ECHO SRM-261SB - Manuals - manualsarea.com

Page 3 - CAUTION; CIRCLE AND SLASH SYMBOL; DANGER

T RIMMER A TTACHMENT O PERATOR ' S M ANUAL 3 Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messagespreceded by symbols or key words. The following is an explanation of those symbols and key words and what theymean to you. S AFETY MANUAL SAFE...

Page 4 - WARNING; PERSONAL

44 Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick,• if you are taking medication,• if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection Wear eye protection that meets ANSI Z87.1 or CE requir...

Page 6 - EQUIPMENT; operation. See Assembly Section for proper adjustment.; NOTE; ALWAYS; before removing obstructions, clearing debris, or servicing unit.; DO NOT

6 EQUIPMENT WARNING Use this attachment with ECHO approved models only. Serious injury may result from the use of this attachmentcombined with a non approved ECHO product. • Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed. • Inspect shield for damage and ensure...

Page 7 - ESCRIPTION; Shaft Decal; DRIVE SHAFT ASSEMBLY -; Contains a specially designed liner and the flexible drive shaft.; NYLON CUTTING ATTACHMENT; - Shield assembly includes the Cut-Off Knife and Safety Decal. Helps

T RIMMER A TTACHMENT O PERATOR ' S M ANUAL 7 1 2 3 4 D ESCRIPTION Locate this safety decal on your unit. The complete unit illustration, found in the "DESCRIPTION" section, will help you locate it. Make sure the decal is legible and that you understand and follow the instructions on it. If t...

Page 8 - None

8 C ONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,shield installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missingpart...

Page 9 - Secure lower shaft assembly to coupler by tightening clamping; Place plastic shield on bottom of bearing housing flange.

T RIMMER A TTACHMENT O PERATOR ' S M ANUAL 9 5. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft hole. Insure locator pin is fully engaged by twisting lower driveshaft. Locator pin should snap flush in coupler. Full engagement willprevent further shaft rotation. 6. Secure lower shaft ...

Page 10 - Align locking hole in upper plate with notch in edge of gear

10 REMOVE NYLON LINE HEAD 1. Align locking hole in upper plate with notch in edge of gear housing and insert head locking tool (C). 2. Remove line head by turning it clockwise until head is completely off of shaft. 3. Remove locking tool. C WARNING The attachment will operate immediately when the en...

Page 11 - Maintenance Procedure; POWER BLENDX; Gear Housing; case to bottom of grease plug hole.; Level; = Moderate difficulty. Some specialized tools may be required.

T RIMMER A TTACHMENT O PERATOR ' S M ANUAL 11 M AINTENANCE MAINTENANCE INTERVALS Component/System Maintenance Procedure Skill Level Frequency Drive Shaft Grease 1 Every 25 hours of use Gear Housing Grease 1 Every 50 hours of use Screws/Nuts/Bolts Inspect/Tighten/Replace 1 Before each use LUBRICATION...

Page 12 - IMPORTANT; NYLON

12 B C D Drive Shaft (Lower) IMPORTANT Lower and upper drive shaft must be lubricated with high tempera-ture automotive grease every 25 hours of operation, otherwisedrive shaft assembly overheating and failure can result. 1. Loosen two (2) screws (B) and remove center locating screw (C). Pull gear b...

Page 13 - Hold the spool, opening toward you. Place index finger between

T RIMMER A TTACHMENT O PERATOR ' S M ANUAL 13 D C E C C F F B 3. Use one piece of new nylon line (C) 6 m (20 ft.) long and thread through the molded loop (D) on the spool. Pull line tight andadjust so one end is 15 cm (6 in.) longer than the other. 4. Hold the spool, opening toward you. Place index ...

Page 14 - TORAGE; Storage Hook Installation; Insert small end of hook into locating hole on attachment shaft.; PECIFICATIONS

14 MODEL ---------------------------------------------------- PAS Hi Torque Trimmer Attachment Shaft Length ------------------------------------------------ 864 mm (34.02 in.) Attachment Width ----------------------------------------- 176 mm (6.93 in.) Attachment Height -----------------------------...

Page 15 - NOTES

T RIMMER A TTACHMENT O PERATOR ' S M ANUAL 15 NOTES

Page 16 - Safety Manuals

ECHO, INCORPORATED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047-1564 WWW . ECHO - USA . COM DEALER? Call 1-800-432-ECHO o r www.echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T. ADDITIONAL OR REPLACEMENT MANUALS Safety Manuals in English/Spanish or English/French are a...