Dewalt 7529- Manuals

Page 2 - Responsibility of the Owner; ROUTER TECHNOLOGIES; METRIC EQUIVILANTS FOR INTERNATIONAL CUSTOMERS; The following metric drill bit or wrench sizes may be substituted

This instruction manual covers several different makes and models of plunge routers. The instructions are written for a person with some mechanical ability. If you understand the parts and operation of a plunge router, installing the Router Raizer is not difficult. Before beginning installation comp...

Page 3 - READ THIS PAGE BEFORE INSTALLATION; Remove Pages From Book; Plunge Posts; Plunge Post Boots

© 2000-2005 Router Technologies All Rights Reserved Page 2 READ THIS PAGE BEFORE INSTALLATION FULL SIZE PARTS DIAGRAM ON BACK OF THIS PAGE ( PAGE 3 ) 3. Multiple Parts The Router Raizer is a universal kit containing many parts you will not install into your router. Each instruction page lists the pa...

Page 4 - Parts Shown Full Size

RZ 100 Parts Diagram Caution: Befor e and during installation of Router Raizer make sur e power switch is in the off position and tool is disconnected from power source to avoid accidental starting of t he tool which may r esult in personal injur y. © 2000-2005 Router Technologies All Rights Reserve...

Page 5 - Using the #46 Locating Pin; Locating Hole in Original Subbase; Preparing and Drilling Router Table Top; FROM TOP; SHOWN FROM BOTTOM SIDE; diameter hole drilled through the top of your router table

Page 4 METHOD #1 ( Drilling 3/4" Pocket in Back of Insert Plate requires min 3/8" thick plate ) Using the #46 Locating Pin Use this pin to simplify locating the Router Raizer access hole required through the original subbase or router table. Using fig 1 support router upside down on bench an...

Page 6 - Installing #30 Dust Cover Insert and #31 Dust Cover; Top; Mount router to insert plate and install into table

Page 5 Preparing and Drilling Router Table Top Method #2 (A ) and ( B ) METHOD #2 ( A ) Black Rubber spacer METHOD #2 ( B ) Routers Original Sub Base METHOD #2 ( A ) Black Rubber spacer METHOD #2 ( B ) Routers Original Sub Base © 2000-2005 Router Technologies All Rights Reserved Installing #30 Dust ...

Page 7 - Router table fence reference line; not counter sunk deep enough

Using Paper Drilling Template Troubleshooting © 2000-2005 Router Technologies All Rights Reserved Page 6 Refer to pages 4,5,6 before using template Additional Templates Available on Website Router Raizer Access Hole 3/4" reference circle for drilling therouters original subbase only. Tablemounte...

Page 8 - Router Raizer Use Instructions; Using Handheld; Dust Cover Insert and Dust Cover; Direction of Rotation for Adjustment; Transporting or Storing Router

Router Raizer Use Instructions Page 7 Using Handheld Using in a Router Table Caution: Always make sure router switch is in the off position, and tool is disconnected from power source when performing maintenance or making any adjustments to either the router or height adjustments to avoid accidental...

Page 9 - Place small amount of included red grease onto; See other side to finish installation.; ROUTER RAIZER PARTS REQUIRED:

Page 39 Porter Cable 7529 / 8529 1. Remove height knob assembly and dust shroud ( fig 1). Remove both brush covers ( fig 1 ) remove brushes one at a time, labeling the top and side of router removed from on each brush. 2. Remove four screws securing lower motor housing ( fig 2). Separate the upper a...

Page 10 - Sub-base Plate or Router Table Insert Plate Installation; Periodic inspection and re-greasing of #21 lead screw

Page 40 Porter Cable 7529 / 8529 Access hole Drill 3/4" 10. To ease router raizer adjustments, using fig ( 9 ) push the black plastic plunge lock lever towards the handle until it locks in the open position. The handle should remain unlocked. fig 9 #21 lead screw #19 short drive nut #23 O ring t...

Page 11 - Refer to pages 28, 31, 32 before using template; Router mounting holes

Porter Cable 7529 & 8529 Porter Cable 7529 & 8529 © 2000-2005 Router Technologies All Rights Reserved Note: Cross lines for locating and drilling holes are accurate. The illustration of subbase may vary slightly in size and design, but is accurate enough for cutting the rubber spacer if requ...