Definitive Technology DYMENSIONDM10 - Manuals

5 Product specifications Every speaker in the Dymension series is covered with a non-removeable, acoustically transparent black cloth. See below for more technical specifications and details. Tower speakers DM80 DM70 DM60 DM40 Dimensions 49.4 x 11.3 x 16.0 in. (1254.9 x 286.7 x 406.7 mm) 47.4 x 11.3...

7 DM90 DM95 Dimensions 6.0 x 7.3 x 15.3 in. (151.6 x 185.2 x 388.7 mm) 8.3 x 7.3 x 13.0 in. (210.7 x 184.2 x 330.2 mm) Tweeter (1) 1 in. aluminum oxide dome (1) 1 in. aluminum oxide dome Midrange/ Midbass (1) 5.25 in. BDSS with Linear Response Waveguide (1) 5.25 in. BDSS with Linear Response Wavegui...

8 Tower speaker back panels 12 3 5 6 1 2 3 5 6 7 1 - 2 - 3 - 4 - 5 - 6 -7 - Height-channel binding posts: Connect to an amplifier or receiver when the optional DM90 speaker is installed. Status light: The light turns from red to blue when the speaker receives a signal from your amplifier or receiver...

10 Center speaker back panels 1 - 2 - 3 -4 - Status light: The light turns from red to blue when the speaker receives a signal from your amplifier or receiver. For more information, see page 26. Intelligent Bass Control knob: Increases or decreases the bass level. We recom- mend starting at the 12-o...

13 Speaker Placement Correct speaker placement is important to maximize the sound quality of your audio system. Read this section for placement tips for your individual speakers, as well as diagrams and descriptions of various speaker system layouts. Positioning the speakers Tower speakers The tower...

15 Surround and height speakers You can use the DM95 speakers as surround or height speakers. Review the Quick Start Guide that came with the product for installation instructions. See below for additional placement advice, depending on your setup.For more information about using and positioning hei...

16 Speaker system setups Your Dymension speakers are compatible with 2, 3, 5, 7, and 9-channel surround sound configurations and all Dolby Atmos setups (for example, 5.1.2, 5.1.4, etc). Take a look at the following examples and give them a try based on the Dymension speakers you have. Note: You can ...

17 Listening in a 5-channel configuration 90º TV 90º 20º 20º CENTER FRONT LEFT FRONT RIGHT You can use DM95 speakers as rear surround speakers to create a home theater sur- round system. Ideal rear channel placement is along a side wall, slightly behind and above the listening position. Note: If you...

18 Speaker Wiring All of the Dymension series speakers use the same binding posts that can be un- screwed and then tightened to connect bare speaker wire. You can also attach a banana plug or spade connector to connect wire to the binding posts. See the next sections for wiring illustrations. To con...

19 The DM70 and DM80 speakers come with more than one set of binding posts. As seen in the diagrams, the bottom pair of binding posts connect the main speaker array. The top pair of binding posts are used to connect a DM90 height module to your receiver. For more information about the other binding ...

20 The Rear Speaker Array The Dymension tower speakers each come with a rear speaker array. These speakers can be adjusted down if there is too much spatial effect. DM70, DM60, and DM40 use a switch to adjust the level of the rear tweeter. DM80 uses a jumper cable to attenuate the entire array. How ...

21 Adjusting the rear array setting DM40, DM60, and DM70: Flip the rear tweeter switch on the back of the speaker to switch between 0dB (full bi-polar) and -6dB (forward focus) mode on the rear tweeter. DM80: Move the top red jumper cable between the 0dB (default) and -6dB binding posts to switch be...

22 Installing Height Speakers The Dymension Series offers two ways to add height channels to your speaker system—connect DM90 height speakers to your tower speakers or install DM95 surround speakers. Installing DM90 speakers You can add a DM90 height speaker to your DM80 or DM70 tower speaker. The h...

23 1. Remove the top plate from the tower speaker by pushing down on the right side and then pulling up and removing the plate. 2. Align the DM90 speaker with the top of the tower speaker and place it firmly onto the speaker making sure the connector on the bottom of the DM90 is seated into the towe...

24 Settings and Configuration Receiver recommendations Playing Dolby Atmos or DTS:X content You can take full advantage of the Dymension sound technology by playing or streaming content that is Dolby Atmos or DTS:X encoded. Note: Reference your receiver/processor owner’s manual for complete directio...

25 Powering the active subwoofer The DM80, DM70, DM60, and DM30 speakers contain built-in powered subwoofers that must be plugged into an electrical socket. Bass management When using your Dymension speakers with a receiver or processor employing bass management, make sure to adjust the bass managem...

26 Crossover points These are recommended nominal crossover points. Crossover points above or below these might work better in certain situations. Experiment with values +/-20Hz from the nominal to find the best results. Speaker Crossover Point DM10 80 Hz DM20 90 Hz DM30 60 Hz DM40 60 Hz DM80, DM70,...

27 DM80 Wiring Configurations You can take advantage of seven different wiring configurations for your DM80 tower speakers. This includes full bi-polar or forward-focused configurations for standard wiring, bi-wiring, and bi-amping. Any wiring configuration can be used, depending on your speaker set...

29 Bi-amping | Bi-polar Remove both jumper cables. Connect speaker wires from one output on your am- plifier or AVR to the Speaker Input binding posts on the speaker. Connect speaker wires from the bottom two Rear Input binding posts on the speaker to a different set of binding posts designated for ...

31 Speaker Feet Pads and Spikes Dymension tower speakers come pre-installed with a set of foot pads that can be screwed on and off. Keep these pads on the speaker if you place it on a hard surface, such as hardwood, concrete, tile, etc. If you place the speaker on carpet, we recom- mend that you ins...

32 Tips and Troubleshooting If you experience any difficulties with your speakers, try the suggestions below. If you still have problems, contact your Definitive Technology Authorized Dealer. There is audible distortion when the speakers play at loud levels. Audible distortion when the speakers are ...

33 The status light on the back of my speaker is blinking red. If the status light is blinking red, the integrated amplifier is in protect mode. Please discontinue use of the product and contact customer service by visiting https:// support.definitivetechnology.com/ . For more information about the ...

34 Dolby, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Copyright © 2012-2021 Dolby Laboratories. All rights reserved. For DTS patents, see http://patents.dts.com. Manufactured under lic...