Dixon 1857-0599 - Manuals

Page 5 SAFETY SAFETY SYM BOLS Safety Alert Symbol When you see this symbol, BE ALERT to the potential for injury. Follow recommended safety precautions and safe operating practices. Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warn...

Page 6 WARNING : The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. This cutting mower is capable of amputating hands & feet, and throwing objects. Failure to observe the following safety instruction...

Page 7 SAFETY SLOPE OPERATION: Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. DO Mow across the slope with your Dixo...

Page 10 DIXON LIMITED WARRANTY POLICY -- ZTR Model 4500 This warranty policy applies to all Model 4500 mowers purchased on or after September 1, 1997. WARRANTY:Commercial Applications: Dixon ZTR Models 4500 used in any commercial application are warranted for a period ofninety (90) days from date of...

Page 11 SPECIFICATIONS Models ZTR 4515B and 4516K CHASSIS: Twin 12 gauge side frames and 7 gauge transmission and engine base plate. BODY: All body parts are made of high density polyethylene. Dent and corrosion resistant.Front body contains access panel for battery service. MOWER DECKS: 42" Dec...

Page 12 SEAT ADJUSTMENT INSTRUCTIONS 1 . Place parking brake in ON position. (Pull brake lever up) 2. Raise and push seat assembly forward. 3. Loosen five nuts, P/N 3205, and slide seat forward or backward to desired position.Retighten nuts, P/N 3205. DO NOT operate mower without seat adjustments pr...

Page 14 CONTROLS PARKING BRAKE: The parking brake is designed to hold the mower frommoving and is not intended for use in stopping the mowerwhile it is in motion. The engine will stop if the parkingbrake is engaged while the control levers are in the driveposition. TO SET PARKING BRAKE: The hand ope...

Page 16 BLADE DRIVE: Located on control panel, on operator's right. To engage the mower blades, pull up on theswitch. To disengage blades, push down. CIRCUIT BREAKER: Protection of the electrical system is by(1) 15 amp circuit breaker. If circuit breaker trips, push button to reset. If this conditio...

Page 17 OPERATION INSTRUCTIONS Safe and successful operation will depend upon the operator having the correct knowledge of all controls usedon the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and th...

Page 18 OPERATION INSTRUCTIONS PARKING BRAKE SWITCH TEST: a) Swing out control leversb) Disengage blade drive switchc) Put Parking brake in OFF positiond) Turn ignition switch to START Engine should not turn over or attempt to start. CONTROL LEVER SWITCH TEST: a) Disengage blade drive switch b) Put ...

Page 19 OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: 1. Parking brake must be on, control levers swung out, and blade drive disengaged. 2. Move throttle control to "Choke" position if engine is cold, full throttle if warm. 3. Insert ignition key and turn to "Start" position. When en...

Page 20 OPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT: Mulching or recycling the grass clippings requires a totally different mowing approach than would be normalwhen side discharging or bagging the grass. There may be instances or conditions where it is not possibleto hide all of the rec...

Page 21 OPERATION INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT: In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below. 1. Some applications may require installation of an "Optional" weight box on the front of...

Page 22 OPERATION INSTRUCTIONS SIDE DISCHARGE OF THE CLIPPINGS: I n order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the troubleshooting guide. 1. Set engine speed control to the wide ...

Page 23 CARE AND MAINTENANCE This portion of the owners manual deals with normal service items which can be performed by the owner. Pleaseremember that if you are in doubt as to the correct service procedures to be followed, these and other service situationscan be handled by a Dixon ZTR dealer who ...

Page 24 CARE AND MAINTENANCE MOWER BLADE MAINTENANCE: NOTE: Observe proper blade position prior to removal. 1. Safely raise front of mower. 2. Hold or block blade from turning. 3. Loosen blade nut and remove bla de. 4. When replacing blade, tighten blade nut securely. Refer to diagram. CAUTION Wear ...

Page 26 CARE AND MAINTENANCE FORWARD TRAVEL SPEED ADJUSTMENT 1. Drive machine until hydrostats have warmed up. 2. Drive on a smooth, level surface with both levers in top speed position. 3. If one side now drives slightly faster than the other, adjust lever stop washer P/N 5760 on that side to reduc...

Page 27 CARE AND MAINTENANCE NEUTRAL ADJUSTMENT DRIVE MACHINE UNTIL HYDROSTATS HAVE WARMED UP. WITH ENGINE RUNNING ANDTHE PARKING BRAKE OFF, SWING OUT THE CONTROL LEVERS. IF MACHINE STARTS TOCREEP, FOLLOW THE INSTRUCTIONS BELOW. 1 . Stop the engine, engage parking brake, and raise rear of frame with...

Page 28 CARE AND MAINTENANCE MOWER DECK LEVELING PROCEDURE: 1. Place mower on a smooth, level surface and check tire pressures to insure correct stance. Tires should be inflated as follows: Front: 16 - 21 lbsRear: 8 - 14 lbs 2. Turn each outer blade tip to align with the deck in a side to side manne...

Page 30 CARE AND MAINTENANCE CHANGING THE ENGINE OIL: 1. The "snap lock" oil drain valve is located on the left side of the engine crankcase. 2. Place a suitable container under the drain valve. The fitting of a short piece of hose to the valve will help direct the oil. 3. Push the valve bod...

Page 32 CARE AND MAINTENANCE WHEELS AND TIRES: Correct tire pressure is important for correct operationof mower. Front Tires 11 X 4.00 X 5 16-21 PSI Rear Tires 18 X 8.50 X 8 8-14 PSI NOTE: Check lug nuts periodically for tightness. ELECTRICAL SYSTEMS: Keep all connections clean and tight. CLEANING T...

Page 33 STANDARD SERVICE PARTS LIST 42" DECK: BLADES: Standard Hi-Lift: P/N 8688 Lo-Lift: P/N 6236 BELTS: Engine To Mower Deck: P/N 5861 Serpentine Belt: P/N 6109 Engine To Transmission: P/N 5768 50" DECK" BLADES: Standard Hi-Lift: P/N 9444 Lo-Lift: P/N 9443 BELTS: Engine To Mower Deck: ...

Page 34 Poor cut quality Poor cut quality Poor cut quality Poor cut quality Poor cut quality Poor cut quality Poor cut quality Poor cut quality TROUBLESHOOTING MOWER CUT QUALITY: There are many variables that can effect the cut quality of any riding mower. Type and conditions of grass,cut height set...