Daewoo DP-HG22 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS

1 TABLE OF CONTENTS 1. Check for enclosed parts .............................. 2 2. Important Safety Instructions ........................ 3 3. Assembly Instructions ................................... 6 4. Adjusting angles after installation ................12 * To install the wall hanger unit, Ple...

Page 3 - PLASMA DISPLAY HANGER UNIT; PLEASE CHECK THE ITEMS SHOWN BELOW

PLASMA DISPLAY HANGER UNIT 2 H WA AN LG LE R UNIT 1. PLEASE CHECK THE ITEMS SHOWN BELOW (2) FRAME SET A FRAME SET B CONNECTING FRAME CONCRETE WALL ANCHOR M5 SCREWS (20 MM) WALL SCREWS PAPER PATTERN PLAN M5 SCREWS (30MM) (2) (1) (8) (12) (8) (1) (2) Paper pattern plan

Page 4 - IMPORTANT SAFETY INSTRUCTIONS; the unit and can result in injury or damage to the unit.; PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY

3 2. IMPORTANT SAFETY INSTRUCTIONS WARNING : Disregarding these instructions can result in serious injury. CAUTION : Disregarding these instructions will result in the mistreatment of the unit and can result in injury or damage to the unit. PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVE...

Page 7 - ASSEMBLING INSTRUCTIONS; PREPARATION; WHEN THE PLASMA DISPLAY IS ATTACHED TO THE STAND

PLASMA DISPLAY HANGER UNIT 6 H WA AN LG LE R UNIT 3. ASSEMBLING INSTRUCTIONS PREPARATION WHEN THE PLASMA DISPLAY IS ATTACHED TO THE STAND TO DETACH THE STAND FROM THE PLASMA DISPLAY TO PLACE THE PROTECTIVE CAPS . To avoid unwanted marks on the unit, placea protective covering over the surface youwil...

Page 8 - CORRIGENDA; Four M5 screws are not used out of total number.

7 INSTALLING THE W ALL FRAME SET A ON THE PLASMA DISPLAY PANEL HOW T O INSTALL FRAME SET A ON THE UNIT . To avoid unwanted marks on the unit, placea protective covering over the surface youwill be working on and lay the plasma displayas shown in the picture below. . When securing frame set A to the ...

Page 9 - INSTALLING WALL FRAME SET B AND CONNECTING FRAME

PLASMA DISPLAY HANGER UNIT 8 H WA AN LG LE R UNIT INSTALLING WALL FRAME SET B AND CONNECTING FRAME INSTALLING WALL FRAME SET B AND CONNECTING FRAME. ATTACHING PAPER PATTERN PLAN ON THE WALL . Place frame set B on the left and right side ofthe unit and use the enclosed screws (M5) tosecure them tight...

Page 10 - INSTALL THE WALL FRAME SET ON THE WALL; INSTALLING ON THE WALL HELD BY SUPPORTING WOODEN STRUCTURE

9 INSTALL THE WALL FRAME SET ON THE WALL . Install the wall frame set on the wall by matching the concrete anchors with the holes,then use the wall screws (8) to secure tightly. Paper pattern plan 3 INSTALLING ON THE WALL HELD BY SUPPORTING WOODEN STRUCTURE . If it is not feasible to attach frame se...

Page 11 - CONNECTING UPPER PART OF FRAME SET A AND FRAME SET B; At least two people are needed to put these frames together.; CONNECTING LOWER PART OF FRAME SET A AND FRAME SET B

CONNECTING UPPER PART OF FRAME SET A AND FRAME SET B . Insert the upper part of frame set A (X) to frameset B (Y) as indicated below. * At least two people are needed to put these frames together. (X) (Y) (Z) Frame set B Frame set A 1 PLASMA DISPLAY HANGER UNIT 10 H WA AN LG LE R UNIT CONNECTING LOW...

Page 12 - TO PROVIDE THE SECUREST FIT

11 TO PROVIDE THE SECUREST FIT . After installing plasma display and wall frame sets, for a more secure fit, secureM5 screws (M5x30) on the (Z) part so that (Z) will not move up and down asshown in the picture below. 3

Page 13 - HOW TO ADJUST VIEWING ANGLES; THE FIGURES BELOW DISPLAY THE POSSIBLE PLASMA DISPLAY ANGLES.

PLASMA DISPLAY HANGER UNIT 12 H WA AN LG LE R UNIT 4. ADJUSTING ANGLES AFTER INSTALLATION (10˚, 15˚, 20˚) HOW TO ADJUST VIEWING ANGLES THE FIGURES BELOW DISPLAY THE POSSIBLE PLASMA DISPLAY ANGLES. . Take out the screws from the upper part of the frame. . Insert the upper part of the frame set B angl...