Dewalt 36-600 - Manuals

6 1 - Table Saw 2 - Extension Wing (2) 3 - Rip Fence 4 - Miter Gage 5 - Rip Fence Handle 6 - Handwheel (2) 7 - Handwheel Lock Knob (2) * - Washer (2), Not Shown Used to mount handwheel lock knob Fig. 1 UNPACKING AND CLEANING Carefully unpack the tool, stand and all loose items from the carton. Remov...

9 ASSEMBLING SAWTO STAND 1. Position the saw (B) on the stand as shown in Fig. 6, lining up the four holes on the bottom of sides of the sawcabinet with the four holes in the two top side braces,one of which is shown at (A). 2. Fasten the saw to the stand using the four 16MM long hex head screws, ei...

11 Fig. 11 Fig. 12 Fig. 13 5. Using the open end wrench (F) Fig. 11 and Fig. 12, supplied, place the wrench (F) on the flats on the sawarbor to keep the arbor from turning and tighten arbornut (E) (turn counterclockwise) using the remainingwrench (G) Fig. 12. 6. Replace table insert (A) Fig. 13, mak...

13 Fig. 18 Fig. 19 Fig. 20 Fig. 21 5. Assemble longer section of rear guide rail (P) Fig. 18, and shorter section of guide rail (R) to extension wingsand saw table at points (A) with 16MM long hex headscrew (S), two flat washers (T), lockwasher (V), and hexnut (W); and at points (B) and (C) Fig. 18,...

16 FASTENING STAND TO SUPPORTING SURFACE IF DURING OPERATION THERE IS ANY TENDENCY FOR THE TOOL TO TIP OVER, SLIDE OR WALK ON THESUPPORTING SURFACE, REMOVE THE RUBBER FEET FROM THE STAND AND SECURE THE STAND TO THEFLOOR. OPERATING CONTROLS AND ADJUSTMENTS STARTING ANDSTOPPING SAW The switch (A) is l...

17 ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS Your saw is equipped with positive stops that will position the saw blade at 90 and 45 degrees to the table. To checkand adjust the positive stops, proceed as follows: 1. DISCONNECT THE TOOL FROM THE POWER SOURCE. 2. Turn the blade tilting handwheel count...

19 Fig. 44 Fig. 45 Fig. 46 Fig. 47 1. Your miter gage is equipped with individually adjust- able index stops at 90 degrees and 45 degrees right andleft. Adjustment to the index stops can be made byloosening lock nuts (A) Fig. 44, and tightening orloosening the three adjusting screws (B) against the ...

20 20 RIPPING Fig. 48 TYPICAL OPERATIONS CROSS-CUTTING Cross-cutting requires the use of the miter gage toposition and guide the work. Place the work against themiter gage and advance both the gage and work towardthe saw blade, as shown in Fig. 48. The miter gage maybe used in either table slot. Whe...

23 Fig. 59 Fig. 60 USING AUXILIARY WOODFACING ON RIP FENCE It is necessary when performing special operations suchas when using the moulding cutterhead to add woodfacing (A) Fig. 59, to one or both sides of the rip fence,as shown. The wood facing is attached to the fence withwood screws through the ...

24 CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be madefrom scrap material by following the pattern shown in Fig. 61. CUT OFF HERE TO PUSH 1/4 ″ WOOD CUT OFF HERE TO PUSH 1/2 ″ WOOD 1/2 ″ SQUARES NOTCH TO HELP ...

25 Fig. 62 Fig. 63 Fig. 64 MAINTENANCE CHANGING THE BLADE 1. MAKE CERTAIN THE TOOL IS DISCONNECTED FROM THE POWER SOURCE. USE ONLY 10 ″″ DIAMETER SAW BLADES RATED FOR 5500 RPM OR HIGHERWITH 5/8" ARBOR HOLES. 2. Raise saw blade to its maximum height and remove the table insert (A) Fig. 62. NOTE: ...

26 26 Fig. 65 Fig. 67 Fig. 66 BELT REPLACEMENT Should you find it necessary to replace the belt on yoursaw, proceed as follows: 1. DISCONNECT THE TOOL FROM THE POWER SOURCE. 2. Raise the saw blade to its maximum height and remove the blade guard and splitter, table insert and sawblade. Tilt the arbo...

Delta Building Trades and Home Shop Machinery Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven to be defective in workmanship or material, provided that the customer returns t...