Dodge 2008 Nitro - Manuals

WARNINGS AND CAUTIONS This manual contains WARNINGS against operatingprocedures, which could result in an accident or bodilyinjury. It also contains CAUTIONS against procedures,which could result in damage to your vehicle. If you donot read this entire manual, you may miss importantinformation. Obse...

VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle couldseriously affect its roadworthiness and safety andmay lead to an accident resulting in serious injury ordeath. 8 INTRODUCTION

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .12 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 m Sentry Key . . . . . . . . . . . . . . . . . . . . . . . ....

A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks witheither side up. The keys for your new vehicle are enclosed in a plasticbag with the key code number on it. If you received yourkeys without the bag, ask your dealer to give you thenumber. The key code can also be obtained...

WARNING! Never leave children alone in a vehicle. Leavingchildren in a vehicle unattended is dangerous for anumber of reasons. A child or others could be seri-ously or fatally injured. Don’t leave the keys in theignition. A child could operate power windows,other controls, or move the vehicle. CAUTI...

Key-In-Ignition Reminder If you open the driver’s door and the key is in theignition, a chime will sound to remind you to remove thekey. NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACCposition. SENTRY KEY The Sentry Key Immobilizer System prevents un...

If the Vehicle Security Alarm Indicator Light turns onduring normal vehicle operation (vehicle running forlonger than 10 seconds), it indicates that there is a fault inthe electronics. Should this occur, have the vehicle ser-viced as soon as possible. NOTE: • The Sentry Key Immobilizer System is not...

The new Sentry Key is programmed. The Keyless EntryTransmitter will also be programmed during this pro-cedure. Repeat this procedure to program up to 8 keys. If you donot have a programmed sentry key, contact your dealerfor details. NOTE: If a programmed key is lost, see your dealer to have all rema...

To Release the Steering Wheel Lock Insert the key in the ignition and turn the wheel slightlyto the right or left to disengage the lock. NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right todisengage it. If you turned the wheel to the left to...

REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors andliftgate or activate the panic alarm from distances up to23 feet (7 meters) using your key fob. The key fob doesnot need to be pointed at the vehicle to activate thesystem. NOTE: • For the remote starting feature (if equipped...

On electronic vehicle information center (EVIC) equipped vehicles, refer to “Remote Key Unlock,” under“Personal Settings (Customer Programmable Features),”under “Electronic Vehicle Information Center (EVIC)” inSection 4 of this manual On non-EVIC equipped vehicles, perform the followingsteps: 1. Pre...

1. Press and hold the “Unlock” button on a programmed(i.e. functional) key fob for at least 4 seconds, but notlonger than 10 seconds. Then, press and hold the “Lock”button while still holding the “Unlock” button. 2. Release both buttons at the same time. 3. Test the feature from outside the vehicle ...

During the Panic Mode, the door locks and remotekeyless entry systems will function normally. Panic modewill not disarm the security system on vehicles soequipped. Programming Additional Transmitters Refer to SENTRY KEY “Customer Key Programming.”in this section. NOTE: If you do not have a programme...

2. Remove and replace the batteries. Avoid touching thenew batteries with your fingers. Skin oils may causebattery deterioration. If you touch a battery, clean it withrubbing alcohol. 3. To assemble the key fob case, snap the two halvestogether. NOTE: If the key fob is equipped with a screw, reinsta...

To remote start your vehicle, press and release the“Remote Start” button on the key fob twice within threeseconds. To indicate that the vehicle is about to start, theparking lights will flash and the horn will sound briefly(if programmed). Once the engine starts it will run for 15 minutes. Tocancel ...

The vehicle can be started remotely a maximum of twotimes consecutively. The vehicle is also allowed a maxi-mum of one failed start, where the remote start sequencewas initiated but the engine stopped cranking withoutstarting. Following either of these conditions, or if theVehicle Security Alarm (if...

Manual Door Locks Use the manual door lock plunger to lock the doors frominside the vehicle. If the plunger is down when the dooris closed, the door will lock. Therefore, make sure thekeys are not inside the vehicle before closing the door. WARNING! • For personal security and safety in the event of...

Power Door Locks A door lock switch is on each front door panel. Press thisswitch to lock or unlock the doors. If you press the power door lock switch while the key isin the ignition, and any front door is open, the power locks will not operate. This prevents you from acciden-tally locking your keys...

Automatic Door Locks ProgrammingThe Automatic Door Locks feature can be enabled ordisabled as follows: For vehicles equipped with a Electronic Vehicle Informa-tion Center (EVIC), refer to “Personal Settings (CustomerProgrammable Features)” under “Electronic Vehicle In-formation Center (EVIC)” in Sec...

Child-Protection Door Lock System (Rear Doors) Insert the tip of the ignition key into the lock and rotateto the lock or unlock position. WARNING! Avoid trapping anyone in a vehicle in a collision.Remember that the rear doors can only be openedfrom the outside when the child protection locks areenga...

WINDOWS Power Windows The power window controls are located on the driver’sdoor trim panel. There is a single switch on the frontpassenger door/rear doors which operates the frontpassenger/rear passenger door windows. The windowcontrols will operate only when the ignition switch is inthe ON or ACCES...

Wind Buffeting Wind buffeting can be described as the perception ofpressure on the ears or a helicopter type sound in theears. Your vehicle may exhibit wind buffeting with thewindows down, or the sunroof (if equipped) in certainopen or partially open positions. This is a normal occur-rence and can b...

LIFTGATE The vacuum fluorescent (VF) display located in theodometer area displays the word “GATE” as an indica-tion of when the liftgate is not completely closed. Whenthe vehicle is not moving, and the liftgate is not com-pletely closed, the VF display will show the word“GATE.” On EVIC equipped vehi...

WARNING! Driving with the liftgate open can allow poisonousexhaust gases into your vehicle. You and your pas-sengers could be injured by these fumes. Keep theliftgate closed when you are operating the vehicle. OCCUPANT RESTRAINTS Some of the most important safety features in yourvehicle are the rest...

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back andadjust the seat. 2. The seat belt latch plate is above the back of your seat.Grasp the latch plate and pull out the belt. Slide the latchplate up the webbing as far as necessary to make the beltgo around yo...

3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.” WARNING! A belt that is buckled into the wrong buckle will notprotect you properly. The lap portion could ride too highon your body, possibly causing internal injuries. Alwaysbuckle your belt into...

4. Position the lap belt across your thighs, below yourabdomen. To remove slack in the lap portion, pull up abit on the shoulder belt. To loosen the lap belt if it is tootight, tilt the latch plate and pull on the lap belt. A snugbelt reduces the risk of sliding under the belt in acollision. WARNING...

6. To release the belt, push the red button marked PRESSon the buckle. The belt will automatically retract to itsstowed position. If necessary, slide the latch plate downthe webbing to allow it to retract fully. WARNING! A frayed or torn belt could rip apart in a collision andleave you with no prote...

As a guide, if you are shorter than average, you willprefer a lower position, and if you are taller than average,you’ll prefer a higher position. When you release theanchorage, try to move it up or down to make sure thatit is locked in position. Automatic Locking Mode — If Equipped In this mode, the...

WARNING! • The belt and retractor assembly must be replacedif the seat belt assembly “automatic locking retrac-tor” feature or any other seat belt function is notworking properly when checked according to theprocedures in the Service Manual. • Failure to replace the belt and retractor assemblycould ...

Driver And Front Passenger SupplementalRestraint Systems (SRS) This vehicle has airbags for both the driver and rightfront passenger as a supplement to the seat belt restraintsystems. The driver’s front airbag is mounted in thesteering wheel. The passenger side airbag is mounted inthe instrument pan...

This vehicle is equipped with window bags to protect thedriver, front, and rear passengers sitting next to a win-dow. They are located above the side windows. Theircovers are also labeled SRS/AIRBAG. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag depl...

• Front Remote Acceleration Sensors • Seat Track Position Sensors (STPS) — If Present • Driver and Front Passenger Seat Belt Pretensioner • Driver and Front Passenger Seat Belt Retractors • Occupant Classification System (OCS) — Front Pas-senger Seat Only − Occupant Classification Module − Passenger...

NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. • The Passenger Airbag Disable (PAD) Indicator Light(an amber light located in the center of the instrumentpanel) tells the driver and front passenger when thefront passenger airbag is t...

of nontoxic gas is generated to inflate the side curtainairbag. The inflating side curtain airbag pushes theoutside edge of the headliner out of the way andcovers the window. The airbag inflates in about 30milliseconds (about one quarter of the time it takes toblink your eyes) with enough force to i...

WARNING! Unapproved modifications or service procedures tothe front passenger seat assembly, its related compo-nents, or seat cover may inadvertently change theairbag deployment in case of a frontal crash. Thiscould result in death or serious injury to the frontseat passenger if the vehicle is invol...

Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to failwhen you need it. You could be injured if the airbag system is notthere to protect you. Do not modify the components or wiring,including adding any kind of badges or stickers to the steerin...

• Cruise control status • Traction/stability control status • Tire pressure monitoring system status Child Restraint Everyone in your vehicle needs to be buckled up all thetime — babies and children, too. Every state in the UnitedStates and all Canadian provinces require that smallchildren ride in p...

Infants and Child Restraints • Safety experts recommend that children ride rearward-facing in the vehicle until they are at leastone year old and weigh at least 20 lbs (9 kg). Two typesof child restraints can be used rearward-facing: infantcarriers and “convertible” child seats. • The infant carrier...

The belt-positioning booster seat is for children weighingmore than 40 lbs (18 kg), but who are still too small to fitthe vehicle’s seat belts properly. If the child cannot sitwith knees bent over the vehicle’s seat cushion while thechild’s back is against the seat back, they should use abelt-positi...

belt. However, any seat belt system may loosen withtime, so check the belt occasionally and pull it tight ifnecessary. If the seat belt has a automatic locking retractor, it willhave a distinctive label. Pull the belt from the retractoruntil there is enough to allow you to pass through thechild rest...

WARNING! An incorrectly anchored tether strap could lead toincreased head motion and possible injury to thechild. Use only the anchor positions directly behindthe child seat to secure a child restraint top tetherstrap. Transporting PetsAirbags deploying in the front seat could harm your pet.An unres...

UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .83 ▫ Automatic Dimming Mirror — If Equipped . . . .84 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . ....

▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . . 145 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . . 146 ▫ Venting Sunroof - Express . . . . . . . . . . . . . . . 146 ▫ Sunshade Operation . . . . . . . . . . . . . . . . . . . 146 ▫ Wind Buffeting . . . . . . . . . . . . . . ....

MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the viewthrough the rear window. A two-point pivot system allows for horizontal andvertical adjustment of the mirror. Annoying headlight glare can be reduced by moving thesmall control under the mirror to the night position(t...

Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for annoying head-light glare from vehicles behind you. You can turn thefeature on or off by pressing the button at the base of themirror. A light in the button will indicate when thedimming feature is activated. CAUTION! T...

WARNING! Vehicles and other objects seen in the right sideconvex mirror will look smaller and farther awaythan they really are. Relying too much on your rightside mirror could cause you to collide with anothervehicle or other object. Use your inside mirror whenjudging the size or distance of a vehic...

Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To usethe mirror, rotate the sun visor down and swing themirror cover upward. The lights will turn on automati-cally. Closing the mirror cover will turn off the light. Sun Visor “Slide-Out” FeatureThe sun vis...

The radio display will be used for visual prompts fromthe UConnect t system such as 9 CELL 9 or caller ID on certain radios. Operation Voice commands can be used to operate the UConnect t system and to navigate through the UConnect t menu structure. Voice commands are required after mostUConnect t s...

To activate the UConnect t system from idle, simply press the “Phone” button and follow audible prompts fordirections. All UConnect t system sessions begin with a press of the “Phone” button on the radio control head. Cancel CommandAt any prompt, after the beep, you can say 9 Cancel 9 and you will b...

Phone Call Features The following features can be accessed through theUConnect t system if the feature(s) are available on your cellular service plan. For example, if your cellular serviceplan provides three-way calling, this feature can beaccessed through the UConnect t system. Check with your cell...

hold may not become active automatically. This is cellphone dependent. To bring the call back from hold, pressand hold the “Phone” button until you hear a singlebeep. Redial • Press the “Phone” button to begin. • After the 9 Ready 9 prompt and the following beep, say 9 Redial. 9 • The UConnect t sys...

• You can also press the “Voice Recognition” buttonanytime while the list is being played, and then choosethe phone you wish to delete. Things You Should Know About Your UConnect T System UConnect t Tutorial To hear a brief tutorial of the system features, press the“Phone” button and say “UConnect t...

• Even though international dialing for most numbercombinations is supported, some shortcut dialingnumber combinations may not be supported. • In a convertible vehicle, system performance may becompromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: •...

General Information This device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions: • This device may not cause harmful interference. • This device must accept any interference received,including interference that may cause undesired...

WARNING! Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seat couldcause you to lose control. The seat belt might not beproperly adjusted and you could be injured. Adjustany seat only while the vehicle is parked. Front Seat Adjustment — Recline To adjust the seat...

WARNING! Do not ride with the seatback reclined so that the seatbelt is no longer resting against your chest. In acollision you could slide under the seat belt and beseriously or even fatally injured. Use the reclineronly when the vehicle is parked. 6–Way Driver’s Power Seat with Manual Recliner The...

Fold Flat Front Passenger Seat The front passenger seat can be folded flat to allow forextended cargo space. Pull up on the lever to fold downthe seat back. Head Restraints Head restraints can reduce the risk of whiplash injury inthe event of impact from the rear. Adjustable headrestraints should be...

indicate the level of heat in use. Two LEDs are illumi-nated for high, one for low, and none for off. Pressing theswitch once will select high-level heating. Pressing the switch a second time will select low-levelheating. Pressing the switch a third time will shut theheating elements off. When high-...

NOTE: Prior to folding the rear seat, it may be necessary to reposition the front seat to its mid-track position. Also, be sure that the front seats are fully upright andpositioned forward. This will allow the rear seat to folddown easily. WARNING! • It is extremely dangerous to ride in a cargo area...

To Lower Rear Seat 1. Locate the release strap on the lower outboard side ofeach rear seatback. 2. Pull the release strap (toward the front of the vehicle). 3. Fold the rear seat completely forward. 4. If desired, push down on the seatback to lock it in thefolded position. To Raise Rear SeatIf locke...

TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pullthe hood release lever located under the left side of theinstrument panel. Then push the safety latch lever to the right. It is locatedbetween the grille and hood opening left of the center. Hood Release Lever Under...

To prevent possible damage, do not slam the hood toclose it. Use a firm downward push at the center frontedge of the hood to ensure that both latches engage.Never drive your vehicle unless the hood is fully closed,with both latches engaged. NOTE: Ensure hood prop rod is fully seated into clip before...

Multi-Function Control Lever The multi-function control lever controls the operation ofthe parking lights, headlights, headlight beam selection,passing light, fog lights, instrument panel light dimming,and turn signals. Parking Lights, Instrument Panel Lights, andHeadlights Turn the end of the multi...

To change the brightness of the instrument panel lights,rotate the center portion of the multi-function controllever up or down. NOTE: If the driver’s door is left open, and the head- lights or parking lights are left on, the “High BeamIndicator Light” will flash and a chime will sound. Lights-On Re...

Turn Signals Move the multi-function control lever up or down andthe arrows on each side of the instrument cluster flash toshow proper operation of the front and rear turn signallights. You can signal a lane change by moving the leverpartially up or down without moving beyond the detent. If either l...

Intermittent Wiper System Use the intermittent wiper when weather conditionsmake a single wiping cycle, with a variable pause be-tween cycles, desirable. Move the lever to the DELAYposition, then select the delay interval by turning the endof the lever. The delay can be regulated from a maximumof ap...

If the lever is pulled while in the OFF position, the wiperswill operate for as long as the lever is held plus two wipecycles, then turn OFF. Mist Feature Push down on the wiper lever to activate a single wipe toclear off road mist or spray from a passing vehicle. Aslong as the lever is held down, t...

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the acceleratoroperation at speeds greater than 25 mph (40 km/h). Electronic Speed Control Operation The speed control lever is located on the right side of thesteering wheel. To Activate Push the ON/OFF button. The CRUISE i...

To Set At A Desired Speed When the vehicle has reached the desired speed, pressdown on the lever and release. Release the acceleratorand the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever. To Deact...

Tapping the “SET DECEL” button once will result in a 1mph (2 km/h) speed decrease. Each time the button istapped, speed decreases. NOTE: The Speed Control system has been designed to shut down if multiple speed control switch functions areoperated simultaneously in order to ensure proper op-eration....

On steep hills a greater speed loss or gain may occur soit may be preferable to drive without speed control. ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronicbrake control system that includes ABS (Anti-Lock BrakeSystem), TCS (Traction Control System), BAS (BrakeAs...

• Oversteer - when the vehicle is turning more thanappropriate for the steering wheel position. • Understeer - when the vehicle is turning less thanappropriate for the steering wheel position. ESP/TCS Indicator Light The 9 ESP/TCS Indicator Light 9 located in the instrument cluster, starts to flash ...

ESP OnThis is the normal operating mode for ESP in 2WD, 4WDPart Time, 4WD Full Time, and on 2WD vehicles. When-ever the vehicle is started, the ESP system will be in thismode. This mode should be used for most all drivingsituations. ESP should only be turned off for specificreasons as noted below. P...

situation requiring ESP to be switched to the “Partial Off”mode is overcome, turn ESP back on by momentarilydepressing the “ESP OFF” switch. This may be donewhile the vehicle is in motion. ESP/BAS Warning Lamp The malfunction indicator lamp for the ESP iscombined with BAS. The “ESP/BAS WarningLamp” ...

The HomeLink t buttons that are located in the headliner or sun visor designate the three different HomeLink t channels. NOTE: HomeLink t is disabled when the Vehicle Secu- rity Alarm is active. WARNING! Your motorized door or gate will open and close whileyou are training the Universal Transceiver....

WARNING! Vehicle exhaust contains carbon monoxide, a danger-ous gas. Do not run your vehicle in the garage whiletraining the transceiver. Exhaust gas can cause seri-ous injury or death. Programming HomeLink T Before You BeginIf you have not trained any of the HomeLink t buttons, erase all channels b...

6. Firmly press and release the “learn” or “training”button. The name and color of the button may vary bymanufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmedHomeLink t button twice (ho...

Similar to this Canadian law, some U.S. gate operators aredesigned to “time-out” in the same manner. It may be helpful to unplug the device during the cyclingprocess to prevent possible overheating of the garagedoor or gate motor. If you are having difficulties programming a garage dooropener or a g...

1. This device may not cause harmful interference 2. This device must accept any interference that may bereceived including interference that may cause undesiredoperation NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications notexpressly approved by th...

sunroof will automatically retract. Remove the obstruc-tion if this occurs. Next, press the switch forward andrelease to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing,press the switch forward and hold. This allows thesunroof to move towards the clo...

Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to cleanthe glass panel. ELECTRICAL POWER OUTLET This vehicle has two auxiliary power outlets that canprovide up to 20 Amps of current for accessories de-signed for use with the standard power outlet adapters.The front power outlet...

The rear power outlet (if equipped) is located in the leftrear cargo area. Electrical Outlet Use With Engine Off WARNING! • Many accessories that can be plugged in draw powerfrom the vehicle’s battery, even when not in use (i.e.cellular phones, etc.). Eventually, if plugged in longenough, the vehicl...

POWER INVERTER There is a 110–volt, 150–watt inverter outlet located onthe back of the center console to convert DC current toAC current. This outlet can be used to power smallappliances and electronics. Press the switch located in the center stack lower switchbank to turn the power on to the outlet...

NOTE: Due to build in overload protection the inverter will shut down if the power rating is exceeded. WARNING! To Avoid Serious Injury or Death: • Do not use a 3—Prong Adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If thi...

CUP HOLDERS In the center console there are two cup holders for thefront seat passengers. The rear passengers have cup holders at the rear of thecenter console. Front Cup Holders Rear Cup Holders UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 3

STORAGE Front Storage Compartment The front storage compartment (located on the left side ofthe instrument panel) can hold cell phones, PDA’s, andother small items. Console Storage Compartment To open, press the latch and lift the cover. Front Storage Compartment Center Console 152 UNDERSTANDING THE...

The center console has a removable storage tray, whichcan hold cell phones, PDA’s, and other small items. CARGO AREA FEATURES Cargo Light The cargo area light is activated by opening the liftgate,opening any door, or by rotating the dimmer control onthe multi-function control lever to the extreme to...

WARNING! The weight and position of cargo and passengers canchange the vehicle center of gravity and vehiclehandling. To avoid loss of control resulting in per-sonal injury, follow these guidelines for loading yourvehicle: • Do not carry loads which exceed the load limitsdescribed on the label attac...

Rear Cargo Slide Out System (LOAD N GO T ) — If Equipped The sliding cargo load floor (LOAD N GO t ) slides back and forth on steel tracks for convenience. The maximumload capacity is 400 lbs (181 kg). The floor panel can stopevery 2 inches (50 mm) when the handle is released, tolock the panel in po...

3. Pull out the sliding panel. 4. Squeeze the right hand release handle to slide thepanel back into the vehicle. REAR WINDOW FEATURES Rear Window Wiper/Washer — If Equipped A rotary ring switch on the control lever (located on theright side of the steering column), controls operation ofthe rear wipe...

If the rear wiper is operating when the ignition is turnedOFF, the wiper will automatically return to the “Park”position. When the vehicle is restarted, the wiper willresume function at whichever position the switch is setat. If the swing gate flip-up window is open or the swinggate is open, connect...

Adding Washer FluidThe fluid reservoir for the windshield washers and therear window washer is shared. It is located in the front ofthe engine compartment, and should be checked for fluidlevel at regular intervals. Fill the reservoir with wind-shield washer solvent (not radiator antifreeze) and oper...

ROOF LUGGAGE RACK— NON FUNCTIONAL The tie loops provided in the Roof Ditch Applique can beused to help tie down cargo; however, metal rails/crossbars should always be used whenever cargo is placed on the roof. Tie loops should not be used on theirown to attach luggage to the Roof Ditch Applique. The...

INSTRUMENT PANEL AND CONTROLS CONTENTS m Instrument Panel And Controls . . . . . . . . . . . . . 166 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 167 m Instrument Cluster Description . . . . . . . . . . . . . 168 m Compass And Trip Computer — If Equipped . . . 180 ▫ Control Butto...

▫ System Activation . . . . . . . . . . . . . . . . . . . . . 227 ▫ Electronic Serial Number/Sirius IdentificationNumber (ENS/SID) . . . . . . . . . . . . . . . . . . . . 228 ▫ Selecting Satellite Mode . . . . . . . . . . . . . . . . . 228 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . ...

INSTRUMENT CLUSTER INSTRUMENT PANEL AND CONTROLS 167 4

INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge The fuel gauge shows level of fuel in tank whenignition switch is in the ON position. 2. Fuel Cap Indicator This symbol indicates the side of the vehiclewhere the fuel cap is located. 3. Temperature Gauge The temperature gauge indicates engine coolanttemp...

16. Electronic Stability Program (ESP) IndicatorLight/Traction Control System (TCS) Indicator Light The yellow ESP indicator light in the speedom-eter area illuminates with the key in the igni-tion switch turned to the ON/RUN position. Itshould go out with the engine running. The 9 ESP/TCS Indicator...

26. Odometer/Trip OdometerThe odometer shows the total distance the vehicle hasbeen driven. The trip odometer shows individual trip mileage. Totoggle between the odometer and the trip odometer,press the Odometer/Trip Odometer Button. To reset theTrip Odometer, press and hold the button while in trip...

COMPASS AND TRIP COMPUTER — IFEQUIPPED The Compass/Trip Computer features a driver- interactive display (displays information on outside tem-perature, compass direction, and trip information). It islocated on the lower left part of the cluster below the fueland engine temperature gauge, and the tach...

• Loose Fuel Cap (gASCAP) These messages can be manually turned off by pressingthe right button (on the instrument cluster). Control Buttons Press and release the odometer/trip odometer reset but-ton (right side of the instrument cluster) to access thecompass/trip computer displays. Display Button I...

• Right Front Low Pressure (with a single chime). Referto “Tire Pressure Monitoring System” in Section 5 ofthis manual. • Right Rear Low Pressure (with a single chime). Referto “Tire Pressure Monitoring System” in Section 5 ofthis manual. • Check TPM System (with a single chime). Refer to“Tire Press...

3. Turn the ignition switch to the OFF/LOCK position. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did notreset. If necessary repeat this procedure. Trip Functions Press and release the MENU button until one of thefollowing Trip Functions dis...

• When the DTE value is less than 30 miles (48 km)estimated driving distance, the DTE display willchange to a text display of 9 LOW FUEL. 9 This display will continue until the vehicle runs out of fuel. Addinga significant amount of fuel to the vehicle will turn offthe 9 LOW FUEL 9 text and a new DT...

objects) until the “CAL” indicator displayed in the EVICturns off. The compass will now function normally. Manual Compass CalibrationIf the compass appears erratic and the “CAL” indicatordoes not appear in the EVIC display, you must put thecompass into the Calibration Mode manually as follows: 1. Tu...

1. Turn the ignition switch ON. 2. Press and hold the compass button for approximately2 seconds. 3. Press the SCROLL button until “Compass Variance”message and the last variance zone number displays inthe EVIC. 4. Press and release FUNCTION SELECT button untilthe proper variance zone is selected acc...

• Phone status: idle, voice mail, roaming, batterystrength, and signal strength in increments of 20percent. • Call status: Incoming call, connecting, connected, airtime in minutes and seconds, call ended, call failed,roaming, and no phone connection. • UConnect Active. • Caller ID phone number displ...

Use the SCROLL button to display one of the followingchoices: LanguageWhen in this display you may select one of five lan-guages for all display nomenclature, including the tripfunctions and the navigation system (if equipped). Pressthe FUNCTION SELECT button while in this display toselect English, ...

AM Reception AM sound is based on wave amplitude, so AM receptioncan be disrupted by such things as lightning, power linesand neon signs. FM Reception Because FM transmission is based on frequency varia-tions, interference that consists of amplitude variationscan be filtered out, leaving the recepti...

Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary)Press the ON/VOL control to turn the radio ON. Pressthe ON/VOL a second time to turn OFF the radio. Electronic Volume ControlThe electronic volume...

Phone Button (UConnect™ Hands Free Phone) —If EquippedPress this button to operate the Hand Free Phone (UCon-nect™) feature (if equipped). Refer to “Hands-Free Com-munication (UConnect™)” in Section 3 for more informa-tion. If your vehicle is not equipped with or this feature is notavailable on your...

Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptableMP3/WMA file recording media and formats are limited.When writing MP3/WMA files, pay attention to thefollowing restrictions. Supported Media (Disc Types)The MP3/WMA file recording media supported by theradio are CDDA...

If a disc contains multi formats, such as CD audio andmp3/wma tracks, the radio will only play the mp3/wmatracks on that disc. Supported MP3/WMA File FormatsThe radio will recognize only files with the *.MP3/WMAextension as MP3/WMA files. Non-MP3/WMA filesnamed with the *.MP3/WMA extension may cause...

Operation Instructions - Auxiliary ModeThe auxiliary (AUX) jack is an audio input jack, whichallows the user to plug in a portable device such as anMP3/WMA player, cassette player, or microphone andutilize the vehicle’s audio system to amplify the sourceand play through the vehicle speakers. Pushing...

For UConnect™ “Voice Recognition System (VR) — IfEquipped ” refer to “Hands-Free Communication (UCon-nect™)” in section 3 of this manual for detailed operatinginstructions. Operating Instructions - Hands Free Phone(UConnect™) (If Equipped)Refer to “Hands-Free Communication (UConnect™)” inSection 3 o...

SALES CODE RES — AM/FM STEREO RADIOWITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (R...

If a preset button is activated while in the Music Type(Program Type) mode, the Music Type mode will beexited and the radio will tune to the preset station. SETUP ButtonPressing the SETUP button allows you to select betweenthe following items: • Set Clock — Pressing the SELECT button will allow user...

CAUTION! • This CD player will accept 4 3/4 inch (12 cm) discsonly. The use of other sized discs may damage theCD player mechanism. • Do not use adhesive labels. These labels can peelaway and jam the player mechanism. • RES is a single CD player. Do not attempt to inserta second CD if one is already...

TIME ButtonPress this button to change the display from a large CDplaying time display to a small CD playing time display. RW/FFPress the RW button to stop the CD at the beginning ofthe current CD track/title. Press and hold FF (Fast Forward) and the CD player willbegin to fast forward until FF is r...

Operating Instructions — Satellite Radio Refer to your “Navigation User’s Manual” for detailedoperating instructions. Clock Setting Procedure The GPS receiver used in this system is synchronized tothe time data being transmitted by the GPS satellite. Thesatellites’ clock is Greenwich Mean Time (GMT)...

Electronic Serial Number/Sirius IdentificationNumber (ENS/SID) The Electronic Serial Number/Sirius Identification Num-ber is needed to activate your Sirius Satellite Radiosystem. To access the ESN/SID, refer to the followingsteps: ESN/SID AccessWith the ignition switch in the ON/RUN or ACCESSORYposi...

• Dense tree coverage may interrupt reception in theform of short audio mutes. • Driving under wide bridges or along tall buildings cancause intermittent reception. • Placing objects over or too close to the antenna cancause signal blockage. Operating Instructions - Satellite Mode NOTE: The ignition...

REMOTE SOUND SYSTEM CONTROLS — IFEQUIPPED The remote sound system controls are located on the rearsurface of the steering wheel. Reach behind the wheel toaccess the switches. The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch willincrease t...

The button located in the center of the left hand controlwill tune to the next pre-set station that you haveprogrammed in the radio pre-set push-buttons. CD Player Pressing the top of the switch once will go to the nexttrack on the CD. Pressing the bottom of the switch oncewill go to the beginning o...

CLIMATE CONTROLS Manual Air Conditioning and Heating System The controls for the heating/air conditioning and venti-lation system in this vehicle consist of a series of rotaryknobs. These comfort controls can be set to obtain desiredinterior conditions. The instrument panel features four airflow reg...

Temperature Control Use this control to regulatethe temperature of the air in-side the passenger compart-ment. The blue area of thescale indicates cooler tem-peratures while the red areaindicates warmer tempera-tures. NOTE: If your air conditioning performance seems lower than expected, check the fr...

Circulation Control Press the mode control knobto activate the recirculationmode. A lamp (in the knob)will illuminate when you arein recirculate mode. Press theknob again to deactivate thesystem. Only use the recircu-lation mode to temporarilyblock out any outside odors,smoke, or dust and to cool th...

Operating Tips Window FoggingWindows will fog on the inside when the humidity insidethe vehicle is high. This often occurs in mild or cooltemperatures when it’s rainy or humid. In most cases,turning on the air conditioning (pressing the snowflakebutton) will clear the fog. Adjust the temperature con...

STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 245 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 245 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 245 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 245 ▫ Extreme C...

Tip Start Feature — Automatic Transmission OnlyDo not press the accelerator. Turn the ignition key briefly to START position, and release it. The starter motor willcontinue to run, but will automatically disengage itselfwhen the engine is running. Extreme Cold Weather (below –20°F or –29°C) To insur...

WARNING! Remember to disconnect the cord before driving.Damage to the 110-115 volt AC electrical cord couldcause electrocution. Use the heater when temperatures below 0°F (-18°C) areexpected to last for several days. MANUAL TRANSMISSION — IF EQUIPPED 6-Speed Manual Transmission WARNING! You or other...

• When “rocking” a stuck vehicle by shifting between aforward gear and reverse, do not spin wheels fasterthan 15 mph (24 km/h), or drivetrain damage mayresult. Recommended Manual Transmission ShiftingSpeedsThe manufacturer recommends that you use the shiftspeeds listed in the chart below. Manual Tra...

CAUTION! Failure to follow the recommended downshiftingspeeds may cause the engine to over speed and/ordamage the clutch disc even if the clutch pedal isdepressed. AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow-ing precautions are not observed: • Shift into P (Par...

WARNING! It is dangerous to shift the selector lever out of P(Park) or N (Neutral) if the engine speed is higherthan idle speed. If your foot is not firmly on thebrake pedal, the vehicle could accelerate quicklyforward or in reverse. You could lose control of thevehicle and hit someone or something....

4. Using the screwdriver, reach into the manual overrideopening. Press and hold the shift lock lever down. 5. Move the shift lever into the N (Neutral) position. 6. The vehicle may then be started in N (Neutral). Have your vehicle inspected by your local authorizeddealer, if the shift lock manual ov...

4–Speed Automatic Transmission (3.7L Engine) Shifting from D (Drive) to P (Park) or R (Reverse) (orfrom P or R to D) should be done only after theaccelerator pedal is released and the vehicle is stopped.Be sure to keep your foot on the brake when moving theshift lever between these gears. Gear Range...

WARNING! It is dangerous to shift the selector lever out of P(Park) or N (Neutral) if the engine speed is higherthan idle speed. If your foot is not firmly on thebrake pedal, the vehicle could accelerate quicklyforward or in reverse. You could lose control of thevehicle and hit someone or something....

5–Speed Automatic Transmission (4.0L Engine) The electronically controlled transmission provides aprecise shift schedule. The transmission electronics areself-calibrating; therefore, the first few shifts on a newvehicle, may be somewhat abrupt. This is a normalcondition, and precision shifts will de...

the transmission. This condition is normal and will notcause damage to the transmission. The torque converterwill refill within five seconds of shifting from Park intoany other gear position. FOUR-WHEEL DRIVE OPERATION MP 143 Single-Speed Part-Time Transfer Case —If Equipped Operating Information/Pr...

wheels to rotate at the same speed. This is accomplishedby rotating the 4WD Control Switch to the desiredposition - refer to “Shifting Procedure” for specific shift-ing instructions. The 4WD LOCK position is designed forloose, slippery road surfaces only. Driving in the 4WDLOCK position on dry hard ...

Driving In Snow, Mud and Sand In heavy snow, when pulling a load, or for additionalcontrol at slower speeds, shift the transmission to a lowgear and shift the transfer case to 4L or 4LO if necessary.Refer to “Four-Wheel Drive Operation” in this section.Do not shift to a lower gear than necessary to ...

• After extended operation in mud, sand, water, orsimilar dirty conditions, have brake rotors, wheels,brake linings, and axle yokes inspected and cleaned assoon as possible. WARNING! Abrasive material in any part of the brakes may causeexcessive wear or unpredictable braking. You mightnot have full ...

NOTE: The instrument cluster “Brake Warning Light” indicates only that the parking brake is applied. You mustbe sure the parking brake is fully applied before leavingthe vehicle. Be sure the parking brake is firmly set when parked, andthe gear selector lever is in the “P” (Park) position(automatic t...

WARNING! • Always apply the parking brake fully when leav-ing your vehicle or it may roll and cause damage orinjury. Also, be certain to leave an automatictransmission in “P” (Park) or a manual transmis-sion in “R” (Reverse) or 1st gear. Failure to do somay allow the vehicle to roll and cause damage...

WARNING! • The Anti-Lock Brake System (ABS) cannot preventthe natural laws of physics from acting on thevehicle, nor can it increase braking or steeringefficiency beyond that afforded by the conditionof the vehicle brakes and tires or the tractionafforded. • The ABS cannot prevent accidents, includi...

• Do not “ride” the brakes by resting your foot on thepedal. This could overheat the brakes and result inunpredictable braking action, longer stopping dis-tances, or brake damage. • When descending mountains or hills, repeated brak-ing can cause brake fade with loss of braking control.Avoid repeated...

NOTE: Increased noise levels at the end of the steering wheel travel are considered normal and do not indicatethat there is a problem with the power steering system. Upon initial start-up in cold weather, the power steeringpump may make noise for a short amount of time. This isdue to the cold, thick...

TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. designstandards. P-Metric tires have the letter “P” moldedinto the sidewall preceding the size designation. Ex-ample: P215/65R15 95H. • European Metric tire sizing is based on Europeandesign standards. Ti...

Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ( ....blank.... ( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = S...

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load correspondingto its load index under certain operating conditions.—The maximum speed correspon...

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire;however, the date code may only be on one side. Tires withwhite sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for theTIN on the outboard side of black si...

Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side“B” pillar. Tire and Loading Information Placard This placard tells you important information about the:1) number of people that ca...

2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce tread life resulting in a need forearlier tire replacement. Under inflation also increasestire rolling resistance and results in higher fuel consump-tion. 3...

WARNING! Fast spinning tires can be dangerous. Forces gener-ated by excessive wheel speeds may cause tire dam-age or failure. A tire could explode and injure some-one. Do not spin your vehicle’s wheels faster than 35mph (55 km/h) when you are stuck, and do not letanyone near a spinning wheel no matt...

Life of Tire The service life of a tire is dependent upon varyingfactors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years,regardless of the remaining tread. Failure to followthis warning can result in sud...

WARNING! • Do not use a tire, wheel size or rating other than thatspecified for your vehicle. Some combinations ofunapproved tires and wheels may change suspensiondimensions and performance characteristics, result-ing in changes to steering, handling, and braking ofyour vehicle. This can cause unpre...

Improper alignment will not cause vehicle vibration.Vibration may be a result of tire and wheel out-of-balance. Proper balancing will reduce vibration andavoid tire cupping and spotty wear. TIRE CHAINS Use “Class S” chains or other traction aids that meet SAEType “S” specifications. NOTE: Chains mus...

These cautions apply to all chain traction devices, includ-ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires. NOTE: The use of class “S” chains is permitted with P235/65R17 tires. CAUTION! Do not use tire chains on vehicles equipped withtires other than P235/65R1...

NOTE: The Premium Tire Pressure Monitor System will automatically locate the pressure values displayed in thecorrect vehicle position following a tire rotation. The suggested rotation method is the “forward-cross”shown in the following diagram. TIRE PRESSURE MONITOR SYSTEM (TPMS) — IFEQUIPPED • The ...

pressure will also increase as the vehicle is driven - thisis normal and there should be no adjustment for thisincreased pressure. • The TPM System will warn the driver of a low tirepressure if the tire pressure falls below the low-pressure warning limit for any reason, including lowtemperature effe...

• Seasonal temperature changes will affect tire pressure,and the TPMS will monitor the actual tire pressure inthe tire. Base System — If Equipped The Tire Pressure Monitor System (TPMS) uses wirelesstechnology with wheel rim mounted electronic sensors tomonitor tire pressure levels. Sensors, mounted...

NOTE: Vehicles with Compact Spare1. The compact spare tire does not have a tire pressuremonitoring sensor. Therefore, the TPMS will not monitorthe pressure in the compact spare tire.2. If you install the compact spare tire in place of a roadtire that has a pressure below the low-pressure warninglimi...

• 3 Trigger Modules (mounted in three of the fourwheel-wells) • Various Tire Pressure Monitoring System Messages,which display in the Electronic Vehicle InformationCenter (EVIC) • Tire Pressure Monitoring Telltale Light The matching full size spare wheel and tire assembly (ifequipped) has a tire pre...

The tire pressure sensors are covered under one of thefollowing licenses: United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 Canada . . . . . . . . . . . . . . . . . . . . . . . . 2671-S120123 FUEL REQUIREMENTS 3.7L Engine (If Equipped) The 3.7L engine is designed to meet allemission...

• The use of leaded gas is prohibited by Federal law.Using leaded gasoline can impair engine performance,damage the emission control system. • An out-of-tune engine, or certain fuel or ignitionmalfunctions, can cause the catalytic converter tooverheat. If you notice a pungent burning odor orsome lig...

• Guard against carbon monoxide with proper mainte-nance. Have the exhaust system inspected every timethe vehicle is raised. Have any abnormal conditionsrepaired promptly. Until repaired, drive with all sidewindows fully open. • Keep the liftgate closed when driving your vehicle toprevent carbon mon...

CAUTION! Damage to the fuel system or emission control sys-tem could result from using an improper fuel cap(gas cap). A poorly fitting cap could let impuritiesinto the fuel system. Also, a poorly fitting after-market cap can cause the MIL (Malfunction IndicatorLight) to illuminate, due to fuel vapor...

NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properlytightened. If the gas cap is not tighten properly, the MalfunctionIndicator Light will come on. Be sure the gas cap istightened every time the vehicle is refueled. WARNING! A fire may result ...

Gross Trailer Weight (GTW)The gross trailer weight (GTW) is the weight of the trailerplus the weight of all cargo, consumables and equipment(permanent or temporary) loaded in or on the trailer in its 9 loaded and ready for operation 9 condition. The recom- mended way to measure GTW is to put your fu...

WARNING! An improperly adjusted Weight Distributing Hitchsystem may reduce handling, stability, braking per-formance, and could result in an accident. Weight Distributing Systems may not be compatiblewith Surge Brake Couplers. Consult with your hitchand trailer manufacturer or a reputable Recreation...

Trailer Hitch Classification Your vehicle is capable of towing trailers up to 2,000 lbs(907 kg) without added equipment or alterations to thestandard equipment. Your vehicle may be factoryequipped for safe towing of trailers weighing over 2,000lbs (907 kg) with the optional Trailer Tow Prep Package....

When Towing Trailers with Gross Trailer Weight (GTW) between 3,500 Lbs (1 588 kg) and 5,000 Lbs (2 268 kg)The following chart provides maximum trailer weight ratings towable for the following engine/transmissioncombinations, ONLY if using a weight distributing hitch. Engine/ Transmission Model GCWR ...

NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, andshould never exceed the weight referenced on the Tireand Loading Information placard. Refer to the Tire–Safety Information section in this manual. Trailer and Tongue Weight Always load a trai...

NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be con-sidered as part of the total load on your vehicle. Refer to theTire and Loading Information placard in the Tire SafetyInfor...

• When hauling cargo or towing a trailer, do not over-load your vehicle or trailer. Overloading can cause aloss of control, poor performance or damage to brakes,axle, engine, transmission, steering, suspension, chas-sis structure or tires. • Safety chains must always be used between yourvehicle and ...

− Also, check the trailer tires for proper tire inflation pressures before trailer usage. − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to the Tires–GeneralInformation section of this manual on Tread WearIndicators for the proper inspection procedure. − When re...

WARNING! Do not connect trailer brakes to your vehicle’s hy-draulic brake lines. It can overload your brake sys-tem and cause it to fail. You might not have brakeswhen you need them and could have an accident. Towing any trailer will increase your stopping dis-tance. When towing you should allow for...

Towing Tips Before setting out on a trip, practice turning, stoppingand backing the trailer in an area away from heavytraffic. If using a manual transmission vehicle for trailer towing,all starts must be in FIRST gear to avoid excessive clutchslippage. Towing Tips — Automatic TransmissionThe “D” ran...

− Use speed control in flat terrain and with light loads to maximize fuel efficiency. Towing Tips — Cooling SystemTo reduce potential for engine and transmission over-heating, take the following actions: − City DrivingWhen stopped for short periods of time, put transmissionin neutral and increase en...

Towing — 4WD or All-Wheel Drive Models CAUTION! Front or rear wheel lifts should not be used. Internaldamage to the transmission or transfer case will occurif a front or rear wheel lift is used when recreationaltowing. Recreational towing (all four wheels on theground)Recreational towing is NOT allo...

WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flashers . . . . . . . . . . . . . . . . . 334 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 335 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 336 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . . 336 ▫ Sp...

HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergencywarning system. When you activate it, all front and reardirectional signals will flash intermittently. Use it whenyour vehicle is disabled on or near the road. It warnsother drivers to steer clear of you and your vehicle. T...

IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce thepotential for overheating by taking the appropriate ac-tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in N(Neutral), but do not increase engine idle speed. NOTE: There are steps t...

JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous.The vehicle could slip off the jack and fall on you.You could be crushed. Never get any part of yourbody under a vehicle that is on a jack. If you needto get under a raised vehicle, take it to a servicecenter where i...

Spare Tire Stowage The spare tire is stowed underneath the rear of thevehicle and is held in place by a cable winch mechanism. Spare Tire Removal Fit the jack handle extension over the drive nut. Use theLug Wrench to rotate the nut counter clockwise until thespare is on the ground with enough slack ...

CAUTION! The winch mechanism is designed for use with thejack extension tube only. Use of an air wrench orother power tools is not recommended and they candamage the winch. When the spare is clear, tilt the retainer at the end of thecable, and pull it through the center of the wheel. Preparations Fo...

Jacking Instructions 1. Remove spare tire. 2. Loosen (but do not remove) the wheel lug nuts byturning them to the left one turn while the wheel is stillon the ground. 3. Remove jack and tools from mounting bracket. As-semble the tools by connecting the driver to the exten-sion, and then to the lug w...

5. Raise the vehicle by turning the jack screw to the right.Raise the vehicle only until the tire just clears the surfaceand enough clearance is obtained to install the spare tire.Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can makethe vehicle les...

9. Finish tightening the lug nuts. Push down on thewrench while tightening for increased leverage. Alternatenuts until each nut has been tightened twice. Correctwheel nut tightness is 130 N·m (95 ft. lbs). If in doubtabout the correct tightness, have them checked with atorque wrench by your authoriz...

NOTE: Transmission must be in “N” (Neutral) under any towing configuration. Two-Wheel Drive Vehicles Front Wheels RaisedThe speed must not exceed 30 mph (50 km/h) and thedistance must not exceed 15 miles (25 km). This vehicle may be towed with the transmission in “N”,the ignition key in the LOCK pos...

MAINTAINING YOUR VEHICLE CONTENTS m Engine Compartment – 3.7L . . . . . . . . . . . . . . . 348 m Engine Compartment – 4.0L . . . . . . . . . . . . . . . 349 m Onboard Diagnostic System — OBD II . . . . . . . . 350 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 351 m Emissions Inspection An...

ENGINE COMPARTMENT – 3.7L 348 MAINTAINING YOUR VEHICLE

ENGINE COMPARTMENT – 4.0L MAINTAINING YOUR VEHICLE 349 7

ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe performance of the emissions, engine, and automatictransmission control systems. When these systems areoperating properly, your vehicle will provide excell...

Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system candetermine if the fuel filler cap is possibly loose, improp-erly installed, or damaged. A loose fuel filler cap messagewill be displayed in the instrument cluster. Tighten thegas cap until a 9 clicking 9 sound is hear...

Your vehicle has a simple ignition key actuated test,which you can use prior to going to the test station. Tocheck if your vehicle’s OBD system is ready, you must dothe following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crankor start ...

Regardless of whether your vehicle’s OBD system isready or not ready, if the MIL symbol is illuminatedduring normal vehicle operation, you should have yourvehicle serviced before going to the I/M station. The I/Mstation can fail your vehicle because the MIL symbol is onwith the engine running. REPLA...

Engine Oil Filter SelectionAll of the manufacturer’s engines have a full-flow typedisposable oil filter. Use a filter of this type for replace-ment. The quality of replacement filters varies consider-ably. Only high quality filters should be used to assuremost efficient service. Mopar t engine oil f...

Catalytic Converter The catalytic converter requires the use of unleaded fuelonly. Leaded gasoline will destroy the effectiveness of theconverter as an emission control device. Under normal operating conditions, the catalytic con-verter will not require maintenance. However, it is im-portant to keep...

WARNING! • Use only refrigerants and compressor lubricantsapproved by the manufacturer for your air condi-tioning system. Some unapproved refrigerants areflammable and can explode, injuring you. Otherunapproved refrigerants or lubricants can causethe system to fail, requiring costly repairs. Refer t...

WARNING! Fluid level should be checked on a level surface withthe engine off to prevent injury from moving parts,and to insure accurate fluid level reading. Do notoverfill. Use only the manufacturer’s recommendedfluid. If necessary, add fluid to restore to the proper indicatedlevel. With a clean clo...

amount of a high quality lubricant such as Mopar t Lock Cylinder Lubricant directly into the lock cylinder. Windshield Wiper Blades Clean the rubber edges of the wiper blades and thewindshield periodically with a sponge or soft cloth and amild non-abrasive cleaner. This will remove accumula-tions of...

Use only high purity water such as distilled or deionizedwater when mixing the water/antifreeze (coolant) solu-tion. The use of lower quality water will reduce theamount of corrosion protection in the engine coolingsystem. Please note that it is the owner’s responsibility to main-tain the proper lev...

children, do not store ethylene glycol based antifreeze/coolant in open containers or allow it to remain inpuddles on the ground. If ingested by a child, contact aphysician immediately. Clean up any ground spills im-mediately. Engine Coolant LevelThe coolant bottle provides a quick visual method for...

• Check antifreeze/coolant freeze point in the radiatorand in the coolant recovery bottle. If antifreeze/coolant needs to be added, contents of coolant recov-ery bottle must also be protected against freezing. • If frequent antifreeze/coolant additions are required,or if the level in the recovery bo...

are present. Components should be replaced immedi-ately if there is any evidence of degradation that couldcause failure. Brake System In order to assure brake system performance, all brakesystem components should be inspected periodically.Refer to the appropriate “Maintenance Schedule” inSection 8 f...

Use only brake fluid that has been in a tightly closedcontainer to avoid contamination from foreign matter. Donot allow petroleum base fluid to contaminate the brakefluid as seal damage will result. Automatic Transmission Selection of LubricantIt is important that the proper lubricant is used in the...

Transfer Case Fluid Level CheckThe fluid level should be to the bottom edge of the fillhole (A) when the vehicle is in a level position. Adding FluidFluid should be added only at filler hole until fluidbegins to run out of the hole. DrainFirst remove fill plug (B), then drain plug (C). Recom-mended ...

Front/Rear Axle Fluid Fluid Level CheckLubricant should be at bottom edge of the oil fill hole. Adding FluidAdd lubricant only at the fill hole and only to the levelspecified above. Selection of LubricantUse only manufacturer’s recommended fluid, refer to Fluids,Lubricants, and Genuine Parts for cor...

Washing • Wash your vehicle regularly. Always wash your ve-hicle in the shade using Mopar t Car Wash or a mild car wash soap, and rinse the panels completely withclear water. • If insects, tar, or other similar deposits have accumu-lated on your vehicle, use Mopar t Super Kleen Bug and Tar Remover t...

Cleaning Plastic Instrument Cluster LensesThe lenses in front of the instruments in this vehicle aremolded in clear plastic. When cleaning the lenses, caremust be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may beused, but do not use high alcohol content...

Cavity Cartridge Fuse Mini Fuse Description M29 10 AmpRed Occupant Classifica-tion Module (OCM) M30 15 AmpBlue Rear Wiper Module(RR WIPER MOD),Power Folding Mirror(PWR FOLD MIR) M31 20 AmpYellow Back-Up Lamps (B/ULAMPS) M32 10 AmpRed Occupant RestraintController (ORC), TTEUROPE M33 10 AmpRed Next Ge...

5. Disconnect the electrical connector and replace thebulb. Left Front Turn Signal 1. Turn the steering wheel all the way to the right (fullright lock). 2. Remove the door in the left wheel liner by twistingcounter clockwise. Access to the bulb can be gainedthrough the wheel liner hole. 3. Disconnec...

Right Front Turn Signal 1. Open the hood. 2. Reach behind the headlamp unit in the engine com-partment to access the turn signal bulb. 3. Twist the bulb counter clockwise to remove. 4. Disconnect the electrical connector and replace thebulb. Front Side Marker 1. Open the hood. 2. Remove the grille a...

4. Remove the two screws attaching the backplate to thelamp assembly. 5. Pull the backplate straight back from the lamp hous-ing. 6. Disconnect the electrical connector. 7. Remove the bulb from the backplate. Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. Disc...

FLUID CAPACITIES U.S. Metric Fuel (Approximate) 19.5 Gallons 73.8 Liters Engine Oil with Filter3.7 Liter Engine (SAE 5W-20, API Certified Engine Oil) 5 Qts 4.7 Liters 4.0 Liter Engine (SAE 10W-30, API Certified Engine Oil) 6 Qts 5.7 Liters Cooling System *3.7 Liter Engine (Mopar t Antifreeze/Engine ...

Chassis Component Fluids, Lubricants and Genuine Parts. Automatic Transmission Mopar t ATF+4, Automatic Transmission Fluid. Manual Transmission Mopar t Manual Transmission Lubricant or equivalent (meeting the re- quirements of DaimlerChrysler Material Standard MS-9224) Transfer Case Mopar t ATF+4, A...

MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . . . 398 m Maintenance Schedule . . . . . . . . . . . . . . . . . . . 398 ▫ Required Maintenance Intervals . . . . . . . . . . . 401 8 M A I N TE N A N C E SC H E DU LE S

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in boldtype must be done at the times or mileages specified to assure the continued proper functioning of the emissioncontrol system. These, and all other maintenance servicesincluded in this manual, should be done to p...

NOTE: • The oil change indicator message will not monitor thetime since the last oil change. Change your vehicles oilif it has been 6 months since your last oil change evenif the oil change indicator message is NOT illumi-nated. • Change your engine oil more often if you drive yourvehicle off-road f...

Required Maintenance Intervals Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the engine oil and engine oil filter. 6,000 10 000 6 Rotate tires. 6,000 10 000 6 If using your vehicle for any of ...

Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Flush and replace the engine coolant. 102,000 170 000 60 Replace the spark plugs (4.0L Only). 102,000 170 000 102 Replace the timing belt (4.0L Only). 10...

IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For YourVehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 ▫ Prepare For The Appointment . . . . . . . . . . . . 406 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 406 ▫ Be Reasonable ...

WARNING! Engine exhaust, some of its constituents, and certainvehicle components contain or emit chemicalsknown to the State of California to cause cancer andbirth defects or other reproductive harm. In addition,certain fluids contained in vehicles and certain prod-ucts of component wear contain or ...

To contact NHTSA, you may either call the Auto SafetyHotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153),or go to http://www.safercar.gov; or write to: Administra-tor, NHTSA, 400 Seventh Street, SW., Washington, DC20590. You can also obtain other information about motorvehicle safety from htt...

Temperature Grades The temperature grades are A (the highest), B, and C,representing the tire’s resistance to the generation of heatand its ability to dissipate heat when tested undercontrolled conditions on a specified indoor laboratorytest wheel. Sustained high temperature can cause thematerial of...

Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262Auxiliary Electrical Outlet (Power Outlet) . . . . . . 147 Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . 147 Axle Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 Battery . . . . . . . . . . . . ...

Octane Rating . . . . . . . . . . . . . . . . . . . . . . 306,395Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 394Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . 394 Fuel System Caution . . . . . . . . . . . . . . . . 308,311,312Fuses . . . . . . . . . . . . . . . . . ...

Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 319 Holder, Coin . . . . . . . . . . . . . . . . . . . . . . . . . . . 152Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . 151HomeLink t (Garage Door Opener) Transmitter . . . 137 Hood Release . . . . . . . . . ....

Shoulder Belt Anchorage . . . . . . . . . . . . . . . . . . 44 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 113Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379Head Restraints . . . . . ....

Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . . 246Emergency (Jump Starting) . . . . . . . . . . . . . . . 341Engine Block Heater . . . . . . . . . . . . . . . . . . . . 248Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 246Manual Transmission . . . . . . . . . . . . . ....

Warranty Information . . . . . . . . . . . . . . . . . . . . . 409Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . . . 159Washers, Windshield . . . . . . . . . . . . . . . . . . . . . 365Waxing and Polishing . . . . . . . . . . . . . . . . . . . . . 378Wheel Alignment and Balance . . . . ....