Dewalt D24000R - Manuals - manualsarea.com

Page 2 - WALT; IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

E n g li sh D E WALT… BUILT JOBSITE TOUGH D E WALT high performance industrial tools are made for America’s toughest industrial and construction applications. The design of every tool in the line – from drills to sanders to grinders – is the result of rigorous use on jobsites and throughout the indu...

Page 4 - WARNING: For your own safety, read the instruction manual before; Failure to heed these warnings may result in

E n g li sh 2 Important Safety Instructions for All Tools WARNING: For your own safety, read the instruction manual before operating the wet tile saw. Failure to heed these warnings may result in personal injury and serious damage to the saw. When servicing this tool, use only identical replacement ...

Page 6 - ON CUTTING WHEEL COVER; For further details, refer to; To Attach Cutting Wheel; in the; Quick Start Guide

E n g li sh 4 USE SPLASH GUARD FOR EVERY OPERATION FOR WHICH IT CAN BE USED. REPLACE DAMAGED CUTTING WHEEL BEFORE OPERATING.DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.NEVER USE PAN HEATER OR OTHER HEATER SOURCE FOR HEATING WATER. DAMAGE TO THE TOOL, FIRE OR PERSONAL INJURY COULD RESULT.THINK! YO...

Page 7 - lis; Assembly; For further details, refer; Adjustments; in; BB

E n g lis h 5 3. Attach the cutting cart to the rails. For further details, refer to Assembly in the Instruction Manual. NOTE: Make sure the cart lock is in full open position. a. Align the arrow on the rear of the cutting cart with the round rail on the frame of the saw. b. Place the rear roller as...

Page 8 - PP

E n g li sh 6 FEATURES (Fig. 2–4) The motor arm assembly comes assembled. Open the box and lift the assembly out, as shown in Figure 1. A On/Off switch I. Cutting cart water B. Motor arm assembly attachment C. Plunge handle J. Edge guide D. Head lock knob K. Water pan E. Cutting wheel cover L. Saw f...

Page 9 - CAUTION: Turn off and unplug the tool before mak-

E n g lis h 7 cutting wheel cover. Press the spindle lock button (U) while tightening the cutting wheel nut. 4. Replace cover and tighten screw (R).5. Adjust cutting wheel depth (see Cutting Depth Adjustment ). TO ATTACH THE EDGE GUIDE (FIG. 12) 1. Place edge guide (J) on the cutting cart assembly (...

Page 10 - CAUTION: Turn off and unplug the tool before

E n g li sh 8 3. Pull up the on/off switch (A) to turn the saw on. Wait until the stream of water from the water pump com- pletely covers the cutting wheel. NOTE: Cutting tile without water will damage the cut- ting wheel. 4. Ease the cutting cart toward the cutting wheel then slowly feed the tile i...

Page 11 - Do not attempt to move the saw while filled

E n g lis h 9 safe distance from the cutting wheel, lower the head of the saw slowly into the tile. Cut into the tile up to the edge of the mark without overcutting. 7. Repeat the process on each outline without overcut- ting. 8. Turn the tile over. Repeat steps 2 and 3, overcutting along the lines ...

Page 12 - NEVER spray or in any other way apply; BOTTOM; The use of any other accessory not recom-; YEAR FREE SERVICE

E n g li sh 10 MAINTENANCE Brushes (Fig. 18) CAUTION: Turn off and unplug the tool before mak- ing any adjustments or removing or installing attach- ments or accessories. Be sure the switch is in the OFF position. Inspect carbon brushes regularly by unplugging tool, removing the brush cap (OO) and w...

Page 13 - PERSISTENT PROBLEMS, CONTACT A D

E n g lis h 11 Troubleshooting Guide BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A D E WALT SERVICE CENTER OR CALL 1-(800)-4-D E WALT . TROUBLE! SAW WILL NOT START WHAT’S WRON...