ECHO TC-2100 - Manuals

6 PERSONAL CONDITION AND SAFETY EQUIPMENT WARNING DANGER Tiller/Cultivator users risk injury to themselves and others if the tiller/cultivator is used improperly and or safetyprecautions are not followed. Proper clothing and safety gear must be worn when operating a tiller/cultivator.Failure to do s...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 7 Vibration and Cold -- It is believed that a condition called Raynaud’s Phenomenon, whichaffects the fingers of certain individuals may be brought about byexposure to vibration and cold. Exposure to vibration and cold maycause tingling and burning sensatio...

8 D ESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictionssome assembly is required. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missingparts. Use the contents list to ...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 9 1. STOP SWITCH - "Toggle Switch" mounted on top of Throttle Trigger Housing. Move switch Forward to Run,Back to Stop. 2. THROTTLE TRIGGER - Spring loaded to return to idle when released. When accelerating, pull trigger gradually for best operating...

10 L E D O M 0 0 1 2 - C T h t g n e L ) . n i 8 4 . 4 4 ( m m 0 3 1 1 h t d i W ) . n i 6 3 . 3 1 ( m m 0 4 3 t h g i e H ) . n i 6 7 . 9 3 ( m m 0 1 0 1 s e n i T / w ) y r d ( t h g i e W ) . b l 9 1 ( g k 2 6 . 8 e p y T e n i g n E e n i g n e e n il o s a g r e d n il y c e l g n i s , e k o r...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 11 A SSEMBLY Tools Required: (2) 11mm (7/16in.) Wrenches 1. Support powerhead assembly upright on tines. Place top handleassembly to rear. 2. Loosley assemble lower handles using 6.35 x 76mm (1/4in. x 3in.)hex head shoulder bolt (A), lockwasher (B), and loc...

12 P RE -O PERATION FUEL Fuel Requirements Gasoline - Use 89 Octane [ ] gasoline or gasohol known to be goodquality. Gasohol may contain up to 10% Ethyl (grain) alcohol or 15%MTBE (methyl tertiary-butyl ether). Gasohol containing methanol(wood alcohol) is NOT approved. Two-Stroke Oil - A two-stroke ...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 13 After Refueling;- Wipe any spilled fuel from the unit.- Move at least 3 M (10 ft.) from refueling location before starting the engine. After use;- DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage ...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 15 4. START - PULL ROPE.Pull recoil starter rope until engine fires. 5. OPEN CHOKE - RUN.Move choke (B) to RUN (open) position. 6. RESTART ENGINE - PULL ROPE.Pull recoil starter rope until engine fires. WARNING DANGER When engine starts, the tines may move ...

16 M AINTENANCE Your ECHO tiller/cultivator is designed to provide many hours of trouble free service. Regular scheduled maintenance willhelp your tiller/cultivator achieve that goal. If you are unsure or are not equipped with the necessary tools, you may wantto take your unit to an ECHO Service Dea...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 17 AIR FILTER Level 1.Tools required: 25mm-50mm (1in.-2in.) medium bristle paint brush. Parts required: 90008 REPOWER TM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from enteringthe carburetor throat when the air filt...

18 SPARK PLUG Level 2.Tools Required: Spark Plug socket wrench and screw driver, Feelergauge. Preferably a wire gauge. Parts Required: Spark Plug, NGK - BPMR-7A 1. Remove spark plug and check for fouling, worn and rounded centerelectrode. 2. Clean the plug or replace with a new one. DO NOT sand blas...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 19 IMPORTANTDO NOT use a metal scraper to remove dirt from the cylinder fins. 3. Use the wooden stick or brush to remove dirt from the cylinderfins. 4. Remove grass and leaves from the grid between the recoil starterand fuel tank. 5. When installing the cov...

20 CARBURETOR ADJUSTMENT Emission Models Level 2.Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017). Parts required: None. NOTEEvery unit is run at the factory and the carburetor is set in compli-ance with EPA Phase 1 and California Emission Regulations. Inaddition, the carburetor is equ...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 21 CARBURETOR ADJUSTMENT Non-Emission Models (Without Limiter Caps) Level 2Tools Required: Screwdriver, Tachometer (ECHO P/N 90051130017). NOTEIf carburetor has limiter caps follow "Carburetor Adjustment"procedures for emission models on previous pa...

22 LUBRICATION Level 1.Tools Required: Crosshead Screw Driver Parts Required: Lithium Base Grease. Gear Housing 1. Remove tines (See Tine Removal - Installation). 2. Clean dirt from area around gear cover (A) and remove four (4)crosshead screw (B). Be careful not to tear sealing gasket (C). 3. Suppo...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 23 m e l b o r P d r a h s t r a t s - - e n i g n E t r a t s t o n s e o d - - e n i g n E e s u a C y d e m e R e n i g n E s k n a r C t a l e u F r o t e r u b r a c t a l e u f o N r o t e r u b r a c d e g g o l c r e n i a r t s l e u F d e g g o l ...

24 S TORAGE Long Term Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte-nance which includes the following: 1. Store unit in a dry, dust free place, out of the reach of children. WARNING DANGER Do not store i...

T ILLER /C ULTIVATOR O PERATOR ' S M ANUAL 25 NOTES

DEALER? Call 1-800-432-ECHO ECHO, INCORPORATED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 ECHO Incorporated 400 Oakwood Road Lake Zurich, IL 60047 Technical Publications Orders CONSUMER PRODUCT SUPPORT 1-800-673-1558 8 - 5 Mon - Fri C.S.T. S ERVICING I NFORMATION PARTS Genuine ECHO Parts and ECHO R...