Dacor EF42DBSS - Manuals

3 Location Requirements Your Dacor refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator. IMPORTANT: Observe all governing codes and ordinances. ƒ It is recommended that you do not install the refrigerator ...

4 Electrical Requirements Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection. Recommended Grounding Method A 115 Volt, 60 Hz., AC only 15 or 20-amp fused, grounded electrical supply is required. It is recommended that a s...

5 Installation Requirements If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa): Check to see whether the sediment filter in the reverse ƒ osmosis system is blocked. Replace the filter if necessary. Allow the storage tank on the reverse osmosis system to re...

6 Product Dimensions Side View: The depth from the front of the top grille to the back of the ƒ refrigerator cabinet is 25³⁄ 8 ” (64.5 cm). The power cord is 84” (213 cm) long. ƒ The water line attached to the back of the refrigerator is 5 ft ƒ (1.5 m) long. Height dimensions are shown with leveling...

7 130 ˚ 130 ˚ 90 ˚ 90 ˚ 110 ˚ 110 ˚ 50 ¹ ⁄ 2 " (128.3 cm) 45 ¹⁄ 4 " (114.9 cm) 26 ³⁄ 4 " (68.0 cm) 19 ³⁄ 4 " (50.2 cm) 40" (101.6 cm) 43 ¹ ⁄ 2 " (110.5 cm) Door Swing Dimensions The location must permit both doors to open to a minimum of 90°. Allow 4½” (11.4 cm) minimum space...

8 Bac ker P anel Overla y P anel Spacer Panel 1 / 4 " (6.4 mm) 3 / 4 " (1.9 cm) 1" (2.5 cm) 1 / 2 " (1.3 cm) 1" 1 1 / 4 " 1 1 / 2 " 1" (2.5 cm) 1 (3.2 cm) 1 / 4 " 1 (3.8 cm) 1 / 2 " 1 / 2 " RefrigeratorSide Trim Door Hinge (2.5 cm) (3.2 cm) (3.8 cm) (1.3 c...

10 Custom overlay panels used with models IF42 and IF48 allow you to blend the exterior of your refrigerator into the overall kitchen décor, and to use custom handles for additional design flexibility. Panel Specifications The custom panels must have backer panels attached in order • to mount them t...

11 Installation Requirements Decorative Overlay Panels Model Series A B C IF42 17¹⁄ 8 ” (43.5 cm) 23¹⁄ 8 ” (58.74 cm) 40½” (102.9 cm) IF48 19 5 ⁄ 8 ” (49.9 cm) 26 5 ⁄ 8 ” (67.6 cm) 46½” (118.1 cm) Backer Panels Model Series D E F IF42 16 7 ⁄ 8 ” (42.9 cm) 22 7 ⁄ 8 ” (58.1 cm) 40½” (102.9 cm) IF48 19...

12 Installation Requirements Custom Side Panels - IF42/IF48 Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset or Recessed Inset panel installat...

14 Unpack Refrigerator IMPORTANT: If you receive a damaged product, immediately contact your ƒ dealer or builder. Do not install or use a damaged appliance. Do not remove the film on the outside until the refrigerator is in ƒ its operating position. All four leveling legs must contact the floor to s...

15 Installation Instructions Install Anti-Tip Boards IMPORTANT : To avoid tipping during use, the solid soffit must be within 1” ƒ (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1” (2.5 cm) or one is not available, then the refrigerator must be braced. It is recommended ...

16 Installation Instructions Using a cordless drill, drill a ¼” (6.35 mm) hole in the cold 5. water pipe you have selected. Fasten the shutoff valve to the cold water pipe with the pipe 6. clamp. Be sure the outlet end is solidly in the ¼” (6.35 mm) drilled hole in the water pipe and that the washer...

17 WARNING Tip Over Hazard Refrigerator is top heavy and tips easily when not completely installed. Keep doors taped closed until refrigerator is completely installed.Use two or more people to move and install refrigerator.Failure to do so can result in death or serious injury. Continue adjusting al...

18 IMPORTANT : Install the custom handles prior to installing the panels on the ƒ refrigerator. Create custom door overlay panels according to the ƒ specifications in the Custom Panels and Handles section. Dacor is not responsible for customer installed molding or ƒ decorative panels that need to be...

19 After adjusting, check the doors to make sure they are even at 4. the top and bottom. If the doors are not even, continue to turn the bushing to adjust the door height. Replace the locking plate. 5. Turn the bushing slightly to align the hinge and locking plate 6. screw holes. Replace the door st...

20 Using the two screws, attach the base grille assembly to the 5. refrigerator as shown. Install the water filter and rotate it one-quarter turn to the right. 6. It may be hard to turn. The cap should be in the horizontal position. Trim the skirt by scoring the 4. proper “V” groove with a utility k...

21 Complete Installation Turn the water supply line valve to the “Open” position. 1. Turn the refrigerator switch to the ON position. See 2. Power On/ Off Switch in the use and care manual for instructions. Wait a few minutes. Check the water line connections for leaks. Remove all boxes, parts packa...