Eagle 480 - Manuals

iii Configure NMEA ........................................................................ 69Coordinate System Selection...................................................... 69 Setup Loran TD:...................................................................... 70 Map Fix ...........................

iv Trail Update Rate (Time, Distance) ................................... 92 Delete Trail ............................................................................. 93New Trail................................................................................. 93Trail Visible/Invisible and Other Tra...

1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of digital GPS! We know you're anxiousto begin navigating, but we have a favor to ask. Before you grab theIntelliMap  480 and begin installing it, please give us a moment or two to explain h...

2 Section 3 contains short, easy-to-scan GPS lessons that follow one an-other in chronological order. They're all you'll need to know to find yourway on the water or in the wilderness quickly. After you've learned the basics (or if you already have some GPS expe-rience), you may want to try out some...

3 Input power: ................... 10 to 15 volts DC. Case size: ......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6 cm); sealed and waterproof; suitable forsaltwater use. MMC slots: ...................... One with waterproof door (SD card compati- ble). Recording: .......

4 NOTE: The above memory capacities refer only to the IntelliMap 480's on-board memory. The amount of GPS data you can record and save forrecall later is only limited by the number of MMC cards you have. NOTICE! The storage temperature range for your IntelliMap 480 is from -4 de-grees to +167 degree...

6 Introduction to GPS and WAAS Well, now you know the basics of how the unit does its work. You mightbe ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your IntelliMap 480 and plug in the power. Oryou might want to see how our text formatting makes the ...

8 You'll find that using your GPS receiver is both easy and amazinglyaccurate. It’s easily the most accurate method of electronic navigationavailable to the general public today. Remember, however, that thisreceiver is only a tool. Always have another method of navigation avail-able, such as a map o...

9 For example, instructions for navigating a trail would look like this: 1. From the Map Page, press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ to Trail 1 | ENT | → | ↓ to N AVIGATE | ENT . 3. You are asked to wait while it converts the trail into a route. 4. The wait message disappears and t...

11 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, butwe recommend this installation sequence: Caution: You should read over this entire installation section before drill-ing any holes in your vehicle or vessel! 1. Determine th...

12 You need to select an antenna installation location that has a clear, un-obstructed view of the sky. After the module is installed, route the cableto the unit, plug it in the center socket on the back and your system isready to use. See the module's instruction sheet, publication part num-ber 988...

13 For example, if you have to extend the power cable to the battery orpower buss, attach one end of the fuse holder directly to the battery orpower buss. This will protect both the unit and the power cable in theevent of a short. It uses a 3-amp fuse. Power connections for the IntelliMap 480 GPS un...

15 Optional R-a-M mounting system. Bracket Installation Mount the IntelliMap 480 in any convenient location, provided there isclearance behind the unit when it's tilted for the best viewing angle. Youshould also make sure there is enough room behind the IntelliMap 480 toattach the power and GPS ante...

16 Front view (left) and side view (right) showing dimensions of the IntelliMap 480 when mounted on gimbal bracket. After drilling the hole, pass the antenna connector up through the hole from under the dash. Pass the power cable's bare-wire end down though the hole from the top. If you wish, you ca...

17 In-dash mounting template for the IntelliMap 480, showing dimensions. NOTE: The figure above is not printed to scale. a scaled template (FM-5 In-Dash Adapter Kit instructions) is available for free download from our web site, www.eaglegps.com. Portable Installation Like many Eagle products, the I...

18 Install batteries in power pack battery adapter. MMC or SD Card Memory Card Installation Your IntelliMap 480 uses a MultiMedia Card to store information, suchas custom maps, waypoints, trails and other GPS data. The unit canalso use Secure Digital Cards (SD card or SDC) to store data. NOTE: Throu...

19 Memory card compartment with a 16 MB MMC card installed. To remove an MMC 1. Open the card compartment door by unscrewing the thumb screw.The screw should only be finger tight. If it was over-tightened, use athumbnail, a coin or a screwdriver to open the door. 2. Just press a finger against the l...

21 Section 3: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 4 is arranged in alphabetic...

22 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or adjust a feature. This also accessessearch functions for streets, intersections, addresses and highway exits. 4. ARROW KEYS – These keys are used to navigate through the menus, make menu selections, mo...

24 Pages The unit has three Pages that represent the three major operating modes.They are the Satellite Status Page, the Navigation Page and the MapPage. They are accessed by pressing the PAGES key, then using → or ← to select a Page. (Clear the Pages Menu by pressing EXIT .) Pages Menu, showing som...

26 The Satellite Status Page has its own menu, which is used for settingvarious options. (Options and setup are discussed in Sec. 5). To accessthe Satellite Status Page Menu, from the Status Page, press MENU . Navigation Page This screen has a compass rose that not only shows your direction oftravel...

27 Speed (ground speed) is the velocity you are making over the ground. (Ifyou wish, you can customize the Speed data box to display ClosingSpeed instead. Closing Speed is also known as velocity made good. It'sthe speed that you're making toward the waypoint. For instructions,see the Customize Page ...

30 national forests and parks); some major city streets; Interstate, U.S.and state highways; Interstate highway exits and exit services informa-tion; large- and medium-sized lakes and streams; and more than 60,000navigation aids and 10,000 wrecks and obstructions in U.S. coastal andGreat Lakes water...

31 Tip: In some urban areas, businesses are so close to one another thattheir POI icons crowd each other on the screen. You can reducescreen clutter and make streets and other map features easier tosee by simply turning off the display of POIs you're not watching for. (To see how, check the text on ...

32 Pages Menu with Two Map option selected, left. Map Page with two map windows, at right. The left map is active. Resize Window is another extremely handy feature for pages that havetwo major windows. You can change the horizontal size of the windowsto suit your viewing preference. Here's how: 1. F...

33 Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, trynavigating to a location at least a few blocks away. While you're learning,navigation in too small an area will constantly trigger arrival alarms. 1. Connect the unit to electric power and the antenna...

34 Find Your Current Position Finding your current position is as simple as turning the unit on. Un-der clear sky conditions, the unit automatically searches for satellitesand calculates its position in approximately one minute or less. NOTE: "Clear sky" means open sky, unobstructed by terra...

35 The selected airport to the northwest is 4.2 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map andfind the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob-ject. On most items, a pop-u...

36 2. You could search the entire restaurant category, but in this examplewe will narrow our search. Press → to S UBCATEGORY column| ↓ to F AST F OOD C HAINS | ENT | ↓ to N EAREST | ENT . 3. The unit says it is calculating, then a list of restaurants appears,with the closest at the top of the list, ...

37 6. The unit's map appears, with the cross-hair cursor highlighting therestaurant' s POI symbol. a pop-up data box shows the POI's name, dis-tance and bearing. a data box at the bottom of the screen continues todisplay the location's latitude and longitude. Map screen showing Finding Waypoint, the...

38 Create Waypoint at Current Position While you are traveling, press WPT | WPT . The waypoint is saved and automatically given a name with a sequential number, such as "way-point 003." The waypoint symbol and number appear on the map. Sequence for setting a waypoint. Step 1: while traveling...

39 Create Waypoint on Map 1. Use the arrow keys to move the cursor to the place where you wantto make a waypoint. 2. Press WPT | WPT . The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 001." The waypointsymbol and number appear on the map. Creat...

40 Navigation Page, navigating toward waypoint 004 and leaving a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or familymember fall overboard. This situation can be deadly on any body of wa-ter — fresh or salt. It's particularly dangerous at night...

41 Navigating to Man Overboard: Man Overboard Activated message, left, Navigation Page, center, Map Page, right. The victim is to the starboard of the vessel; the GPS shows which direction to steer to for the rescue. The man overboard position is also stored in the waypoint list for futurereference....

42 3. Press MENU | ENT and the unit will begin navigating to the cursor lo- cation. The Map Page will display a dotted line from your current position to thecursor position. The Navigation Page displays a compass rose showingnavigation information to your destination. See the following examples. The...

43 particularly handy when you are trying to retrace your trip and go backthe way you came. On the screen, trails are represented by a solid lineextending from the back of the current position arrow. The unit is set at the factory to automatically create and record a trailwhile the unit is turned on...

44 New trail, named "Trail 15," is created when Trail 14 is made inactive. Any new travel will be recorded in this trail, which is active and visi- ble. Trails do not need to be visible in order to be active. You can save and recall up to 10 different plot trails, which can also becopied to ...

45 To turn on trail display: 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ | ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the desired Trail Name | ENT . 3. Press ↓ to A CTIVE | → to V ISIBLE | ENT . To return to the previous page, press EXIT | EXIT | EXIT | EXIT . Navigati...

48 NOTE: If you are already located at or near the end of your trail, the arri-val alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and follow your unit. 6. When you reach your destination, be sure to cancel your navigation:press MENU |...

49 The Transfer My Data submenu asks if you want to save data to the MMC or load data from the MMC into the unit's memory. 2. The Transfer My Data menu includes a message which tells you if anMMC is present or not. If no MMC is present, you must first insert acard into the unit in order to activate ...

50 4. Loading to unit memory : There may be more than one GPS Data File (*.USR) on the card. To select a file, press ENT to activate the selec- tion box, use ↓ or ↑ to highlight the file, then press ENT to accept the selection. Next, press ↓ to L OAD D ATA | ENT . The unit will display a com- pletio...

51 Section 4: Advanced GPS Operations Find Distance From CurrentPosition To Another Location 1. While on the Map Page press: MENU | ↓ to F IND D ISTANCE | ENT . 2. Center your cursor over the position you want to find the distance to.a rubber band line appears, connecting your current position to th...

52 Icons Icons are graphic symbols used to mark some location, personal point ofinterest or event. They can be placed on the map screen, saved and re-called later for navigation purposes. These are sometimes referred to asevent marker icons. This unit has 42 different symbols you can pickfrom when c...

53 1. Press MENU | ↓ to D ELETE M Y I CONS | ENT . 2. Press ↓ to D ELETE A LL I CONS , D ELETE B Y S YMBOL , or D ELETE F ROM M AP and press ENT . Delete icons menu. The Delete All Icons command will ask if you are sure. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by S...

54 a route provides the automatic capability to navigate through severalwaypoints without having to reprogram the unit after arriving at eachwaypoint. Once programmed into the GPS unit, a route provides theoption of navigating forward through the route waypoints or in reverseorder (you can even begi...

55 2. Press ↓ to (E ND OF R OUTE ) | ENT | ↓ to A DD F ROM M AP | ENT . The Map Page appears with the cursor showing. Edit Route menu, left. Edit Route Waypoints menu, right, with Add From Map command selected. 3. Use the Zoom keys and arrow keys to move the map and cursor untilthe cursor is centere...

56 Route creation sequence, continued: Fig. 4. Point (3) set at on-ramp turn. Fig. 5. Waypoint (4) set at highway exit to frontage road leading to river. Waypoint (5) ends the route at a tree stand in the hunting area. Fig. 6. Press EXIT to save the route and you return to this screen. 5. Move the c...

57 Edit a Route Name You can edit the route name if you wish. 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Press ↓ to route name | ENT | ENT . 3. Press ↑ or ↓ to change the first character, then press → to move the curso...

58 NOTE: When adding waypoints to a route, the inserted waypoints will ap-pear in the route in front of the waypoint you have selected. To in-sert waypoints at the end of the route, make sure to select "(End ofroute)" before adding them. Navigate a Route 1. From the N AVIGATION P AGE , press...

59 Navigating along a route: Fig. 1 shows the Navigation Page at the startof a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, thetraveler has arrived at Wpt 1; the arrival alarm has been triggered and the bearing arrow on the compass rose has turned to point toward Wpt 2, off to ...

60 Tip: You can quickly call up the Edit Trail menu by selecting a trail onthe map with the cursor. Simply move the cursor over a trail and apop-up box appears. Press WPT and the Edit Trail menu opens. At left, trail selected with map cursor. The pop-up box shows distance and bearing from current po...

61 Utilities Utilities are useful tools for traveling or for outdoor activities. Alarm Clock To get to the alarm clock menu: press MENU | MENU | ↓ to T IMERS | ENT | ↓ to A LARM C LOCK | ENT . Sun/Moon Rise & Set Calculator To get to the Sun/Moon menu: press MENU | MENU | ↓ to S UN /M OON C ALCU...

63 4. The Edit Waypoint menu appears. You can simply save the waypointby pressing EXIT | EXIT or you can edit the waypoint. Set a Waypoint by Projecting a Position This feature sets a waypoint at a point located a specific distance andbearing from a reference position. The reference position can be ...

65 Section 5: System & GPS Setup Options Alarms This unit has several GPS alarms. The factory default setting has all ofthese but the anchor alarm turned on. You can turn the alarms off andon and change their distance settings. You can set an arrival alarm to flash a warning message and sound at...

66 3. To change distance settings, scroll ↓ or ↑ to select the desired cate- gory, then press → | ENT to activate the distance dialog box. Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct. 4. When your adjustments are finished, retur...

67 GPS Auto Search on the Satellite Status Menu. You can force the unit to immediately kick into auto search mode.Here's how: From the Satellite Status page, MENU | ↓ to GPS A UTO S EARCH | ENT | ← to Y ES | ENT . Check MMC Files and Storage Space To check MMC Files:Press MENU | MENU | ↓ to B ROWSE ...

68 Menus for changing Com Port settings. For connectors and wiring information for another device, see page 14.For assistance in configuring the unit to communicate with anotherdevice, consult the factory; customer service phone numbers are in theback of this manual. Also see the entries below for C...

69 4. Press ENT , then use ↑ ↓ → ← to enter the station frequency, then press ENT . 5. Press → to B IT R ATE | ENT then use ↑ ↓ to select the station bit rate, then press ENT . 6. a. If you are not using a Starlink DGPS receiver, press EXIT | EXIT | EXIT | EXIT to return to the previous page. B. If ...

71 Configure Loran TD menu. Map Fix Map Fix is used with charts or maps. This system asks for a referenceposition in latitude/longitude, which you take from a marked locationon the map. It then shows the present position as distance on the mapfrom that reference point. For example, if it shows a dis...

72 It's shown as a ratio, for example 1:24000. Press EXIT and the unit re- turns to the Configure Map Fix screen. Configure a map fix so the unit can find your position on a printed chart or topographical map. Press → to S ELECT O RIGIN | ENT | ENT | ENT to bring up the waypoint list. Select the way...

73 Customize Map Page While on the Map Page, press PAGES | ↓ or ↑ to select Option Name | ENT . DGPS Status The DGPS Status screen shows whether DGPS is off or on, and it de-scribes the quality of the DGPS signal. This screen is useful if you haveto diagnose a DGPS problem. 1. Press MENU | MENU | ↓ ...

74 to erase this menu. a message and tone appear periodically, warningyou that the simulator is on. To turn the simulator off, repeat the abovesteps or turn the unit off. While in simulator mode, you can press EXIT to clear the steering and speed boxes from the screen while continuing the simulation...

77 in the center. The large ring touching the left and right sides of thescreen is 100 miles in diameter (same as the zoom range). The secondsmaller ring is 50 miles in diameter (always 1/2 the zoom range). The distance from your current position to the smaller ring (the ring'sradius) is 25 miles (a...

78 GPS Setup Menu, left, Map Datum Menu, right. Map Detail Category Selection This menu determines which of the mapping features are shown on thescreen. This includes, waypoints, trails, icons, cities, highways, etc. Youcan selectively turn on or off any of these items, customizing the map toyour ne...

79 Map orientation at left is shown in north up and at right, track up. This is fine if you're always traveling due north. What you see to yourleft corresponds to the left side of the map, to your right is shown onthe right side of the map, and so on. However, if you travel any otherdirection, the m...

80 NOTE: In North Up and Course Up, the present position arrow appears inthe center of the map page. In Track Up, the position arrow appearscentered in the lower third of the page. Navionics  Charts Your unit can display Navionics  electronic charts on MMCs. They work just like a MapCreate custom ...

81 3. To turn off a Navionics chart, From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to N AVIONICS M AP C HOICE | ENT . Use ↑ or ↓ to select E AGLE , then press ENT | EXIT | EXIT . Port Information Navionics charts contain Port Services information, represented by an-chor icons on the map ...

82 Port Services information screens. Tidal Current Information Navionics charts contain Tidal Current information,represented at large zoom ranges by a box icon withthe letter " C ." The icon stands for a Tidal Current Station location. An example is displayed at right. When you zoom in to ...

83 Current Information screen. The Tidal Current Information screen displays daily tidal current datafor this station on this date at the present time. The graph at the top ofthe screen is an approximate view of the flood and ebb pattern for theday, from midnight (MN), to noon (NN) to midnight (MN)....

84 To view tide information: 1. Select a Tide Station icon: use the arrow keys to move the cursor overan icon. When it is selected, a pop-up name box appears. 2. After selecting the Tide Station icon, press WPT to display the Tide Information screen. Navionics chart showing Tide Station icon selecte...

85 The height scale on the top right side of the graph changes, based uponthe maximum range of the tide for that day. The MLLW line also ad- justs its position as the height scale changes. You can look up tidal data for other dates by changing the month, dayand year selection boxes. To select anothe...

86 The Position Pinning feature was developed so that when you stopped,the unit locked the present position on the GPS plotter until you moveda short distance or exceeded a very slow speed. The command remains available in the unit's software, but we recom-mend that you leave it in the default off (...

87 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to R EQUIRE DGPS | ENT . 2. To return to the last page displayed, press EXIT | EXIT . 3. You can return to this command and press ENT again to turn the fea- ture off. GPS Setup command, left; Require DGPS command on the GPS Setup Menu, right. Scree...

88 To adjust the display's brightness:Press ↓ to B RIGHTNESS . Press → or ← to move the bar. The left end of the scale is minimum contrast; the right end is maximum contrast. To adjust the screen's display mode: Press ↓ to D ISPLAY M ODE | ENT |press ↑ or ↓ to select mode | EXIT . Display Mode menu....

90 System Setup command left; Software Information command, center. At right, the Software Information screen. 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to S OFTWARE I NFO | ENT . 2. Read the information displayed on the screen.3. To return to the last page displayed, press EXIT | EXIT | ...

91 To set Alarm Style: Press ↓ to A LARM S TYLE | ENT . Press ↑ or ↓ to change the style, then press ENT . After the option is set, press EXIT | EXIT to return to the page display. Track Smoothing This is a factory setting on the GPS Setup menu that should always be left on . When stopped or traveli...

94 On the Edit Trail menu, press ↓ or ↑ to highlight the section you wish to change, then press ENT . Make your changes, then press EXIT to erase this menu. Related trail functions are discussed in further detail underthe Trails topic in Sec. 4, Advanced GPS Operations . Units of Measure This menu s...

95 Section 6: Searching NOTE: The background map loaded in your unit lets you to search for U.S.Interstate Highway exits and exit services, as well as some landfeatures, including cities and lakes. For a full set of searchable landfeatures, including landmarks, streets, addresses and Points of In-te...

96 Find Address Menu. 4. To enter a street name , press ↓ to S TREET | ENT . There are two op- tions: a. You can spell out the name in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then press E...

97 NOTE: We recommend that you do not enter a city name unless the list you are given is too large when searching without it. This unit can ac-tually search quicker without a city and you save time by not en-tering a city name. Find City field, left, Search in particular city only option, center; Fi...

98 Tip: If the address also happens to be an item in the Point of Interestdatabase, you can look up the item's phone number in the WaypointInformation list. With the address location selected by the cursor onthe map, press WPT . The POI's Waypoint Information window ap- pears, with the Go To Waypoin...

99 Find Interstate Highway Exits 1. From the Map Page, press MENU | ↓ to H IGHWAY E XITS | ENT , which calls up the Find Exit menu. Find Highway Exits command, left, and Find Exit menu, right. 2. First, select a highway name by pressing ENT , which calls up the Find By Name menu. There are two highw...

100 Find Exit menu, with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. a. Press ENT to navigate or "go to" the exit. B. Press → | ENT to find the exit on the map. "Go To Exit" option, left, "Find On Map" option, right. Tip: You can...

101 Find Map Places or Points of Interest (POI) 1. Press WPT , press ↓ or ↑ to select a map place or POI category, then press ENT . (To narrow your search, press → then press ↓ or ↑ to select a subcategory before pressing ENT .) You will be given two options; Search By Name or By Nearest. Find Waypo...

102 the lower selection list by pressing ENT , then press ↓ or ↑ to select a POI from the list, then press ENT to call up the POI's Waypoint Infor- mation screen. Find by Name option, left, Find by Name menu, right. 4. When the POI's Waypoint Information screen is displayed, you canchoose to "Go...

103 Find Streets command, left, Find Streets menu, right. 2. You must first fill in a street name in the First Street dialog box. Press ENT to display the Find By Name menu. There are two options: a. You can spell out the street in the top selection box. Press ↑ or ↓ to change the first letter, then...

104 At left, the Find Streets menu with the Find First Street command highlighted. At right, Streets Found list. 4. The Map Page appears, with the cursor pointing to the found street. Map Page showing results of a street search. The cursor points to the located street. If you want to navigate to the...

105 spell out the street in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then press ENT | ENT . B. Or you can jump down to the lower box and pick a street from the selection list . Press ENT ,...

106 7. The Map Page appears, with the cursor pointing to the found intersec-tion. The intersection in our example is shown in the following figure. Map Page showing results of an intersection search. The cursor points to the located intersection. If you want to navigate to the found intersection, ju...

107 Calculating message, left, and list of the nearest waypoints, right. 4. To see location information on the closest (highlighted) waypoint,press ENT and the Waypoint Information screen appears. (If you wanted to, you could select another waypoint from the list with the ↑ or ↓ keys.) a. To navigat...

108 5. If you're looking by name , there are two options: a. You can spell out the name in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then press ENT | ENT . B. Or you can jump down to the lo...

109 Section 7: Supplemental Material Datums Used by This Unit WGS 1984Default AdindanMean for Ethiopia,Sudan AdindanBurkina Faso AdindanCameroon AdindanEthiopia AdindanMali AdindanSenegal AdindanSudan AfgooyeSomalia Ain el Abd 1970Bahrain Ain el Abd 1970Saudi Arabia Anna 1 Astro 1965Cocos Islands An...

113 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi-cations Commission (FCC) Rules. Operation is subject to the fol-lowing two conditions: (1) this device may not cause harmful in-terference, and (2) this device must accept any interference re-ceived, including interfere...

115 Index A Accessories, 1, 3, 4, 6, 11, 14, 15, 19, 30, 48, 95 Sec. 2, Installation & Accessories, 11 Alarm Clock, 61Alarms, 23, 33, 46, 48, 59, 65, 66, 74Anchor Alarm, 65, 66Antenna, 1, 3, 4, 11, 12, 15, 16, 17, 33, 34, 113 Arrival Alarm, 33, 46, 48, 59, 65, 66, 74 B Backlights / Lighting, 2, ...

118 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Eagle Electronics, a division of LEI, the manufac-turer of this product. "You" or "your" refers to the first person who purchasesthe product as a consumer item for personal, family, or household use...

119 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufac-turer of this product. "You" or "your" refers to the first person who purchases this productas a consumer item for personal, family, o...

120 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert serviceand genuine Eagle replacement parts. If you're in the United Statesand you have technical, return or repair questions, please contact theFactory Customer Service Department. Before any produ...

Accessory Ordering Informationfor all countries To order Eagle accessories such as computer cables or MMC cards,please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumerelectronics should be able to assis...

Visit our web site: www.eaglesonar.com Eagle Pub. 988-0143-741 © Copyright 2003 All Rights Reserved Printed in USA 121903 Eagle Electronics 