Dixon 6025 - Manuals

Page 5 SAFETY Safety Alert Symbol When you see this symbol, BE ALERT to the potential for injury. Follow recommended safety precautions and safe operating practices. Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning indicates a ...

Page 8 CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing activity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents. • Keep children out of the mowing area and unde...

Page 11 SPECIFICATIONS Model ZTR 3303 CHASSIS: Twin 12 gauge side frames and 7 gauge transmission and engine base plate. BODY: All body parts are made of rotational molded polyethylene. Front body contains access panel for battery service. Seat tilts forward to allow transmission service. MOWER DECK...

Page 14 1. Raise and push seat assembly forward. 2. Loosen five nuts, P/N 3205, and slide seat forward or backward to desiredposition. 3. Re-tighten nuts, P/N 3205. DO NOT operate mower without seat adjustmentsproperly tightened. 4. Push seat assembly back to closed position. SEAT ADJUSTMENT INSTRUC...

Page 15 CONTROLS The Dixon ZTR has a unique transaxle that requires only two drive levers to control braking, turning, speed, and direction. On initial operation, set throttle speed on slow. Operate with mower blade "OFF". To avoid "over-controlling" the mower, use a light touch on t...

Page 17 BLADE DRIVE: Models ZTR 3303 & 3304 Located to left of operator. To engage the mower blade, turn lever on floor slowly to the "ON" position. To disengage mower blade, turn lever to the "OFF" position. BLADE DRIVE: Model ZTR 3014 Located on control panel, on operator's rig...

Page 18 OPERATION INSTRUCTIONS Safe and successful operation will depend upon the operator having the correct knowledge of all controlsused on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and th...

Page 19 PARKING BRAKE SWITCH TEST: a)Place Parking Brake in OFF positionb)Turn ignition switch to START Engine should not turn over or attempt to start. BLADE DRIVE SWITCH TEST: a)Place Parking Brake in ON positionb)Engage blade drive switchc)Turn ignition switch to START Engine should not turn over...

Page 20 OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: 1. Parking brake must be on, and blade drive disengaged. 2. Move throttle control to "Choke" position if engine is cold, full throttle if warm. 3. Insert ignition key and turn to "Start" position. When engine starts, release ignit...

Page 21 OPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT: Mulching or recycling the grass clippings requires a totally different mowing approach than would be normalwhen side discharging or bagging the grass. There may be instances or conditions where it is not possibleto hide all of the rec...

Page 22 OPERATION INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT: In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below. 1. Set engine speed control to the wide open or full setting. 2. Do Not Attempt To Cut Grass When...

Page 23 OPERATION INSTRUCTIONS SIDE DISCHARGE OF THE CLIPPINGS: In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the troubleshooting guide. Be sure that deflector is properly instal...

Page 24 CARE AND MAINTENANCE This portion of the owners manual deals with normal service items which can be performed by the owner.Please remember that if you are in doubt as to the correct service procedures to be followed, these and otherservice situations can be handled by a Dixon ZTR dealer who ...

Page 25 CARE AND MAINTENANCE CUTTER BLADE MAINTENANCE: NOTE: Observe proper blade position prior to removal. 1. Safely raise front of mower. 2. Hold or block blade from turning. 3. Loosen blade nut and remove blade. 4. When replacing blade, tighten blade nut secur ely. Refer to diagram. Wear heavy, ...

Page 27 CARE AND MAINTENANCE DECK REMOVAL - ELECTRIC CLUTCH MODEL ZTR 3014 1. Place cut height lever in lowest cut position. 2. For 36" decks, loosen nut on belt idler shock mount until belt can be removed from electric clutch pulley on the bottom of the engine. Refer to illustration below. For ...

Page 29 CARE AND MAINTENANCE HOT oil may cause burns.Allow engine to cool before draining oil. CHANGING THE ENGINE OIL: 1. The "Dapco" oil drain valve is located on the left side of the engine crankcase. 2. Place a suitable container under the drain valve. The fitting of a short piece of hos...

Page 30 CARE AND MAINTENANCE DRIVE SYSTEM ADJUSTMENTS: Due to both the complex nature of the transmission and the number of specialtools required for service, adjustments should be entrusted to your dealer. There are a number of simple owner service items which greatly influence theperformance of th...

Page 32 STANDARD SERVICE PARTS LIST MODELS ZTR 3303 & ZTR 3304 BLADES: Standard: P/N 2483 Hi-Lift: P/N 2484 BELTS: Engine To Mower Deck: P/N 7725 Engine To Transmission: P/N 7650 MODEL ZTR 3014 36" Deck 42" Deck BLADES: Standard P/N 1324 Lo-lift P/N 8688 Hi-lift P/N 1351 Hi-lift(R) P/N 6...

Page 33 SITUATION CAUSES REMEDY Poor cut quality Ground speed Reduce mowing speed Poor cut quality Loose engine to Refer to Page 26 mower deck belt Poor cut quality Engine RPM too low Increase engine RPM to maximum Poor cut quality Dull or bent blade Sharpen or replace as required Poor cut quality U...