Dynex dx-drtvm112 - Manuals

Page 2 - Safety information and specifications; Do; We’re here for you

2 Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS CAUTION: Do not use this product for any purpose not explicitly specified by Dynex.Improper installation may cause property damage or personal injury. If you do not understand these directions, or have do...

Page 3 - Tools needed

DX-DRTVM112 3 Tools needed You will need the following tools to assemble your new TV wall mount: ardware Edge-to-edge stud finder Pencil Level Phillips screwdriver Socket wrench with 7/16" (12 mm) socket or adjustable wrench Measuring tape Drill 1/8" (3 mm) wood drill bit for wood stud wall ...

Page 4 - Package contents; TV Hardware Bag; Label

4 Package contents Make sure that you have all of the hardware necessary to assemble your new TV wall mount: A TV Bracket (1) B Wall Plate (1) C Bracket Extensions (2) D Wall mount template (1) TV Hardware Bag Top Haut Parte superior DX-TVM111 Template • Gabarit • Plantilla Tools Needed Outils néces...

Page 5 - Installation instructions; Determining the hole pattern on your TV; If you need to install the extension brackets (; You’ll need

DX-DRTVM112 5 Installation instructions STEP 1 - Determining the hole pattern on your TV 1 Carefully place your TV screen face down on a cushioned, clean surface to protect the screen from damage and scratches. 2 If your TV has a table top stand attached, remove the stand. See the documentation that...

Page 6 - Flat back; your TV. You will need spacers when assembling the wall mount.; Irregularly-shaped back; Remove the TV bracket (

6 STEP 2 - Determine whether your TV has a flat, irregular, or obstructed back 1 Temporarily lay the TV bracket ( A ) and adapters ( C ), if necessary, on the back of your TV. 2 Align the screw holes in the TV bracket with the mounting screw holes on your TV. 3 Identify which type of back your TV ma...

Page 7 - STEP 3 - Select screws and spacers; For an irregular or obstructed TV back, use the following spacers:; To avoid potential personal; ) for an irregular or obstructed TV back.

DX-DRTVM112 7 STEP 3 - Select screws and spacers 1 Select the hardware for your TV (screws and spacers). A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back of the TV.)Select one of the following ty...

Page 8 - Align the TV bracket (

8 STEP 4 - Option 1: Attaching the mounting hardware to TVs with a flat back 1 Align the TV bracket ( A ) with the screw holes on the back of the TV. 2 Install washers ( G ), and screws ( E ) into the holes in the back of the TV. 3 Tighten the screws until they are snug against the TV bracket. Do no...

Page 11 - Option 1: Installing on a wood stud* wall; Note

DX-DRTVM112 11 STEP 6 - Option 1: Installing on a wood stud* wall Note : Any drywall covering the wall must not exceed 5/8" (16 mm). 1 Locate the stud. Verify the center of the stud with an edge-to-edge stud finder. 2 Align the wall plate template ( D ) at the height you determined in the previo...

Page 12 - blocks. Mount the wall plate directly onto the concrete surface.

12 STEP 6 - Option 2: Installing on a solid concrete* or concrete block wall CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount the wall plate directly onto the concrete surface. 1 Align the wall plate template ( D ) at the height you determined in ...

Page 13 - STEP 7 - Mounting the TV to the wall plate; Place the TV bracket (

DX-DRTVM112 13 STEP 7 - Mounting the TV to the wall plate 1 Place the TV bracket ( A ) into the slotted flanges of the wall plate ( B ). The TV can be mounted either (1) vertically, or (2) with a 6° tilt. 2 Lock the TV and bracket assembly to the wall plate by rotating the lock into the flange slot....