 34 4 Network configuration 1 RS232 Con sole Setu p 2 Eth ern et Comm. Setu p 3 RAID LUN Setu p 4 Logical Volume Setu p 5 iSCSI Device Setu p 6 NFS / SMB Sh are Setu p Configuration Step: This chapter explains h...
Page 45 - Enable HTML browser access; CLI command syntax; HTML login screen
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 35 4.1 Enable HTML browser access The web browser configuration tool may be enabled or disabled for security reasons. CLI command syntax Table 10 CLI command syntax, enable/disable GUI access Convention atca_...
Page 46 - Auto logout inactivity period; Note: In absence of this file, the value is set to 600 seconds.; Forced user logout; Single session management override; following mechanisms:; Web GUI command; HTML home page
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 36 4.3.1 Auto logout inactivity period The system will automatically terminate (logout) a remote user after 10 minutes of in-activity. Optionally, the user can create this file to set an alternate inactivity th...
Page 47 - Essential System Configuration Steps; cannot occur without completing these configuration steps:
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 37 Lo g Of f Username: admin Figure 8 HTML tool, startup screen 4.5 Essential System Configuration Steps Once connected to html configuration page, it is essential that the user navigate to both the Network and...
Page 48 - System Identification and Time Zone attributes
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 38 Em erson ATCA-S201 iSCSInf ssm bSha resLVM2MD RAI DH a rdwa re RAI DPhysica l DisksMa intena nce Network Shelf I /O Sta tus CPU Sta tus ATCA Sta tus + ‐ + + + ‐ + + + StorBlade99 ATCA-S201 Netw o...
Page 49 - Hostname; The user may assign a human friendly name to the; Domain Name; Date
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 39 System Identification and TimeZone HostName DomainName Date Time TimeZone Nameservers NTP Server List Use NTP Active Settings StorBlade99 domain.com 4/6/2009 08:51:59 New_York 0.0.0.0 tick.usask.ca ...
Page 50 - Time; Time Zone; Time Zone Selections.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 40 CLI command syntax Table 14 CLI command syntax, set network property: system date Convention atca_blade set_network Y 2+ <date> + <date> Date format MM/DD/YYYY, (month,day,year) 4.6.4 Time <...
Page 51 - Name Server list; NTP Server list
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 41 Table 17 Time Zone Selections World Zone Menu item Daylight savings World Zone Menu Item Daylight savings GMT Zulu GMT London WET -Western European GMT+1 Paris CET — Central European GMT-1 GMT+2 Athens EET —...
Page 52 - S201’s clocks with a known good reference time source.; Ethernet network port identification; Table 20 Ethernet ports for chassis communications (base/fabric)
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 42 CLI command syntax Table 19 CLI command syntax, set network property: assign NTP server Convention: atca_blade set_network Y 10+ <server1> … [server5]+ <server1> … <server5> Enter one to ...
Page 53 - packets are not processed.; DHCP
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 43 CLI command syntax Table 21 CLI command syntax, set network property: Ethernet port configuration Convention: atca_blade set_network Y <portcode+> <enable> <dhcp> <ipaddr> <netma...
Page 54 - Broadcast; generally less OS and software overhead.; MAC address; memory on the blade.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 44 4.6.14 Broadcast < Read/Write > The user may manually assign the broadcast address for a port, if DHCP is NOT enabled. The broadcast address must be entered using dotted decimal notation. (e.g. 192.168...
Page 55 - VLAN Virtual Local Area Network support; add
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 45 4.7 VLAN Virtual Local Area Network support Users may configure assign any of the Ethernet ports available on the ATCA-S201 to a Virtual Local Area Networking (Virtual LAN, IEEE 802.1q). The webtool provides...
Page 56 - lines for VLAN entry; Viewing active VLAN
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 46 Convention: atca_blade set_network Y <VLANindex+> <enable> <VLANindex> Use VLANindex 52+ to modify 1 st VLAN definition Use VLANindex 60+ to modify 2 nd VLAN definition Use VLANindex 68+ to...
Page 57 - Link aggregation and bonding; Gb/s cumulative bandwidth, fault tolerance and load balancing.; Host Blade
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 47 4.8 Link aggregation and bonding The ATCA-S201 supports 802.3ad link aggregation also known as “bonding”. Bonding allows you to aggregate multiple Ethernet ports into a single group, effectively combining th...
Page 58 - Bonding, CLI command syntax; of essential elements is summarized below.; ifenslave bond0 eth0 ifenslave bond0 eth1; Preserve new; fconfig eth0 down ifconfig eth1 down; Remove bond; ifconfig eth0 down ifconfig eth1 down
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 48 4.8.1 Bonding, CLI command syntax The Linux community has created an extensive man page for ifenslave. The subset of essential elements is summarized below. Create new bond Step1: ifconfig eth0 down; ifconfi...
Page 59 - Shelf communications; Shelf Address
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 49 4.9 Shelf communications Use these menus to initialize a communication path with the chassis shelf manager, and properly monitor ATCA-S201 hardware. Em erson ATCA-S201 iSCSInf ssm bSha resLVM2MD RAI DH a rdw...
Page 60 - I/O Status attributes; Ma intena nce
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 50 Table 22 Shelf configuration menu parameters Status item Description Shelf Address Primary/Secondary Address Active Settings Current IP address of chassis shelf manager New Settings This field is used to ass...
Page 61 - Status item; Blade maintenance, miscellaneous operations
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 51 Table 23 Blade, I/O Status indication Status item Description Current I/Os / sec Bar graphs provided for each disk Read Displays the number of real-time read I/O per second (read IOPS). Write Displays the nu...
Page 62 - Rescan SAS Topology, disk refresh; This button will reset all I/O status counters.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 52 4.11.1 Rescan SAS Topology, disk refresh The physical disk assignments change as disks become utilized in a RAID definitions. Use the “Re-Draw Tree” button to rescan for physical disks, and refresh the menu ...
Page 63 - CPU Status attributes; man top
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 53 4.12 CPU Status attributes This screen displays real-time statistics for the applications running on ATCA-S201’s PowerPC processor. The data on this screen is derived from the Linux top command ( man top ), ...
Page 64 - ATCA Status attributes
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 54 4.13 ATCA Status attributes The items in this menu provide operational condition of the ATCA-S201 and the four AMC slots and RTM if installed. Ma intena nce Network Shelf I /O Sta tus CPU Sta tus A...
Page 65 - Refresh; Disable
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 55 Table 24 ATCA status indication Status item Description PCI state Collection of values pertaining to AMC modules with PCI devices Vendor 4 digit Hex value representing the PCI Vendor ID . Device 4 digit Hex ...
Page 67 - RAID Volume; Hardware RAID configuration; hardware RAID features of
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 57 5 RAID Volume Configuration 1 RS232 Con sole Setu p 2 Eth ern et Comm. Setu p 3 RAID LUN Setu p 4 Logical Volume Setu p 5 iSCSI Device Setu p 6 NFS / SMB Sh are Setu p Configuration Step: This chapter explai...
Page 68 - RAID; Disks or volumes accessed via an AMC SAS controller; JBOD mode; improved performance and redundancy.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 58 Em erson ATCA-S201 iSCSInf ssm b Sha res LVM2 LVM2 Configura tion MD RAI D Configura tion Ha rdwa re RAID Configura tion Physica l Disks /dev/sda /dev/sdb /dev/sdc /dev/sdd /dev/sde /dev/sd...
Page 69 - H a rdwa re RAI D; Parameter; Create
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 59 H a rdwa re RAI D Conf igura tion ‐ StorBlade99 ATCA-S201 Create Hardw are RAID Volume Disk Name Parent Host Bus Target Lun Vendor Product Rev Size Select 1 /dev/sda md0 0 0 0 0 HITACHI HUC101414CSS300 A...
Page 70 - Hardware RAID levels and capabilities; Important considerations and volume restrictions; How new RAID definitions alter device menu display
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 60 5.2.1 Hardware RAID levels and capabilities RAID Level RAID0 RAID1 RAID1E Description Two or more disks are grouped to provide a capacity aggregation function. The advantage is the multiplicative performance...
Page 71 - Modify existing RAID configurations; Section 1
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 61 iSCSI & NAS AMC disk modules HW RAID Physical disks sda sdb sdc Zone-2 Fabric Zone-2 Base Zone-3 RT M IP netwo rk IP host 1:1 mapping (JBOD) 1:1 mapping (JBOD) Site: B1 Site: B2 Site: B3 Site: B4 Logical...
Page 72 - Hardware RAID; Understanding the Hardware RAID status table page
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 62 Hardware RAID configuration Description Section 1 — Create RAID volumes List of remaining disks available for new RAID volume definition. Click to select disk members. Click to select RAID level Click create...
Page 73 - Software RAID configuration
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 63 5.3 Software RAID configuration Administrators may use the ‘MD RAID’ menus to configure the Software AID features of ATCA-S201 . The implementation leverages the mdadm tool available with the 2.6.23 Linux ke...
Page 74 - Submit; A maximum of 4 software-RAID volumes may be defined on each; Software RAID, CLI command syntax
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 64 m d0 ˇ Use this drop down menu to choose a volume name. Four choices: md0, md1,md2 or md3 Submit Click to commit the selections and create the new RAID device. Ignore Warnings ‘Radio button’ will ignore mino...
Page 75 - Remove volume
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 65 --remove Used to remove a disk from a volume definition. Users may later re-add the disk using the —add command. Raiddevice Device name assigned to existing volume. Example /dev/md0 <faulty-device> Des...
Page 76 - Software RAID levels and capabilities
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 66 5.3.3 Software RAID levels and capabilities RAID Level Description Data Layout Diagram RAID4 Three or more disks are grouped in fashion where all written data is available even when any single disk drive is ...
Page 77 - Prepare Logical Volumes
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 67 6 Prepare Logical Volumes for iSCSI or file sharing 1 RS232 Con sole Setu p 2 Eth ern et Comm. Setu p 3 RAID LUN Setu p 4 Logical Volume Setu p 5 iSCSI Device Setu p 6 NFS / SMB Sh are Setu p Configuration S...
Page 78 - Viewing Physical disks; Interpreting physical disk status
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 68 6.2 Viewing Physical disks Logical volumes are comprised of one or more physical disk members. Using the HTML configuration tool, the user may view the available set of physical disks. Emerson ATCA-S201 Ph...
Page 79 - Rescan SAS Topology; topology, using the button located on the Maintenance menu page.; Software Reset SAS Controller; remaining disks to the operating system.; View physical disk properties
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 69 6.2.1.1 Disk view refresh, Re-draw Tree button The physical disk assignments change as disks become utilized in a RAID definitions. Use the “Re-Draw Tree” button to rescan for physical disks, and refresh the...
Page 80 - assign them to volume groups.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 70 Table 21 HTML tool, Emerson ATCA-S201 Physical Disk (configuration screen) Parameter Description Device Name Linux SCSI device name, from ATCA-S201 management perspective Online: indicates the device is ac...
Page 81 - LVM2 Conf igura tion; Follow these instructions to create a new volume group; Click the
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 71 Em erson ATCA-S201 iSCSInf ssm bSha resLVM2 LVM2 Conf igura tion MD RAI DH a rdwa re RAI DPhysica l DisksMa intena nce + ‐ + + + ‐ + + + + StorBlade99 ATCA-S201 Available Physical Disks Disk Name Volum...
Page 83 - menu will update to show the new volume group as shown below.; Follow these instructions to create a new logical device; Enter the size of the new device in the field labeled; Follow these instructions to extend an existing volume group
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 73 6.4 Creating a Logical Device (/dev/vga/lva0) After successfully creating a volume group, the user must next create a logical device which can be assigned to iSCSI or NAS services. The LMV2 configuration men...
Page 84 - Enter the new size increase in the field labeled; Click the ‘Select’ box to choose which device will be deleted.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 74 Step 2. Enter the new size increase in the field labeled Enter size to create or extend [ ]. (It can exceed the seed value displayed in the box). Step 3. Click the ‘Extend Volume’ button 6.4.2 Delete a Logic...
Page 85 - Manage shares (prepare logical device for service); Ma na ge Sha res; Block File field; Share type; Commit a logical drive for iSCSI service
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 75 6.5 Manage shares (prepare logical device for service) By default, all logical devices are unformatted and not yet visible to either iSCSI or NAS services. The manage share menu is used to prepare a logical ...
Page 86 - Commit a logical drive for NAS service; Follow these instructions to assign NAS service
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 76 Follow these instructions to assign iSCSI service Step 1. Enter a ‘human friendly’ name for your new iSCSI share in the field labeled Share Name [ ]. Step 2. Click the ‘iSCSI box. Step 3. Click the ‘Share’...
Page 87 - applied by clicking the appropriate box and clicking ‘Update’.; Un-commit an iSCSI share; navigating to the html configuration screen:
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 77 Note: The ‘share’ in this example is not yet visible externally via IP links, and external hosts cannot yet access this resource. Administrator should proceed to chapter 8 to create NFS or SMB mount points. ...
Page 88 - Follow these instructions to un-commit a logical drive
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 78 StorBlade99 ATCA-S201 Shared Resource /dev/vga/lva0 Logical Volume Share Name Share Type Block / File Action /dev/vga/lva0 lva0 iSCSI nfs smb Block ‐ In Use ‐ Update Share Name Mount Point...
Page 89 - Un-Click the ‘nfs’ and ‘smb’ box
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 79 StorBlade99 ATCA-S201 Shared Resource /dev/vga/lva0 Logical Volume Share Name Share Type Block / File Action /dev/vga/lva0 lva0 iSCSI nfs smb Block ‐ In Use ‐ Update Share Name Mount Point...
Page 90 - iSCSI device setup tools; user must complete step 4 before this step can be accomplished.; iSCSI configuration menu; Add or create an iSCSI target
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 80 7 iSCSI device setup tools 1 RS232 Con sole Setu p 2 Eth ern et Comm . Setu p 3 RAID LUN Setu p 4 Logical Volume Setu p 5 iSCSI Device Setu p 6 NFS / SMB Sh are Setu p Configuration Step: This chapter explai...
Page 91 - Follow these instructions to create a new iSCSI target; Click the ‘add an iSCSI Target’ button.; Add or create an iSCSI LUN
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 81 Em erson ATCA-S201 iSCSI iSCSI Conf igura tion nf ssm bSha resLVM2MD RAI DH a rdwa re RAI DPhysica l DisksMa intena nce ‐ + + ‐ + + + + + + StorBlade99 AT CA-S201 iSCSI Configuration Global Settings iSNSSe...
Page 92 - LUNs Served By This Target; Fol; Use the LUN Drop down menu, to specify the LUN assignment for the
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 82 Target iqn.1995-07.com.emerson:AT C A-S2 01.Tar get 0 Alias NoAlias MaxConnections 1 InitialR2T No ImmediateData Yes MaxRecvDataSegmentLength 262144 MaxXmitDataSegmentLength 262144 MaxBurstLength 262144 Firs...
Page 93 - LUNs Served By This Target; Add a new LUN Share to This Target; blockio; Remove an individual iSCSI LUN; access is restored.; Follow these instructions to delete an iSCSI LUN; Click the ‘Remove button corresponding to the LUN you will remove.; Follow these instructions to delete an iSCSI Target; Click the ‘Submit Changes’ button at the top of the menu.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 83 1 LUNs Served By This Target LUN Path Type Remove 0 /export/iSCSI/lva0 blockio Remove Add a new LUN Share to This Target LUN Path Type Action blockio No paths available 1 ˇ ˇ Figure 27 SCSI configurati...
Page 94 - Advanced iSCSI configuration (expert mode); ‘Target Default settings’ button.; Sample ietd.conf file for iSCSI targets; Notes: Comment lines must start with a ‘#’ as first character.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 84 7.1.5 Advanced iSCSI configuration (expert mode) The iSCSI service running on the storage blade supports numerous configuration options that appear in the iSCSI section of web interface tool. Users may modif...
Page 98 - iSCSI Discovery filter configuration (expert mode)
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 88 7.1.6 iSCSI Discovery filter configuration (expert mode) The iSCSI service running on the storage blade includes the ability to limit the targets each host will see during discovery; this can often significa...
Page 99 - tools; The user must complete step 4 before this step can be accomplished.; NFS and SMB mount point configuration menus; nf s Conf igura tion
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 89 8 NFS/SMB Share setup tools 1 RS232 Con sole Setu p 2 Eth ern et Comm. Setu p 3 RAID LUN Setu p 4 Logical Volume Setu p 5 iSCSI Device Setu p 6 NFS / SMB Sh are Setu p Configuration Step: This chapter explai...
Page 100 - Export an nfs or smb share; Follow these instructions to create a new nfs File-Share Export; Click the ‘Add nfs Export’ button.; Left click the update button
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 90 These menus provides the ability to create file mount points for logical devices previously committed for file I/O share (see chapter 6 ). 8.1.1 Export an nfs or smb share These are the final steps to make a...
Page 101 - Follow these instructions to create a new smb File-Share Export; smb menu; Adjust the “Access Attributes” if desired.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 91 CLI command syntax Table 34 CLI command syntax, create nfs share Convention: atca_blade set_nfs This command invokes an interactive session to modify the nfs setting of the blade. The command will spawn a ...
Page 102 - Remove an individual file-share Export; unavailable and can be exported again at a later time.; Follow these instructions to Delete a file-share export
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 92 CLI command syntax Table 35 CLI command syntax, create smb share Convention: atca_blade set_smb This command invokes an interactive session to modify the smb setting of the blade. The command will spawn a ...
Page 103 - Advanced file share configuration (expert mode); Configuration file; Comment lines must start with a ‘#’ or “” as first character.; Sample /etc/export file for nfs file shares
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 93 8.1.3 Advanced file share configuration (expert mode) The file share services running on the storage blade supports numerous configuration features that are not part of the web interface tool, but available ...
Page 105 - Blade Maintenance and; performance of the ATCA carrier blade.; Blade Maintenance; configuration procedure.; Export System configuration file using web-GUI tool; Navigate to the Maintenance menu. Click the ‘Export’ button.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 95 9 Blade Maintenance and Firmware upgrades This chapter provides information about preserving all existing blade configuration settings and also installing and updating the firmware loaded on the ATCA-S201 st...
Page 106 - ATCA Firmware
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 96 Export system configuration file using CLI The following procedure is a detailed description of the CLI-based export system configuration procedure. Step 4. On your remote host, open a secure ftp connectio...
Page 107 - Download New Firmware package; Identifying the correct firmware image; Normal Firmware Update procedures
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 97 Each image contains a CRC signature which is validated by the system prior to loading. The normal methods for updating these code images is to establish a management connection, ( see chapter 3 ) login as ad...
Page 108 - StorBlade99 ATCA-S201 Maintenance Page; Follow these instructions to load new firmware; Click the ‘Import’ button. The import can take 1 to 5 minutes the user
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 98 Upgrade firmware procedure StorBlade99 ATCA-S201 System Maintenance Import Sof tware Update Import System Conf iguration Export System Conf iguration /backup/nvdisk.tar.gz Import Export Browse… StorBlade99...
Page 109 - DESCRIPTION
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 99 A Pop-up window notifies the user when the flash update completes. The new software becomes active at next reboot. A blade reboot button is available on the ‘ATCA Status’ menu (see StorBlade99 ATCA-S201 Blad...
Page 110 - OPTIONS; CLI flash tool, update procedure details; Upgrade firmware procedure; Establish console or ssh access to the ATCA-S201. Must be user root.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 100 OPTIONS -r : indicates the root file system should be replaced with the image on the tftp server. -k : indicates the linux kernel should be replaced with the image on the tftp server. -u : indicates the ubo...
Page 111 - Emergency firmware recovery, theory of operation
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 101 * * ************************************************* Erasing 256 Kibyte @ 31c0000 -- 99 % complete. Programming /dev/mtd2 Verifying rootfs.ext2.gz.uboot Successful update of flash /dev/mtd2 from file rootf...
Page 112 - Emergency flash recovery (factory reset); blade to fetch firmware from the read-only factory flash.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 102 AMC slo t B1 AMC slo t B2 AMC slo t B3 AMC slo t B4 DDR2 DIMM J23 J10 CPU PCIe Switch SAS 10GbE XAUI ATCA-S201 JP1 JP2 J30 J32 J33 3 2 1 3 2 1 Figure 30 ATCA-S201 Jumper locations 9.4.2 Emergency flash reco...
Page 113 - serverip; Clear root password; root password reset procedure (method 1)
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 103 4. The ATCA blade will break into the U-boot console. 5. Establish a serial connection, login into the blade as root (see section 3.2) 6. Use printenv to list the environment variables. Assign a serverip ad...
Page 114 - be asked to create one.; root password reset procedure (method 2); power cycle and some familiarity with U-boot.
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 104 8. Administrators may login as root. There is no password, and the ‘root’ user will be asked to create one. root password reset procedure (method 2) This procedure is useful when the user has access to th...
Page 115 - ATCA-S201 Mechanical; Specifications for the ATCA-S201; PICMG 2.10, Keying of ATCA Boards and Backplanes specification.; Power Requirements
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 105 10 ATCA-S201 Mechanical and Connector Information This chapter provides the specifications and connector pin outs for the ATCA-S201 module. 10.1 Specifications for the ATCA-S201 This section provides mechan...
Page 116 - ATCA-S201 Mechanical and Connector Information; NEBS Compliance
ATCA-S201 Mechanical and Connector Information 6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 106 Table 39 Environmental specifications for the ATCA-S201 SPECIFICATION VALUE Operating Temperature (airflow 5.0 CFM) 0°C ~ 55 °C Operating Temperature (airflow 2.0 CFM) 0°C ~ 23 °C Storage T...
Page 117 - Connectors and Pin assignments
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 107 Table 40 EMC Emission compliancy Description Description US: FCC 47 CFR Part 15 Class A FCC Class A emissions requirements (United States) ICES-003 2004 Class A Class A Interference-causing Equipment standa...
Page 118 - AMC Module Slots; available to provide ONE of the following configurations:
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 108 Table 41 Connector Port Identification and Location 1 AMC Slot 0 7 Zone 3, J32 RTM signal connector 2 AMC Slot 1 8 Zone 3, J33 RTM signal connector 3 AMC Slot 2 9 Zone 2, J23 Chassis connector 4 AMC Slot 3 ...
Page 119 - AMC Slot B1, Port Assignments
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 109 AMC.3 PCI Express All four slots implement a x4 PCIe connection on channels 4 to 7. All slots are directly connected to the PCI Express switch located on the ATCA carrier. 10.2.1.1 AMC Slot B1, Port Assig...
Page 120 - Port Assignments for AMC Slot B3; Zone 1 Connectors
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 110 10.2.1.3 Port Assignments for AMC Slot B3 Table 44 AMC slot 2, Port Assignments Port# Region Port Mapping Port# Region Port mapping CLK1 CLOCK -- 8 AMC-AMC -- CLK2 CLOCK -- 9 AMC-AMC -- CLK3 CLOCK PCI Expre...
Page 121 - AT; Zone 2 Connectors
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 111 AT C A PC B ATCA Receptacle view 159 13 261014 37 1115 48 1216 17 18 19 20 21 22 23 24 25 26 28 29 30 31 33 34 27 ...
Page 122 - Zone 3 Connectors
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 112 123456789 10 J23 ATCA Receptacle view Row H G F E D C B A Figure 33 Zone 2 Connector Port Pin Location Diagram Table 47 Connector J23, Zone-2 Pin Assignments Row# Interface A ...
Page 125 - Connector J30, Power Supply for RTM; The ATCA-S201 is specified to the following maximum power ratings:
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 115 Table 52 Connector J33, PCIe and Miscellaneous RTM Signal Descriptions PETx… PCI-Express transmit differential pair signals PERx… PCI-Express receive differential pair signals FCLKA Fabric clock, as defined...
Page 126 - Connector J30, RTM Power Pin Assignment
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 116 ed c ba J30- ATCA 1 2 Figure 35 ‘J30’ RTM Power Receptacle 10.2.4.4 Connector J30, RTM Power Pin Assignment The ATCA-S201 J30 connector pin assignments and descriptions appear below. Table 53 J30, RTM Power...
Page 127 - Power Supply Mezzanine Module; The ATCA-S201 incorporates a power mezzanine module from Artesyn®; SODIMM DDR Module; Note: This module is not user serviceable
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 117 10.2.5 Power Supply Mezzanine Module The ATCA-S201 incorporates a power mezzanine module from Artesyn® Technologies which performs DC-DC conversions to produce the various voltages needed by the ATCA carrie...
Page 128 - Overview; Features of the Advanced Rear Transition Module
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 118 11 RTM-ATCA-SXXX Overview The RTM-ATCA-SXXX is an Advanced Rear transition module (RTM) that features a SAS expander which provides a storage I/O path between the front ATCA board and rear I/O access panel. The front ATCA board connecti...
Page 129 - External SAS Connector; SAS Cable Length
10BRTM ‐ ATCA ‐ SXXX Overview 6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 119 Table 55 I/O Ports Available on RTM Faceplate RTM Zone-3 function RTM Faceplate RS232 Console port Port 1 —RJ45 SAS, x4 (3.0GHz) Port 2 — IB SAS connector (SFF-8470) 1Gb Ethernet Management port Port 3 - ...
Page 131 - Software Support; The information in this manual applies to the following products:; Identification Labels
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 121 Figure 38 RTM-ATCA-SXXX Front Panel LEDs 11.5 Software Support The RTM-ATCA-SXXX requires no special software to operate. As shipped from the factory, the expander is un-zoned, and configured for table rout...
Page 132 - Label
RTM-ATCA-SXXX Overview 6806800H62B ATCA ‐ S201 Installation and Use Guide 122 determine the module identity. The barcode labels provide the following information: Table 57 RTM-ATCA-SXXX Identification Labels Label Description Label 1: Final assembly P/N For Internal Use Only Label 2:...
Page 134 - Installation; Installation and Removal of the Rear Transition Module; pins to enable passing of signals via the Zone-3 connector complex.; Important Information about Your Chassis; installation of module accessories.; Observe Maximum Module Current Requirements; Module Current
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 124 12 RTM-ATCA-SXXX Installation This chapter contains the procedures for installing and removing the RTM-ATCA-SXXX. 12.1 Installation and Removal of the Rear Transition Module The RTM-ATCA-SXXX can be installed into an ATCA shelf (chassis...
Page 135 - Before You Install Or Remove The RTM; the guidelines in this section to protect your equipment.; Observe ESD Precautions; not slide the component over any surface.; Watch for Bent Pins or Other Damage
RTM-ATCA-SXXX Installation 6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 125 Module Current RTM-ATCA-SXXX (No Disk) RTM-ATCA-SXXX-2 (Two disk version) +12 V (spin up < 100 sec) 0.55 A(6.6W) 2.05 A (25 W) (staggered spin-up) +12 V normal operating 0.55 A (6.6 W) 2.05 A (24.6 W) +12...
Page 136 - for your configuration.; Installing the Advanced Rear Transition Module
RTM ‐ ATCA ‐ SXXX Installation 6806800H62B ATCA ‐ S201 Installation and Use Guide 126 12.4 Use Caution When Installing or Removing RTM When first installing boards in an empty chassis or onto a carrier card, we recommend that you start at the left of the card cage and work to the r...
Page 139 - Mechanical and Connector Information; Physical Dimensions; Environmental Specifications and Compliance
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 129 13 RTM-ATCA-SXXX Mechanical and Connector Information This chapter provides the specifications and connector pin outs for the RTM-ATCA-SXXX. 13.1 Specifications for the RTM-ATCA-SXXX This section provides mechanical, electrical, environ...
Page 140 - RTM-ATCA-SXXX Mechanical and Connector Information; Operating Shock; carries the following certifications:
RTM-ATCA-SXXX Mechanical and Connector Information 6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 130 Table 60 Environmental Specifications for the ATCA-S201 SPECIFICATION VALUE Operating Temperature (airflow 3.1 CFM) 0°C ~ 55 °C Storage Temperature -40 °C ~ 85 °C Operating Temperature ...
Page 141 - Connectors and Pin Assignments
RTM ‐ ATCA ‐ SXXX Mechanical and Connector Information 6806800H62B ATCA ‐ S201 Installation and Use Guide 131 Table 61 EMC Emission Compliancy Description Description US: FCC 47 CFR Part 15 Class A Yes, Class A emissions requirements (USA) Canada: ICES 003 Class A Yes Class A...
Page 142 - SAS Connector Port; can be ordered from Emerson.
RTM ‐ ATCA ‐ SXXX Mechanical and Connector Information 6806800H62B ATCA ‐ S201 Installation and Use Guide 132 Table 62 Connector Port Identification and Location 1 Serial console port 4 Zone 3 Connector 2 SAS Connector 5 Power connector 3 10/100/1000 Mb management port 6 RTM ...
Page 144 - Serial Console Management Port; The port is
RTM ‐ ATCA ‐ SXXX Mechanical and Connector Information 6806800H62B ATCA ‐ S201 Installation and Use Guide 134 13.2.3 Serial Console Management Port Port 4 is a low-profile RJ-45 connector jack that provides RS232 signaling. The port is wired as pass-through to the front ATCA ...
Page 147 - Connector J30, Power Supply for Advanced RTM
RTM ‐ ATCA ‐ SXXX Mechanical and Connector Information 6806800H62B ATCA ‐ S201 Installation and Use Guide 137 Table 69 Connector J33, Miscellaneous RTM Signal Descriptions PS0# Active low RTM present signal.PS0# is tied to logic GND on the ATCA blade. PS0# (Connector J33) and...
Page 149 - IPMI Functions List; Sensor data records
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 139 14 IPMI Functions List The ATCA-S201 module supports the intelligent platform management interface (IPMI) version 1.5. This system is used to collect status information from on on-board sensors as well as sensors installed on AMC or RTM...
Page 151 - RTM e-Keying Port Assignments
IPMI Functions List 6806800H62B ATCA ‐ S201 Installation and Use Guide 14 ‐ 2 Y = Calendar year of manufacturer (2008 = 8, 2010 = 0) MM = Calendar month of manufacturer (March = 03) ssss = Sequence number (reset each month) (1234) Table 75 RTM-ATCA-SXXX Example FRU Data R...
Page 152 - Supported IPMI Commands
IPMI Functions List 6806800H62B ATCA ‐ S201 Installation and Use Guide 14 ‐ 3 12 SAS_2 AMC.3 Storage signaling J32-A4, B4, C4, D4 13 SAS_3 AMC.3 Storage signaling J32-A5, B5, C5, D5 14 AMC1_EO_12 J31 C1,D1, E1, F1 15 AMC1_EO_13 J31 A1,B1, E2, F2 16 AMC1_EO_14 J31 A2,B2, C...
Page 154 - The ipmitool utility; SYNOPSIS
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 15-1 15 IPMC Firmware Upgrade Procedure This chapter provides the instruction for upgrading the IPMC (Intelligent Platform Management controller) firmware . If the ATCA-S201 requires new firmware, an upgrade can be performed remotely using ...
Page 155 - COMMAND SYNTAX EXAMPLES; The following example shows the command sequence for firmware; The following example shows the command performing firmware
IPMC Firmware Upgrade Procedure 6806800H62B ATCA ‐ S201 Installation and Use Guide 15 ‐ 2 COMMAND SYNTAX EXAMPLES E XAMPLE 1. The following example shows the command sequence for firmware upgrade of an AMC installed on a carrier: $ ipmitool -I lan -H 192.168.0.2 -T 0x82...
Page 156 - Index
6806800H62B ATCA-S201ATCA-S201 Installation and Use Guide 16-3 16 Index B Bonding ....................................................................47 C CIFs support ................................................... See SMB CLI blade status ..................................................
Emerson LD195EM8
User Manual
Emerson EWR20V4
User Manual
Emerson SLC195EM8
User Manual
Emerson CR202EM9
User Manual
Emerson HD14070
User Manual
Emerson RLC320EM9
User Manual
Emerson PD6922
User Manual
Emerson EPT427D
User Manual
Emerson 400 VMC
User Manual
Emerson CF960CK
User Manual
Emerson MICRO MOTION 2700
Installation Manual
Emerson CF787AP00
User Manual