Emerson 3-9000-744 - Manuals

Product Operation Personnel: • To prevent personal injury, personnel must follow all instructions of this manual prior to and during operation of the product. • Follow all warnings, cautions, and notices marked on, and supplied with, this product. • Verify that this is the correct instruction manual...

Notice THE CONTENTS OF THIS PUBLICATION ARE PRESENTED FOR INFORMATIONAL PURPOSES ONLY, AND WHILE EVERY EFFORT HAS BEEN MADE TO ENSURE THEIR ACCURACY, THEY ARE NOT TO BE CONSTRUED AS WARRANTIES OR GUARANTEES, EXPRESSED OR IMPLIED, REGARDING THE PRODUCTS OR SERVICES DESCRIBED HEREIN OR THEIR USE OR AP...

Warranty and Limitations 1. LIMITED WARRANTY: Subject to the limitations contained in Section 2 herein, Daniel Measurement & Control,Inc. (“Daniel”) warrants that the licensed firmware embodied in the Goods will execute the programminginstructions provided by Daniel, and that the Goods manufactu...

Operation Manual Table of Contents 3-9000-744 Rev F September 2013 Table of Contents i Contents Preface \ Daniel customer ser vice Signal words and symbols used in this manualImpor t ant safet y instruc tionsNoticeWarrant y and Limitations Section 1: Introduction 1.1 Over view .........................

Operation Manual List of Tables 3-9000-744 Rev F September 2013 List of Tables iii List of Tables Table 1-1 Daniel extractor tool specifications .................................................................................... 5 Table 3-1 Extractor tool list for T-slot extractable transducers ......

Operation Manual List of Figures 3-9000-744 Rev F September 2013 List of Figures v List of Figures Figure 1-1 J-mount transducer identification ................................................................................. 1 Figure 1-2 J-mount transducer identification ..............................

Operation Manual Section 1: Introduction 3-9000-744 Rev F September 2013 Overview 1 11 12 13 14 15 16 Section 1: Introduction 1.1 Overview The Daniel Ultrasonic Split Clamp Extractor Tool is designed for use on Daniel SeniorSonic TM 4 Path Gas Ultrasonic Meters only. The Daniel Ultrasonic Split Clam...

4 Extractor tool specifications Section 1: Introduction Operation Manual September 2013 3-9000-744 Rev F 1.2 Extractor tool specifications The Daniel Extractor Tool is available in two ANSI pressure ratings, 600 and 1500. The pressure rating is stamped on the Lubricator chamber assembly flange (item...

6 Extractor tool pre-use and post-use inspection Section 1: Introduction Operation Manual September 2013 3-9000-744 Rev F 1.3 Extractor tool pre-use and post-use inspection Prior to and after using the extractor tool, the following inspection procedure must be followed: Refer to drawing D-08248 Deta...

Operation Manual Section 2: Operation preparation and part replacement notes 3-9000-744 Rev F September 2013 Operation preparation 9 21 Section 2: Operation preparation and part replacement notes 2.1 Operation preparation 1. These instructions refer to details and symbols identified on Daniel Measur...

10 Operation preparation Section 2: Operation preparation and part replacement notes Operation Manual September 2013 3-9000-744 Rev F Important safety information SURFACE TEMPERATURE HAZARD Meter body and piping may be extremely hot or cold. Wear personal protective equipment when coming in contact ...

12 Part replacement notes Section 2: Operation preparation and part replacement notes Operation Manual September 2013 3-9000-744 Rev F 2.2 Part replacement notes 1. The following instructions are for removal and installation of one transducer assembly (J). Repeat the following steps for each transdu...

Operation Manual Section 3: Tool requirements 3-9000-744 Rev F September 2013 Tool list for the extractor tool with T-slot extractable transducers 13 Section 3: Tool requirements 3.1 Tool list for the extractor tool with T-slot extractable transducers 1 Molykote III is a trademark of Dow Corning Cor...

Operation Manual Section 4: Removing a transducer assembly 3-9000-744 Rev F September 2013 Steps to remove a transducer assembly from a meter while the meter is under line pressure 15 41 Section 4: Removing a transducer assembly 4.1 Steps to remove a transducer assembly from a meter while the meter ...

Operation Manual Section 5: Installing a transducer assembly 3-9000-744 Rev F September 2013 Installing a transducer assembly while the meter is under line pressure 25 51 Section 5: Installing a transducer assembly 5.1 Installing a transducer assembly while the meter is under line pressure 1. Refer ...

Operation Manual Section 6: Maintenance 3-9000-744 Rev F September 2013 Extractor tool maintenance 33 61 Section 6: Maintenance 6.1 Extractor tool maintenance The Split Clamp Extractor Tool must be returned to our factory annually or after fifty (50) transducer extractions, whichever comes first, fo...

Operation Manual Section 7: Parts list 3-9000-744 Rev F September 2013 Extractor tool parts list 35 Section 7: Parts list 7.1 Extractor tool parts list Table 7-1 Extractor tool parts list Parts list Description A Chordset assembly B Chordset socket C Chordset coupling nut D Transducer stalk assembly...

Operation Manual Appendix A: Piston and line pressure 3-9000-744 Rev F September 2013 Extractor tool piston pressure 37 A Appendix A: Piston and line pressure A.1 Extractor tool piston pressure Use Table A-1 to determine the extractor tool piston pressure needed to stabilize the extractor tool lubri...

Operation Manual Appendix B: Extractor tool pre-use and post-use inspection checklist 3-9000-744 Rev F September 2013 Inspection checklist 39 B1TOP (14) Appendix B: Extractor tool pre-use and post-use inspection checklist B.1 Inspection checklist Use the following checklist prior to and after using ...

Operation Manual Appendix C: Engineering drawings 3-9000-744 Rev F September 2013 Extractor tool drawings 41 AC1ALK TO HER.TOP (14) Appendix C: Engineering drawings C.1 Extractor tool drawings D-08248 Ultrasonic Meter Transducer Extractor Tool Operation Assembly CE-21060 Detail “A” of D-08248 CE-210...