ECHO CS-530 - Manuals

4 CS-530 TO AVOID KICKBACK 1. Hold the chain saw fir mly with both hands. 2. D o n ’ t l e t t h e n o s e o f t h e g u i d e bar contact any obstruction. 3. Tip contact may suddenly move the guide bar upward and backward,which may cause serious injury. Part Number 890191-30131 Carburetor adjustmen...

5 CS-530 PACKING LIST The ECHO product you purchased has beenfactory pre-assembled for your convenience. Due topackaging restrictions, guide bar and saw chaininstallation and other assembly may be necessary. After opening the carton, check for damage.Immediately notify your retailer or ECHO dealer o...

6 CS-530 NOMENCLATURE OF PARTS * If a decal cannot be read, a new one can be ordered from your ECHO dealer. 23 20 15 16 17 19 18 14 5 4 7 6 9 10 11 12 13 3 2 1 X524-002000 890191-30131 X503-009050 8 21 22 Part Number X503-009050 WARNING!! Read and follow all safetyprecaution in the instruction manua...

8 CS-530 VIBRATION AND COLD • It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certainindividuals, may be brought about by exposure tovibration and cold.Exposure to vibration and cold may causetingling and burning followed by loss of color andnumbness in the ...

9 CS-530 SPARK ARRESTOR MUFFLER • The spark arrestor muffler controls the exhaust noise and prevents hot, glowing par ticles ofcarbon from leaving the muffler.Make sure the spark arrestor screen is in goodrepair and properly seated in the muffler. • Certain internal combustion engines operated on fo...

10 CS-530 PREPARATION FOR USE Bolt (A) Dimple (D) Recess (E) Front hole (C) Rear hole (B) Nut (F) Guide bar Kick Guard ® Brake connector Clutch cover Brake lever(Front hand guard) Two nuts WARNING Saw chain is sharp! Always wear gloveswhen handling assembly, otherwise seriouspersonal injury may resu...

11 CS-530 5. Mount guide bar on studs and slide toward clutch to make saw chain installation easier. Installchain with cutters on top of guide bar facingforward. 6. Unlock the chain brake, and install the clutch cover over the guide bar studs. Ensure chaintension adjuster pin fits into the guide bar...

12 CS-530 FUEL AND LUBRICANT Fuel Mix Chart 50 : 1 US. METRIC Gasoline Oil Gasoline Oil Gallons US. fl. oz. L mL 1 2.6 4 80 2 5.2 8 160 5 12.8 20 400 FUEL STATEMENT GASOLINE - Use 89 Octane [(R+M)/2] (mid grade or higher) gasoline or gasohol known to be goodquality.Gasohol may contain up to 10 % Eth...

13 CS-530 HANDLING FUEL MIXING INSTRUCTIONS - 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. IM...

14 CS-530 Oil tank cap Fuel tank cap Cap indication Fuel/oil tanks are indicated by the followingillustrations. CHAIN LUBRICANT Proper lubrication of the chain while in operationreduces friction between the chain and the guidebar to a minimum and assures a longer service life. • Use bar and chain oi...

15 CS-530 WHEN THE ENGINE IS COLD CAUTION Make sure the bar and chain are free fromany obstruction when starting the chain saw. • Move chain brake lever fully forward to lock chain brake before starting. • Fill the fuel tank with fuel mixture. It is not permitted to fill fuel above the shoulderlevel...

16 CS-530 STOP Ignition switch Throttle trigger RUNNING • When engine star ts, keep idling for a few minutes. • Set the brake lever in the unlocked position before starting to cut. • Pull throttle trigger gradually and increase revolution of the engine. • The chain starts running when the engine rea...

17 CS-530 CUTTING INSTRUCTION Kickback GENERAL CAUTION • Read the ECHO “CHAIN SAW SAFETY MANUAL” included with your chain saw foradditional cutting and safety instructions. • Wear suitable hearing protection such as earmuffs or earplugs to protect againstobjectionable or uncomfortable loud noises. •...

18 CS-530 FELLING THE TREE A falling tree can seriously damage anything it mayhit - a car, a house, a fence, a power-line, oranother tree.There are ways to make a tree fall where you wantit, so first decide where that is!Before cutting, clear the area around the tree.You will need good footing while...

20 CS-530 Chain brake function When the lever is pushed forward, chain brakeinstantly stops the chain. Chain brake unlock When the lever is fully pulled, toward theoperator, brake is unlocked. Kickback Kickback motion CHAIN BRAKE OPERATION • Set the lever in the unlocked position before starting to ...

21 CS-530 End of the guide bar may be placed at the height of about 50 cm (20 in.). 50 cm(20 in.) AUTOMATIC CHAIN BRAKE Kickback produced from the tip of the guide bar willtrip the automatic chain brake. To make sure thatthe automatic chain brake operates properly, followthese steps: 1. Stop the eng...

22 CS-530 CHAIN AND GUIDE BAR COMBINATION The following combinations are recommended for model CS-530 . @ Standard configuration GUIDE BAR (Low-kickback) Replacement guide bars.The following guide bars may be considered tohave equivalent kickback energy.• Sprocket nose guide bars of the same length ...

23 CS-530 MAINTENANCE AND CARE IMPORTANT Time intervals shown are maximum.Actual use and your experience will determinethe frequency of required maintenance. Your ECHO chain saw is designed to provide manyhours of trouble free service. Regular scheduledmaintenance will help your chain saw achieve th...

24 CS-530 CARBURETOR ADJUSTMENT Every unit is run at the factory and the carburetor isset in compliance with Emission Regulations. Inaddition, the carburetor is equipped with “H” (HighSpeed) and “L” (Low Speed) needle adjustmentlimiters that prevent settings outside acceptablelimits. 1. Before adjus...

26 CS-530 GUIDE BAR • Clean before using. - Clean the groove of the guide bar with a small screwdriver. - Clean oil holes with a wire. • Reverse guide bar periodically.• Check sprocket and the clutch and clean the bar mount area before installation of the bar.Replace either or both if worn. SPROCKET...

27 CS-530 SETTING THE SAW CHAIN Sharpen lower edge Drive link Tie strap Right hand cutter Preset tie strap Left hand cutter Guard link Top plate Side plate Depth guage Impor tant points for proper maintenance of sawchain:• Keep the cutters sharp at all times.• Keep the left and the right cutters pro...

29 CS-530 TROUBLESHOOTING Problem Engine — hard to start Cause Remedy — does not start Engine Fuel at No fuel • Fuel filter clogged • Clean or replace cranks carburetor at carburetor • Fuel line clogged • Clean • Carburetor • Ask your ECHO dealer Fuel at No fuel at • Carburetor • Ask your ECHO deale...