Dewalt DCN692-XE- Manuals

Page 2 - English; indicator lights; NAIL SPECIFICATIONS; Smooth and Ring; Defi nitions: Safety Guidelines; TOOL SPECIFICATIONS; Selective: Bump or Sequential

English 2 A. Trigger B. Trigger lock-off C. Depth adjustment wheel D. Low battery & jam/stall indicator lights E. Stall release lever F. Contact trip G. Magazine H. Pusher latch I. Bump/sequentialselector switch J. Rotating rafter/belt hook K. On-board hex wrench L. Battery Pack M. Dual speed sw...

Page 3 - IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D; General Power Tool Safety Warnings; ) POWER TOOL USE AND CARE; Nailer Safety Warnings

English 3 IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D E WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D E WALT (1-800-433-9258) . WARNING: To reduce the risk of injury, read the instruction manual. General Power Tool Safety Warnings WARNING! Read all safety warnings and all instructions. Fa...

Page 4 - Maintenance

English 4 • Use caution while removing a jammed fastener. The mechanism may be under compression and the fastener may be forcefully discharged while attempting to free a jammed condition. • Do not use this nailer for fastening electrical cables. It is not designed for electric cable installation and...

Page 6 - PACK CHARGING

English 6 The RBRC™ Seal The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the nickel cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate that the costs to recycle these batteries (or battery packs) at the end of their useful life have already been paid b...

Page 7 - Read the section titled; Important Charging Notes

English 7 6. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in t...

Page 8 - NEVER

English 8 Installing and Removing the Battery Pack (Fig. 3) NOTE: For best results, make sure your battery FIG. 3 L N pack is fully charged.To install the battery pack (L) into the tool handle, align the battery pack with the rails inside the tool’s handle and slide it into the handle until the batt...

Page 9 - Charging Procedures; UNLOADING THE TOOL; or

English 9 Preparing the Tool NOTICE: NEVER spray or in any other way apply lubricants or cleaning solvents inside the tool. This can seriously affect the life and performance of the tool. NOTE: The battery pack is not fully charged out of the carton. Follow instructions outlined (refer to Charging P...

Page 10 - Failure to do so may result in serious injury.; Prevents jams and premature failure of tool parts.; CHARGER CLEANING INSTRUCTIONS; spray or in any other way apply lubricants or cleaning

English 10 Stall Release (Fig. 12) If the nailer is used in harder wood where all available energy in the motor FIG. 12 E is used to drive a fastener, the tool may stall. The driver blade will not complete the drive cycle and the jam/stall indicator will flash. Rotate the stall release lever (E) on ...

Page 11 - DCN6901 RETURN SPRING REPLACEMENT KIT; Springs should be replaced as a pair, using only the correct D; Repairs; The charger and battery pack are not serviceable.

English 11 Accessories WARNING: Since accessories, other than those offered by D E WALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only D E WALT, recommended accessories should be used with this product. DCN6901 R...

Page 13 - TROUBLESHOOTING GUIDE; CONTACT A D; WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, ALWAYS; DISCONNECT BATTERY PACK FROM TOOL; BEFORE ALL REPAIRS; SYMPTOM

English 13 TROUBLESHOOTING GUIDE MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A D E WALT SERVICE CENTER OR CALL 1-(800)-4-D E WALT. WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, ALWAYS DISCONNECT BATTERY PACK FROM ...

Page 14 - Nail Specifications

English 14 SYMPTOM CAUSE FIX Tool operates but does not drive fasteners fully Depth adjust set too shallow Rotate depth adjust to a deeper setting. Tool not ﬁ rmly applied to workpiece Apply adequate force to tool securing it tightly to workpiece See instruction manual. Material and fastener length ...

Page 15 - WALT Battery and Charger Systems

D E WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (NOV13) Part No. N329480 DCN690, DCN692 Copyright © 2012, 2013 D E WALT The following are trademarks for one or more D E WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids ...