ECHO 99944200470 - Manuals - manualsarea.com

Page 3 - IMPORTANT; WARNING DANGER; Shaft Decal

P OWER E DGER A TTACHMENT O PERATOR ' S M ANUAL 3 S AFETY DECALS Locate these safety decals on your unit. The complete unit illustrationfound in the "DESCRIPTION" section, will help you locate them. Makesure the decals are legible and that you understand and follow theinstructions on them. I...

Page 4 - Physical Condition; Your judgment and physical dexterity may not be good:; Eye Protection; ECHO recommends wearing hearing protection whenever; Proper Clothing; • Pants should have long legs, shirts with long

4 Symbol description/application Symbol form/shape Symbol description/ application Symbol form/shape Hot Surface Carburetor adjustment - Idle speed Carburetor adjustment - High speed mixture Symbol description/application Symbol form/shape Symbol description/ application Symbol form/shape Read and u...

Page 5 - EXTENDED

P OWER E DGER A TTACHMENT O PERATOR ' S M ANUAL 5 EXTENDED OPERATION / EXTREME CONDITIONS Vibration and Cold -- It is believed that a condition called Raynaud’s Phenomenon, whichaffects the fingers of certain individuals may be brought about byexposure to vibration and cold. Exposure to vibration an...

Page 6 - ESCRIPTION; produced during the edging operation.; CONTENTS; - Power Edger Attachment; SAFE; Safety Manual for instructions on Safe Operation.

6 D ESCRIPTION After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.Use the contents list to check for missing parts. 1 5 6 4 3 2 1. DEBRIS SHIELD/FLAP - Mounted over the cutting attachment. Helps protect operator by deflecting debri...

Page 7 - Carefully fit attachment drive shaft assembly into coupler (B) to

P OWER E DGER A TTACHMENT O PERATOR ' S M ANUAL 7 S PECIFICATIONS MODEL ----------------------------------------------------- POWER EDGER ATTACHMENT Shaft Length ------------------------------------------------ 845 mm (33.25in.) Attachment Width ----------------------------------------- 165.1 mm (6....

Page 8 - Secure lower shaft assembly to coupler by tightening clamping; PERATION; Operating Techniques; WARNING

8 4. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft hole. Insure locator pin is fully engaged by twisting lower driveshaft. Locator pin should snap flush in coupler. Full engagement willprevent further shaft rotation. 5. Secure lower shaft assembly to coupler by tightening clamping ...

Page 9 - Before edging, plan your direction of travel so that the unit will; AINTENANCE; the unit be returned to your ECHO dealer for servicing.; MAINTENANCE

P OWER E DGER A TTACHMENT O PERATOR ' S M ANUAL 9 INCREASE DEPTH WHEEL ADJUSTMENT KNOB DECREASE DEPTH 1/2 in. 4. Adjust the blade's depth of cut to produce a fine cut betweensidewalk and grass using a minimum blade depth, usually withabout 13 mm (1/2 in.) of the blade into the ground. 5. Before edgi...

Page 10 - Open End Wrench, Grease Gun; LUBE; Gear Case

10 BLADE REPLACEMENT / LUBRICATION Level 1. Tools Required: Scrench, Locking Tool, Needle Nose Pliers, 8 mm Open End Wrench, Grease Gun Parts Required: ECHO ® LUBE TM 8 oz. (P/N 91014) or Lithium Base Grease, Blade P/N 69601552632 Gear Case NOTEGrease gear case every 50 hours of use. Replace blade w...

Page 11 - Pull gear box and shield from drive shaft housing.; dirt on the flex cable.

P OWER E DGER A TTACHMENT O PERATOR ' S M ANUAL 11 Drive Shaft (Lower) IMPORTANTLower and upper drive shaft must be lubricated with hightemperature automotive grease every 25 hours of operation,otherwise drive shaft assembly overheating and failure can result. 1. Loosen two (2) screws (A) and remove...

Page 12 - Call; Purchasing from your Echo Dealer.

ECHO, INCORPORATED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 www.echo-usa.com DEALER? Call 1-800-432-ECHO www.echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T. S ERVICING I NFORMATION PARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies foryour ECHO produ...

Page 13 - Tools Required: 13 mm; Herramientas requeridas:; Caja de engranajes; NOTA; Eje de Manejo; IMPORTANTE; Carter d’engrenages; REMARQUE; Arbre moteur

Specification (Pg. 7) Gear Ratio ----------------------------- 2.07:1 Weight w/Blade ---------------------- 2.54 kg (5.6 lbs.) Maintenance (Pg. 9)Maintenance Intervals Drive Shaft Every 50 hours of use Gear Housing Every 15-25 hours of use Blade Replacement/Lubrication (Pg. 10) Tools Required: 13 mm...