Emerson 5100 - Manuals

1-1 Installation Connectivity Module How to Install the Connectivity Module on 7000 & 4000 Series and Series 300 ATSs The Connectivity Module (CM) mounts on a DIN rail under the ATS Controller (Group 5 & 1). A short serial cable connects the CM to the Controller. If a Power Manager (PM) or D...

Connectivity Module Installation 1-2 How to Install the Connectivity Module for a stand-alone Power Manager or Digital Power Meter The Connectivity Module (CM) mounts on a DIN rail near the Power Manager (PM) or Digital Power Meter (DPM). A long serial cable connects the Connectivity Module to the P...

1-3 Installation Connectivity Module How to View & Change Configuration Pages from a Connectivity Module To view and change configuration pages on a client computer, follow these steps: 1. Be sure that your computer is connected to the Internet. 2. Start Microsoft Internet Explorer browser on co...

Connectivity Module 7000 & 4000 Series ATSs 2-1 Device Configurator Screen for 7000 & 4000 Series ATSs The Device Configurator Screen for 7000 & 4000 Series ATSs shows the Group 5 controller configuration settings (right side) and Connectivity Module (server) configuration settings (left...

2-2 7000 & 4000 Series ATSs Connectivity Module Device Configurator Screen for 7000 & 4000 Series ATSs with a PM or DPM If a Power Manager (PM) or Digital Power Meter (DPM) is used with a 7000 & 4000 Series ATS, a button appears on the lower left corner of the Connectivity Module Device ...

Connectivity Module 7000 & 4000 Series ATSs 2-3 Configurator Screen Input and Output Names for a 7ATB with Power Manager For 7ATB only (7000 Series Automatic Transfer & Bypass-Isolation Switch), the Power Manager selection (Accessory 85 suffix letter designation) must be specified. The selec...

2-4 7000 & 4000 Series ATSs Connectivity Module Detail Screen for 7000 & 4000 Series ATSs The Detail Screen for 7000 & 4000 Series ATSs shows the switch location, ratings, timer settings, actual timer values, pickup and dropout settings, event logging, and other status indications. Detai...

3-2 Series 300 ATSs Connectity Module Device Configurator Screen for Series 300 ATSs with a PM or DPM If a Power Manager (PM) or a Digital Power Meter (DPM) is used with a Series 300 ATS, a button appears on the lower left corner of the Connectivity Module Device Configurator screen. Press the Confi...

4-2 ASCO 940/962 ATSs Connectivity Module Detail Screen for ASCO 940/962 ATSs The Detail Screen for ASCO 940/962 ATSs shows the switch location, ratings, timer settings, actual timer values, pickup and dropout settings, and other status indications. Detail Screen for ASCO 940/962 ATSs with a Power M...

Connectivity Module Stand-Alone Power Managers & Digital Power Meters 5-1 Device Configurator Screen for Power Manager or Digital Power Meter If a stand-alone Power Manager (PM) or Digital Power Meter (DPM) is used, a button appears on the lower left corner of the Connectivity Module Device Conf...

5-2 Stand-Alone Power Managers & Digital Power Meters Connectivity Module Detail Screen for Power Managers connected to a Load The Detail Screen for Power Managers shows energy levels, power measurements, settings, discrete I/O status, and other status information. Detail Screen for Digital Powe...

Connectivity Module Stand-Alone Power Managers & Digital Power Meters 5-3 Detail Screen for Power Managers connected to a Generator The Detail Screen for Power Managers shows energy levels, power measurements, settings, discrete I/O status, and other status information. Detail Screen for Digital...

5-4 Stand-Alone Power Managers & Digital Power Meters Connectivity Module Detail Screen for Power Managers connected to a Circuit Breaker The Detail Screen for Power Managers shows energy levels, power measurements, settings, discrete I/O status, and other status information. Detail Screen for D...

Connectivity Module Ethernet TCP/IP Network Connections in Windows XP & 7 A-1 How to Create an Ethernet TCP/IP Network Connection in Windows XP & 7 1. Start Windows , then click the Start button. Select Control Panel . 2. Select Network Connections ( Windows XP ) or Network and Internet and/...

Connectivity Module Troubleshooting A-3 Troubleshooting the Connectivity Module Listed below are possible problems, their causes, possible solutions Problem Cause Solution DIAG red light blinks rapidly then stays on when the CM is first powered up. Duplicate IP address. The IP address of one or more...

A-4 Create Favorites folder, 3 rd Party Modbus Configuration Connectivity Module How to create a Favorites folder for ASCO device pages and copy it to another computer To create a favorites folder and copy it to another user’s computer, the administrator should follow these steps: 1. Open the first ...

Connectivity Module SNMP Internet-standard Protocol A-5 How to set SNMP (Simple Network Management Protocol) Configuration Firmware 869764-003 and higher provides SNMP configuration. 1. On the Device Configuration screen (page 2-1 or 3-1) click the SNMP button at the bottom. 2. On the SNMP Configura...

A-6 SNMP Internet-standard Protocol Connectivity Module Recommended ASCO SNMP MIB file A file containing 934904-xxx.mib can be downloaded from the location shown below. http://www.emersonnetworkpower.com/ en-US/Products/PowerSwitchingandControls/MonitoringandControl/Pages/ ASCO5150ConnectivityModule...

Communication Address Form for Connectivity Module (CM) Row No. IP Address Subnet mask Gateway ATS Serial No. ATS Catalog No. Address set in ATS Controller* Address set in PM or DPM** Instructions: Fill in the inform ation for each Connectivity Module (CM) with an ATS, Power Manager (PM), and/ or Di...

Printed in U.S.A. © ASCO Power Technologies, L.P. 2012 All Rights Reserved. INDEX A Access, NOTICE , ii AES encryption, iii, 2-1, 3-1, 4-1 Annunciators, ATS Remote, ii ASCOSNMP.MIB, A-5 ATS information needed, ii, communication address form ATS Remote Annunciators, ii C Cable, communication, iii CH1...