ECHO MS-41BP - Manuals - manualsarea.com

Page 2 - • Do Not exceed a tank solution temperature of 120o F/ 49o C.

WARNING WARNING: Handling the brass parts of this product will expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Wash hands after handling. CAUTION 1E WARNING: Improper use or failure to follow instructions can result in explosive fai...

Page 3 - APPLICATIONS & USE FOR YOUR SPRAYER

1. Poly Nozzle Cap 2. Retaining Nut 3. Nozzle Body 4. Nozzle Gasket 5. Elbow Figure 3 Figure 2 Figure 1 1. Brass Nozzle Cap 2. Retaining Nut 3. Nozzle Body 4. Nozzle Gasket 5. Elbow Nozzle Gasket Retaining Nut Elbow Fan Nozzle Tip 2E APPLICATIONS & USE FOR YOUR SPRAYER Avoid using a sprayer for ...

Page 4 - Threaded Bolt

INSTALLING THE PUMP HANDLEThe pump handle can be mounted on either side of the pump shaft (A). To install the pump handle place the handle (C) over the shaft (A) aligning the pump handle hole and shaft hole. Slide the bolt (B) through the aligned hole as shown in ﬁgure 1 thru 4. Tighten nut (D) to b...

Page 5 - STOWAWAY PUMP HANDLE

STOWAWAY PUMP HANDLE Pull up Rotate 180º Set into slot 4E INSTALLING THE SHOULDER STRAPThe top of the shoulder straps are attached to the tank. Attach the lower end of the straps by clipping the strap hooks to the metal frame between where the frame exits the tank and curves around. In the event tha...

Page 6 - SPRAYER COMPONENTS & USE INFORMATION, Continued; Stage 3; FILLING THE SPRAYER; Figure 1; Stage 1; STAGE FILTERING SYSTEM; Stage 2; Guide edge facing away from

5E SPRAYER COMPONENTS & USE INFORMATION, Continued Stage 3 (removable Shut-off filter) FILLING THE SPRAYER Make sure the ﬁlter basket is in place to keep debris from entering the tank. Determine the amount of mixture needed for your application. Add the proper amount of water to the tank. Add th...

Page 7 - NEUTRAL POSITION

6E SPRAYER COMPONENTS & USE INFORMATION, Continued HELPFUL SPRAYING INFORMATIONUse RAPID pump strokes to prime the pump. You will know the pressure chamber is ﬁlling with liquid when you feel ﬁrm resistance from the pump. The air in the pressure chamber is compressed from repeated strokes. By pr...

Page 10 - DISASSEMBLING AND REPAIRING THE PUMP ASSEMBLY; Clamp; Filter

7) Apply Petroleum jelly to the inside of the piston cylinder wall and on the collar, and reinstall the piston assembly into the piston cylinder. 8) Insert the piston at an angle with the leading edge of the collar placed over the slot in the piston cylinder. Bolt the piston assembly to the pump sha...

Page 11 - DISASSEMBLING AND REPAIRING THE SHUT OFF VALVE; Tank tab; Figure 4

10E 8. The pressure chamber o-ring can also be replaced. DO NOT stretch the o-ring over the bottom ﬂange. Assemble the o-ring over the top of the chamber. Apply petroleum jelly to the o-ring before reinstalling pump asembly into the tank (ﬁg. 3b).9. Reassemble backwards from step 6 thru 2, performin...

Page 12 - REPLACEMENT PARTS ORDER INFORMATION

11E REPLACEMENT PARTS ORDER INFORMATION 99944100484 Flat Fan Nozzle 99944100482 Brass Adjustable Nozzle 99944100483 Poly Adjustable Nozzle 99944100479 Hose Assembly Hose Washer Retaining Nut Hose 99944100477 Shut-off Valve Repair Kit 99944100478 Shut-off Assembly 99944100485 Nozzle Kit 99944100481 F...

Page 13 - Upper; Collar

REPLACEMENT PARTS ORDER INFORMATION 99944100474 Piston Cylinder Assembly 99944100475 Pump Piston Assembly Upper Plate Valve Upper O-ring Lower O-ring Piston Collar 99944100471 Piston Pump Repair Kit 99944100486 O-ring Kit 99944100488 Wand Clip Elbow O-ring Hose Gasket Nozzle Gasket Wand O-ring Colla...