ECHO SRM-2100SB, SRM-2400SB - Manuals

6 Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers,hands, arms and shoulders may cause soreness, swelling, numbness,weakness, and extreme pain in those areas. Certain repetitive handactivities may put you at a high risk for developing a Repetitive Stres...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 7 SAFE OPERATION WARNING DANGER Do not operate this product indoors or in inadequately ventilatedareas. Engine exhaust contains poisonous emissions and can causeserious injury or death. PROVIDE ALL OPERATORS OF THIS EQUIPMENT WITH THEOPERATOR'S M...

8 √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ MODELS SRM-2400SB SRM-2100SB √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ Contents List I t e m s 1 - Power Head w/Upper Drive Shaft Assembly 1 - Lower Drive Shaft Assembly 1 - Plastic Bag (co-pack) - 1, Operator's Manual - 1, Safety Manual - 1, Warranty Registration...

10 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. GRIP - Rear (right hand) handle.3. THROTTLE TRIGGER LOCKOUT - Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. 4. STOP SWITCH - "SLIDE SWITCH" m...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 11 S PECIFICATIONS * Install and use U-Handle when operating any model with steel blade.**The RPM range shown applies for all attachments. Refer to your attachment Operator's Manual "Specifications" section for proper RPM specifications. ...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 15 P RE - O PERATION OPERATION WITH BLADES Preparing the Trimmer/Brush Cutter for Blade Use WARNING DANGER Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield and harness can resultin serious personal injury....

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 17 IMPORTANTSpilled fuel is a leading cause ofhydrocarbon emissions. Some statesmay require the use of automatic fuelshut-off containers to reduce fuelspillage. Contact your ECHO dealer forordering information. After Refueling • Wipe any spilled ...

18 O PERATION STARTING COLD ENGINE WARNING DANGER The cutting attachment should not rotate at idle. If attachmentrotates, readjust carburetor according to "Carburetor Adjustment"instructions in this manual or see your ECHO Dealer, otherwiseserious personal injury may result. NOTERefer to the...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 19 STARTING WARM ENGINE All Models The starting procedures is the same as Cold Start except DO NOT closethe choke, and do not depress throttle trigger to wide-open position. WARNING DANGER The cutting attachment should not rotate at idle. If cutt...

20 3. Recoil Starter Lay the unit on a flat clear area and pull the recoil starter handle (D)until the engine fires. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. STOPPING ENGINE 1. Throttle Release throttle, and allow engine to return to idle before shuttingengine off. 2. S...

22 AIR FILTER Level 1. Tools required: Cleaning brush, 25 - 50 mm (1 or 2 in.) medium bristlepaint brush. Parts required:SRM-2100SB 90008 REPOWER TM AIR & FUEL FILTER KIT. SRM-2400SB 90030 REPOWER TM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from enterin...

24 3. Use the wooden stick or brush to remove dirt form cylinder fins. IMPORTANTDo not use a metal scraper to remove dirt from the cylinder fins. 4. Remove grass and leaves from the grid between the recoil starter and fuel tank. 5. Assemble components in reverse order. NOTEWhen installing the engine...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 25 CARBURETOR ADJUSTMENT SRM-2100SB Emission Models Level 2.Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017)Parts required: None. NOTEEvery unit is run at the factory and the carburetor is set in compli-ance with emission regulation...

26 CARBURETOR ADJUSTMENT SRM-2400SB Emission Models Level 2.Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017).Parts required: None. NOTEEvery unit is run at the factory and the carburetor is set in compli-ance with emission regulations. This carburetor does not haveacceleration and high...

28 NYLON LINE REPLACEMENT Level 1.Tools required: Head locking tool (if head is to be removed) Parts Required: ECHO 0.095" Nylon Trimmer Line 6m (20 ft.) long. 1. Shut engine off. Lay unit on the ground with head assembly up. 2. Hold drum (A) and turn spool (B) CW (clockwise) until it stops. Pul...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 29 SHARPENING METAL BLADES Three styles of metal blades are approved for use on the ECHO BrushCutter. The 8-tooth blade can be sharpened during normal maintenance.The clearing blade and 80 tooth blade require professional service. Before sharpeni...

30 T ROUBLESHOOTING WARNING DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by groundingspark plug against cylinder, otherwise serious personal injury may result. T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 31 S TORAGE Long Term Storage (over 30 days) WARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clearof flammable debris during transportation or when storing, otherwise ser...

S ERVICING I NFORMATION PARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies foryour ECHO products are available only from an Authorized ECHODealer. When you do need to buy parts always have the ModelNumber and Serial Number of the unit with you. You can find thesenumbers on the engine ho...

SUPLEMENTO DEL MANUAL DEL OPERADOR NÚMERO DE PIEZA X7532277103 (89861056733) PARA LOS MODELO: SRM-2100SB S/N 520301 y Superior Utilice por favor este suplemento manual del operador al ensamblar y manteniendo su SRM-2100SB 1 D ESCRIPTION Page 7 EMISSION CONTROL 9992220353401/02 SUP22203534 SUPPLEMENT...