Page 2 - SAFETY GUIDELINES - DEFINITIONS; GENERAL SAFETY RULES
2 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in mi...
Page 3 - FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY, READ THE INSTRUCTIONMANUAL BEFORE OPERATING THE MACHINE. Learning the machine’s application, limitations, andspecific hazards will greatly minimize the possibility ofaccidents and injury. 2. WEAR EYE PROTECTION. ALWAYS USE SAFETYGLASSES. Also use face o...
Page 4 - ADDITIONAL SAFETY RULES FOR WOOD SHAPERS; SAVE THESE INSTRUCTIONS; Refer to them often
4 04-24-03 1. DO NOT OPERATE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBTAIN ADVICE from your supervisor, instructor, oranother qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES and recommended electrical...
Page 5 - FOREWORD
5 Do not expose this machine to rain or operate the machine in damp locations. POWER CONNECTIONS MOTOR SPECIFICATIONS This machine is not supplied with a power cord, and must be be permanently connected to the building electricalsystem and grounded according to the National Electrical Code and/or lo...
Page 6 - ATTACHING SPINDLE RAISING AND LOWERING HANDWHEEL; ASSEMBLY; ATTACHING EXTENSION WING TO SHAPER TABLE
6 For your own safety, do not connect the machine to the power source until the machine iscompletely assembled, and you read and understand the entire instruction manual. ATTACHING SPINDLE RAISING AND LOWERING HANDWHEEL 1. Insert the key (A) Fig. 1 into the slot in the spindle raising and lowering s...
Page 7 - ATTACHING SPINDLE GUARD
7 Fig. 8 ATTACHING TABLE INSERTS Three table inserts are provided for various size cutters (Fig. 8). The large insert is adjustable.To set it flush with the table: 1. Remove the three slotted head screws (A) Fig. 8. 2. Use a screwdriver to turn the three adjusting screws (B) Fig.8 until the insert i...
Page 8 - ATTACHING ELECTRICAL BOX TO CABINET; OPERATING CONTROLS AND ADJUSTMENTS; STARTING AND STOPPING THE SHAPER; CHANGING SPEEDS AND ADJUSTING BELT TENSION
8 ATTACHING ELECTRICAL BOX TO CABINET The tool is shipped with the starter box wired to the switch and motor and must bemounted to the shaper cabinet. Install three 1/4-20 x 1/2" hex head screws with lockwashers through the rear of thetool (A) Fig. 15, and into the tapped holes (B) on the back o...
Page 9 - REVERSING SPINDLE ROTATION; OPERATIONS; SHAPING WHEN USING THE FENCE AS A GUIDE
9 Using the fence is the safest and most satisfactory method of shaping. Most straight work can be shaped using the fencedescribed below.1. For average work, where a portion of the original edge ofthe work is not touched by the cutter, both the front andrear fences are in a straight line (Fig. 21). ...
Page 10 - POSITION OF COLLARS; END SHAPING; CROSS GRAIN SHAPING
10 POSITION OF COLLARS 1. The collars may be used in any of three positions:above, below, or between two cutters. 2. When the collar is used below the cutter (Fig. 29), theoperator can see the progress of the cut. NOTE : Any accidental lifting of the work will gouge the wood andruin the workpiece. 3...
Page 11 - STARTING PIN; REPLACING SPINDLE CARTRIDGE
11 STARTING PIN 1. The machine is supplied with a tapered starting pin (A)Fig. 34, which is used as a support when starting thecut. The starting pin (A) is placed in one of the taperedholes (B) in the table. 2. Place the work in the first position using the guide pinas a support (Fig. 35). Swing the...
Page 12 - PARTS, SERVICE OR WARRANTY ASSISTANCE; ACCESSORIES
12 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality pro...
Page 13 - Two Year Limited New Product Warranty
13 Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessorywhich in normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a Delt...
Page 14 - NOTES
Page 16 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...