Dukane 8107WIB - Manuals - manualsarea.com

Page 2 - Initial set signals; and H POSITION in the IMAGE menu.; Data

2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Act...

Page 3 - Connection to the ports; NOTICE; COMPUTER IN1; MONITOR OUT; D-sub 15pin mini shrink jack

3 Connection to the ports Connection to the ports NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN1 or IN2 can be output from the MONITOR OUT port. COMPUTER IN1 COMPUTER IN2 HDMI USB T...

Page 4 - VIDEO

4 D S-VIDEO Mini DIN 4pin jack • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz) Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator 2 Brightness signal, 1.0Vp-p, 75Ω terminator 3 Ground 4 Ground Connection to the por...

Page 5 - AUDIO IN2

5 COMPUTER IN1 COMPUTER IN2 HDMI USB TYPE B S-VIDEO VIDEO AUDIO OUT AUDIO IN3 AUDIO IN1 AUDIO IN2 MIC MONITOR OUT CONTROL USB TYPE A DC5V 0.5A LAN L R R L Connection to the ports (continued) G AUDIO IN1, H AUDIO IN2 Ø3.5 stereo mini jack• 200 mVrms, 47kΩ terminator AUDIO IN3 I R, J L RCA jack x2• 20...

Page 7 - To input component video signal to COMPUTER IN ports; To input component video signal to the; or; and

7 Connection to the ports (continued) To input component video signal to COMPUTER IN ports ex. To input component video signal to the COMPUTER IN1 or IN2 port of the projector, use a RCA to D-sub cable or adapter. For about the pin description of the required cable or adapter, refer to the descripti...

Page 8 - RS-232C Communication; Connection; Turn off the projector and the computer.; CONTROL; CONTROL; port

8 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( & 17 ). Connectio...

Page 9 - Communication settings; table

9 RS-232C Communication (continued) Communication settings 1. Protocol 19200bps,8N1 2. Command format ("h" shows hexadecimal) Byte Number 0 1 2 3 4 5 6 7 8 9 10 11 12 Command Action Header Data Header code Packet Data size CRC flag Action Type Setting code L H L H L H L H L H L H <SET>...

Page 10 - NOTE

10 RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specified item by [Type], and it returns the c...

Page 11 - LAN

11 Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( & 17 ). Connection 1. Turn off the projecto...

Page 12 - Communicaion Port; The following two ports are assigned for the command control.; Port Settings; Security Settings

12 Communicaion Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (Po...

Page 13 - Command control settings; Header; Refer to RS-232C Communication command format

13 Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the sam...

Page 15 - SERVICE - COMMUNICATION in the User's Manual - Operating Guide; Network Bridge Communication

15 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communicaton, an external device that is connected with this projector by RS-232C communication can be controlled from the computer as a network terminal. For details, see the 6. Network Br...

Page 16 - For communication setting, use the OPTION - SERVICE - COMMUNICATION; Transmission method

16 Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu. ( & OPTION menu - SERVICE - COMMUNICATION in the User's Manual - Operating Guide ) Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (fixed) PARITY NONE/ODD/EVEN ...

Page 31 - PJLink command

31 PJLink command PJLink command POWR Power Contorol 0 = Standby1 = Power On POWR ? Power Status inquiry 0 = Standby1 = Power On2 = Cool Down INPT Input Source selection 11 = COMPUTER IN 112 = COMPUTER IN 222 = S-VIDEO23 = VIDEO31 = HDMI41 = USB TYPE A51 = LAN52 = USB TYPE B INPT ? Input Source inqu...