Dewalt DXPW3835- Manuals

Dewalt DXPW3835– User Manual in PDF format online.

Manuals:

User Manual

User Manual Dewalt DXPW3835

Summary

Page 3 - The definitions below describe the level of severity for each; Specifications

3 E n g lis h Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury . WARNI...

Page 4 - What can haPPen

4 E n g li sh WARNING: Do not operate this unit until you read this instruction manual and the engine instruction manual for safety, operation and maintenance instructions. WARNING: When using this product basic precautions should always be followed, including the following:1. Read all instructions ...

Page 5 - lis

5 E n g lis h • Operating the pressure washer in an ex plo sive en viron ment could re sult in a fire. • Operate and fuel equipment in well-ven ti lat ed areas free from ob struc tions. Equip areas with fire extinguisher suit able for gas o line fires. • Materials placed against or near the pressure...

Page 6 - DANGER: RISk Of fLUID INjECTION AND LACERATION

6 E n g li sh • Do not allow hose to contact muf fler. • Never attach or remove wand or hose fittings while sys tem is pres sur ized. • When using replacement lances or guns with this pressure washer, DO NOT use a lance and/or lance/ gun combination that is shorter in length than what was provided w...

Page 7 - DANGER: RISk Of INjURY fROM SpRAY; DANGER: RISk Of UNSAfE OpERATION

7 E n g lis h DANGER: RISk Of INjURY fROM SpRAY What can haPPen hoW to PreVent It • High-velocity fluid spray can cause objects to break, propelling particles at high speed. • Always wear ANSI-approved Z87.1 safety glasses. Wear protective clothing to protect against accidental spraying. • Never poi...

Page 8 - DANGER: RISk Of INjURY OR pROp ER TY DAMAGE

8 E n g li sh • If proper starting procedure is not followed, engine can kickback causing serious hand and arm injury. • If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickb...

Page 9 - WARNING: RISk Of BURSTING; WARNING: RISk Of hOT SURfACES

9 E n g lis h WARNING: RISk Of BURSTING What can haPPen hoW to PreVent It • Over inflation of tires could result in serious injury and property damage. • Use a tire pressure gauge to check the tires pressure before each use and while inflating tires; see the tire sidewall for the correct tire pressu...

Page 10 - WARNING: RISk Of ChEMICAL BURN; SAvE thESE INStructIoNS; Risk of personal injury. Avoid placing

10 E n g li sh WARNING: RISk Of ChEMICAL BURN What can haPPen hoW to PreVent It • Use of acids, toxic or corrosive chemicals, poisons, in sec ti cides, or any kind of flam ma ble solvent with this product could re sult in se ri ous injury or death. • Do not spray ac ids, gasoline, ker o sene, or any...

Page 11 - Risk of bursting. Use a tire pressure gauge to check the; spray Wand nozzles; DO NOT attempt to increase pump pressure. A higher; Maintenance

11 E n g lis h WARNING: Risk of bursting. Use a tire pressure gauge to check the tires pressure before each use and while inflating tires; see the tire sidewall for the correct tire pressure. note: Air tanks, compressors and similar equipment used to inflate tires can fill small tires similar to the...

Page 12 - chanGInG nozzLes on sPraY WanD; chemicals and cleaning Solvents

12 E n g li sh nozzle color spray Pattern uses surfaces* red 0˚ powerful pinpoint for very intense cleaning metal or concrete; DO NOT use on wood Yellow 15˚ intense cleaning of small areas metal, concrete or wood Green 25 ˚ intense cleaning of larger areas metal, concrete or wood White 40 ˚ covers w...

Page 13 - Starting

13 E n g lis h 3. Install low-pressure (black) nozzle into quick connect fitting of spray wand, refer to spray Wand nozzles . note: Chemicals and soaps will not siphon if the black soap nozzle is not installed on the spray wand. 4. After use of chemicals, place chemical hose into container of clean ...

Page 14 - chemicals and cleaning solvents.; Shutting Down

14 E n g li sh 3. Connect the water hose to the water source. Turn the water source on to remove all air from the hose. When a steady stream of water is present, turn the water source off. 4. Verify the filter screen (U) is in water inlet of pump. U The cone side faces out. 5. Connect the cold water...

Page 15 - Storage; MAINtENANcE; to check oIL; hoW to chanGe PuMP oIL

15 E n g lis h NOTICE: Risk of property damage Failure to do so could cause damage to the pump. 2. Place the engine ON/OFF switch (H) to the OFF Position. 3. Place the fuel valve lever (M) in the OFF position. NOTICE: Risk of property damage. NEvER turn water supply off while pressure washer engine ...

Page 16 - Nozzle cleaning; to clean the Water Inlet Filter; Risk of property damage.

16 E n g li sh Nozzle cleaning If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instr...

Page 19 - chemicals and cleaning solvents

19 E n g lis h Glossary Bypass mode: Allows water to re-circulate within pump when the gun trigger is not pulled. chemical hose: Feeds cleaning agents into the pump to mix with the water. Refer to chemicals and cleaning solvents . chemical injection system: Mixes cleaners or cleaning solvents with w...

Page 20 - Problem; troubleshooting codes; coDe; hot

20 E n g li sh troubleshooting Guide This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified FNA technician or yo...

Page 21 - Operation

21 E n g lis h coDe PossIBLe cause PossIBLe soLutIon 8 Fuel valve closed. Move the fuel valve lever to the OPEN position. 9 Spray wand not in high pressure. See spray Wand nozzles under Operation . 10 Low water supply. Water supply must be at least 5 GPM @ 20 psi (138 kPa). 11 Leak at high-pressure ...