Dynex DX-DTVMFP23 - Manuals

Page 2 - Safety information and specifications; Do not use this; We’re here for you

2 Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS CAUTION: Do not use this product for any purpose not explicitly specified by Dynex.Improper installation may cause property damage or personal injury. If you do not understand these directions, or have do...

Page 3 - Tools needed; Package contents

DX-DTVMFP23 3 Tools needed You will need the following tools to assemble your new TV wall mount: ard ware Package contents Make sure that you have all the hardware necessary to assemble your new TV wall mount: A Wall Plate (1) C Right TV Bracket (1) B Left TV Bracket (1) D Plastic covers (2) Edge-to...

Page 4 - TV Hardware Bag; Label

4 TV Hardware Bag Label Hardware Qty. E 4 F 4 G 8 H 4 I 4 J 4 K 4 L 4 M4 × 12 mm screw M4 × 35 mm screw M4 washer M6/M8 washer Universal spacers M6 × 12 mm screw M6 × 35 mm screw M8 × 16 mm screw Label Hardware Qty. M 4 N 4 O 4 P 4 Q 4 1 M8 × 20 mm screw M8 × 36 mm screw Lag bolt washer 5/16" × ...

Page 5 - Installation instructions; Flat back

DX-DTVMFP23 5 Installation instructions STEP 1- Determine whether your TV has a flat back or an irregular or obstructed back 1 Carefully place your TV face-down on a cushioned, clean surface to protect the screen. 2 If your TV has a table-top stand attached, remove the stand. See the documentation t...

Page 7 - Fit the plastic covers (; You’ll need

DX-DTVMFP23 7 STEP 3 - Attaching the plastic covers to the wall plate 1 Fit the plastic covers ( D ) over the ends of the wall plate ( A ). 2 For a flat back TV, go to “STEP 4 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on page 8.-OR-For an irregular or obstructed back, go t...

Page 8 - Note

8 STEP 4 - Option 1: Attaching the mounting hardware to TVs with a flat back Note : If you plan to use a 5° tilt with a larger TV (42”+), we suggest using spacers with the mounting brackets so that the bottom of the TV does not touch the wall. 1 Align the left and right TV brackets ( B and C ) with ...

Page 11 - Option 1: Installing on a wood stud wall; CAUTION

DX-DTVMFP23 11 STEP 6 - Option 1: Installing on a wood stud wall Note : Any drywall covering the wall must not exceed 5/8" (16 mm). 1 Locate the studs. Verify the centers of the studs with an edge-to-edge stud finder. 2 Align the wall plate ( A ) at the height you determined in the previous step...

Page 12 - Mount the wall plate directly onto the concrete surface.

12 STEP 6 - Option 2: Installing on a solid concrete or concrete block wall CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount the wall plate directly onto the concrete surface. 1 Align the wall plate ( A ) at the height you determined in the previo...

Page 14 - STEP 7 - Mounting the TV to the wall plate; Place the TV brackets (

14 STEP 7 - Mounting the TV to the wall plate 1 Place the TV brackets ( B and C ) into the slotted flanges of the wall plate ( A ). 2 Push the bottom of the TV toward the wall until the spring self-locking system clicks into place. Congratulations, you have finished the installation. Time to watch s...

Page 15 - If you ever need to remove the TV from the wall plate

DX-DTVMFP23 15 If you ever need to remove the TV from the wall plate 1 Grasp the TV by the bottom edge, then pull down on the locking cords and pull the bottom of the TV out from the wall. 2 Release the locking cords and lift the top of the TV from the wall bracket. Pull down to unlatch. HEAVY! You ...