Dixon 966 004901 - Manuals

Husqvarna - 5 SAFETY RULES DANGER ! THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS GENERAL OPERATION • Read, understand and fo...

6 - Husqvarna SAFETY RULES DO NOT • Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. • Do not mow near drop-off, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. • Do...

8 - Husqvarna ASSEMBLY BAGGER ASSEMBLY Attach hitch tube to support bracket with 1. 3 / 8 -16 x 2 shoulder bolts and secure with flange nuts. HITCH TUBE SUPPORT BRACKET Place the support bracket against the frame rear 2. guard. Using the outer right hole and inner left hole, secure with 5 / 16 x 1 b...

10 - Husqvarna Deck Height Adjustment ASSEMBLY DRIVE PULLEY Remove the discharge chute from the deck. (Deck 1. configuration will vary by size and model)Lower deck to the lowest cutting position. 2. Remove the right hand (discharge side) belt cover 3. from the deck.Relieve the tension from the deck ...

Husqvarna - 11 ASSEMBLY BLOWER ASSEMBLY Position blower over the discharge tabs on the 1. deck and set blower onto the deck.Be sure the blower is sitting flush against the 2. outside of the deck.Secure the mount bracket to the deck with the pin 3. and hairpin cotter supplied with the kit. Mount Brac...

12 - Husqvarna ASSEMBLY MIDDLE CHUTE BLOWER ASSEMBLY MIDDLE CHUTE 1. Place middle chute over the top end of the blower assembly. 2. Latch middle chute to blower assembly. BELT COVERS Place the deck belt shield on the deck over the 1. drive pulley and secure with hardware removed from steel belt shie...

Husqvarna - 13 ASSEMBLY 2¾ BOLT 3¾ BOLT WEIGHT BRACKET CAST WEIGHT WEIGHT KIT 1. Bolt cast weight and two weight brackets together using 2¾" bolts and nuts. 2. Slide both weight brackets over the front tube on the frame, positioning the assembly in the center of the frame. 3. Secure with 3¾"...

14 - Husqvarna TRANSPORT STORAGE When grass catcher is to be stored for a period of time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a clean, dry place. Also clean machine and cover all scratches with touch-up paint. Covered or indoor storage is recommended. HOSE CARE Inspect...

Husqvarna - 15 SERVICE AND MAINTENANCE PREVENTATIVE MAINTENANCE SCHEDULE TROUBLESHOOTING GUIDE Before Each Use Every 5 Hours Every 25 Hours Every 55 Hours Inspect/Clean Poly Mesh X X Check/Tighten Nuts & Bolts X Check/Tighten Hoses X Turn Hose End to End X Rotate Hose X Clean Machine X Inspect B...

16 - Husqvarna TIPS FOR IMPROVED BAGGING Follow the mower operation instructions in the mower operator’s manual.When utilizing the grass catcher on a lawn where grass and leaf bagging equipment has not been used, thatch and debris that has accumulated for long periods of time will be picked up. The ...

Husqvarna - 17 CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS Always observe safety rules when performing any maintenance.• Before each use check for loose fasteners.• Clean unit thoroughly after each use. BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades...

18 - Husqvarna HOOD 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 18 19 22 10 20 19 21 14 23 24

20 - Husqvarna HITCH 2 3 4 5 6 7 8 9 10 12 13 14 15 18 11 7 1 10 16 10 7 7 10 10 7 17 19 21 20 22 23 27 26 25 24 10 28

22 - Husqvarna BLOWER 2 4 5 7 8 9 40 14 32 13 47 10 17 17 59 11 20 21 18 43 24 25 62 41 20 60 30 31 49 39 36 44 26 66 45 65 38 37 42 6 33 28 36 29 50 48 57 31 22 46 52 48 1 3 61 16 27 63 61 64 30 22 24 46 47 45 48 35 33 51 36 54 55 33 34 19 19 58 23 53 15 56 59 12 67 69 68

24 - Husqvarna WEIGHT 2 7 6 5 4 3 1 8 9 10 11 COLLECTION BAG 11 14 12 13 3

Husqvarna - 25 WEIGHT 522 989002 1.. .... 1 .... BRACKET, WEIGHT 539 111587 2.. .... 1 .... WEIGHT, CAST 521 996501 3.. .... 8 .... NUT 3 / 8 -16 HEX FLANGE 539 101341 4.. .... 4 .... HCS 3 / 8 -16 x 3 539 990122 5.. .... 8 .... WASHER 3 / 8 SAE FLAT 539 990118 6.. .... 4 .... WASHER 3 / 8 SLW 539 1...