D-Link GO-RT-AC750 - Manuals

2 D-Link GO-RT-AC750 User Manual Section 1 - Product Overview Network Requirements • An Ethernet-based Cable or DSL modem • IEEE 802.11ac, 802.11a, 802.11n or 802.11g wireless clients • 10/100 Ethernet Web-based Configuration Utility Requirements Computer with the following: • Windows®, Macintosh, o...

3 D-Link GO-RT-AC750 User Manual Section 1 - Product Overview Introduction The D-Link GO-RT-AC750 is a IEEE 802.11ac compliant device that delivers up to 3 times faster speeds than 802.11n while staying backward compatible with 802.11a/g/b devices. Connect the GO-RT-AC750 to a Cable or DSL modem and...

4 D-Link GO-RT-AC750 User Manual Section 1 - Product Overview • Ultimate Fast Wireless Networking - The GO-RT-AC750 provides up to 300 Mbps wireless connection in 2.4 GHz band, 433 Mbps wireless connection in 5 GHz with other 802.11ac and draft 802.11n wireless clients. This capability allows users ...

5 D-Link GO-RT-AC750 User Manual Section 1 - Product Overview 1 2 3 4 Hardware Overview Connections 1 Reset Button Insert a paperclip in the hole and wait for 10 seconds to reset the router to default settings. 2 LAN Ports (1-4) Connect 10/100 Ethernet devices such as computers, switches, storage (N...

6 D-Link GO-RT-AC750 User Manual Section 1 - Product Overview Hardware Overview LEDs 1 Power LED A solid green light indicates a proper connection to the power supply. 2 Internet LED A solid light indicates connection on the Internet port. 3 WPS LED This LED blinks during WPS handshake phase. 4 Wire...

7 D-Link GO-RT-AC750 User Manual Section 2 - Installation Before you Begin Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. • Please c...

8 D-Link GO-RT-AC750 User Manual Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thic...

9 D-Link GO-RT-AC750 User Manual Section 2 - Installation 1. Turn off and unplug your cable or DSL broadband modem. This is required. Manual Setup 2. Position your router close to your modem and a computer. Place the router in an open area of your intended work area for better wireless coverage. 3. ...

10 D-Link GO-RT-AC750 User Manual Section 2 - Installation 4. Plug one end of the included blue Ethernet cable that came with your router into the yellow port labeled INTERNET on the back of the router. Plug the other end of this cable into the Ethernet port on your modem. 5. Reconnect the power ada...

11 D-Link GO-RT-AC750 User Manual Section 3 - Configuration There are several different ways you can configure your router to connect to the Internet and connect to your clients: • D-Link Setup Wizard - This wizard will launch when you log into the router for the first time. Refer to page12. • QRS M...

12 D-Link GO-RT-AC750 User Manual Section 3 - Configuration If this is your first time logging into the router, this wizard will start automatically. This wizard is designed to guide you through a step-by-step process to configure your new D-Link router and connect to the Internet. Click Next to con...

13 D-Link GO-RT-AC750 User Manual Section 3 - Configuration If the router does not detect a valid Ethernet connection from the Internet port, this screen will appear. Connect your broadband modem to the Internet port and then click Try Again . If the router detects an Ethernet connection but does no...

14 D-Link GO-RT-AC750 User Manual Section 3 - Configuration If the router detected or you selected PPPoE , enter your PPPoE username and password and click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a...

15 D-Link GO-RT-AC750 User Manual Section 3 - Configuration If the router detected or you selected Static , enter the IP and DNS settings supplied by your ISP. Click Next to continue. For both the 2.4GHz and 5GHz segments, create a Wi-Fi network name (SSID) using up to 32 characters. Create a Wi-Fi ...

17 D-Link GO-RT-AC750 User Manual Section 3 - Configuration QRS Mobile app allows you to install and configure your router from your mobile device. Step 1 Search for the free QRS Mobile App on the iTunes Store or Google Play. Step 2 Once your app is installed, you may now configure your router. Conn...

18 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Step 4 You will see the welcome screen. Tap Start to proceed, then enter your device password and tap Log In . Tap Next once the Operation Mode screen appears. Step 5 At this point, please ensure that you the router is connected to a modem....

20 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Step 8 If you wish to receive push notifications whenever a new firmware update is available, check the Notify me when new firmware is available box and tap Next . Otherwise, just tap Next to proceed. Step 9 You will be presented with a sum...

21 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Congratulations, your device has been successfully configured! You can share this information by tapping Share By NFC , Share By E-mail , or tap Finish to exit the app. If you tap Share By NFC, you can now touch the tag with your other devi...

22 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Web-based Configuration Utility Leave the password blank by default. To access the configuration utility, open a web-browser such as Internet Explorer and enter address of the router ( http://dlinkrouter.local./ or http://192.168.0.1 ). Non...

23 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Internet Connection Setup Click Manual Internet Connection Setup to configure your connection manually and continue to the next page. If you want to configure your router to connect to the Internet using the wizard, click Internet Connectio...

24 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Internet Connection Setup Wizard When configuring the router for the first time, we recommend that you click use the Internet Connection Setup Wizard , and follow the instructions on the screen. This wizard is designed to assist user with a...

32 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Select Static IP to manually enter the IP settings supplied by your ISP. Enter the IP address assigned by your ISP. Enter the Subnet Mask assigned by your ISP. Enter the Gateway assigned by your ISP. The DNS server information will be suppl...

33 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Internet Setup PPPoE (DSL) Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove...

35 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Internet Setup PPTP Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. My Internet Connection: Select ...

37 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Internet Setup L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. My Internet Connection: Select L2TP (Us...

39 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Internet Setup DS-Lite Another Internet Connection type is DS-Lite. DS-Lite is an IPv6 connection type. After selecting DS-Lite, the following parameters will be available for configuration: DS-Lite Configuration: Select the DS-Lite DHCPv6 ...

40 D-Link GO-RT-AC750 User Manual Section 3 - Configuration On this page the user can configure the Wireless settings for this device. There are 3 ways to configure Wireless using this router. Firstly, the user can choose to make use for the quick and easy Wireless Connection Setup Wizard . Secondly...

43 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Wireless Settings: Wi-Fi Protected Setup Wizard If your Wireless Clients support the WPS connection method, this Wi-Fi Protected Setup Wizard can be used to initiate a wireless connection between this device and Wireless clients with a simp...

44 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Step 2: After selecting Manual, the following page will appear. On this page to user can view the wireless configuration of this router. The wire- less clients should configure their wireless settings to be identical to the settings display...

53 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The GO-RT-AC750 offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared ...

54 D-Link GO-RT-AC750 User Manual Section 3 - Configuration This section will allow you to change the local network settings of the router and to configure the DHCP settings. Network Settings Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, onc...

55 D-Link GO-RT-AC750 User Manual Section 3 - Configuration DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The GO-RT-AC750 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your compute...

57 D-Link GO-RT-AC750 User Manual Section 3 - Configuration DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within th...

58 D-Link GO-RT-AC750 User Manual Section 3 - Configuration IPv6 On this page, the user can configure the IPv6 Connection type. There are two ways to set up the IPv6 Internet connection. You can use the Web-based IPv6 Internet Connection Setup Wizard, or you can manually configure the connection. Fo...

64 D-Link GO-RT-AC750 User Manual Section 3 - Configuration IPv6 Manual Setup There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6), PPPoE, IPv6 in IPv4 Tunnel, 6to4, 6rd, and Link-local. If you are unsure of your connection method, please c...

66 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Autoconfiguration Select Autoconfiguration (Stateless/DHCPv6) from the drop-down menu. Select either Obtain DNS server address automatically or Use the following DNS Address . Enter the primary and secondary DNS server addresses. Enter the ...

69 D-Link GO-RT-AC750 User Manual Section 3 - Configuration IPv6 in IPv4 Tunneling Select IPv6 in IPv4 Tunnel from the drop-down menu. Enter the settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address. Check t...

70 D-Link GO-RT-AC750 User Manual Section 3 - Configuration 6 to 4 Tunneling Select 6 to 4 from the drop-down menu. Enter the IPv6 settings supplied by your Internet provider (ISP). Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the ...

72 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Select Link-Local Only from the drop-down menu. Displays the IPv6 address of the router. My IPv6 Connection: LAN IPv6 Address Settings: Link-Local Connectivity

73 D-Link GO-RT-AC750 User Manual Section 3 - Configuration This will allow you to open a single port. If you would like to open a range of ports, refer to the next page. Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate ...

74 D-Link GO-RT-AC750 User Manual Section 3 - Configuration This will allow you to open a single port or a range of ports. Port Forwarding Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. Enter the IP address...

75 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Enter a name for the rule. You may select a pre-defined application from the drop-down menu and click << . This is the port used to trigger the application. It can be either a single port or a range of ports. Select the protocol of th...

76 D-Link GO-RT-AC750 User Manual Section 3 - Configuration QoS Engine The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically. The QoS section contains ...

78 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Network Filters Select Turn MAC Filtering Off , Allow MAC addresses listed below , or Deny MAC addresses listed below from the drop-down menu. Enter the MAC address you would like to filter. To find the MAC address on a computer, please ref...

79 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Access Control Click the Add Policy button to start the Access Control Wizard. Add Policy: The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to app...

80 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Enter a name for the policy and then click Next to continue. Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue. Enter the following information and then click Next to continue. • Address Type - Select I...

81 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Enter the rule: Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the star...

82 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Add Website Filtering Rule: Website URL/ Domain: Website Filters Select either DENY computers access to ONLY these sites or ALLOW computers access to ONLY these sites . Enter the keywords or URLs that you want to allow or block. Click Save ...

83 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Enter a name for the inbound filter rule. Select Allow or Deny . Check to enable rule. Enter the starting IP address. Enter 0.0.0.0 if you do not want to specify an IP range. Enter the ending IP address. Enter 255.255.255.255 if you do not ...

84 D-Link GO-RT-AC750 User Manual Section 3 - Configuration SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol. Enable this feat...

86 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Enter a name for your route. Enter the IP address of packets that will take this route. Enter the netmask of the route, please note that the octets must match your destination IP address. Enter your next hop gateway to be taken if this rout...

87 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Advanced Wireless Set the transmit power of the antennas. This enables 802.11d operation. 802.11d is a wireless specification developed to allow implementation of wireless networks in countries that cannot use the 802.11 standard. This feat...

88 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Wi-Fi Protected Setup (WPS) Enable the Wi-Fi Protected Setup feature. Note: if this option is unchecked, the WPS button on the side of the router will be disabled. Tick this option to lock the configured wireless security settings. A PIN is...

90 D-Link GO-RT-AC750 User Manual Section 3 - Configuration To use the Universal Plug and Play (UPnP ™ ) feature click on Enabled . UPnP provides compatibility with networking equipment, software and peripherals. Checking the box will allow the GO-RT-AC750 to respond to pings. Unchecking the box may...

91 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Guest Zone Check to enable the Guest Zone feature. The schedule of time when the Guest Zone will be active. The schedule may be set to Always , which will allow the particular service to always be enabled. You can create your own times in t...

92 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Admin This page will allow you to change the Administrator and User passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser. The accounts are admin and user. ...

93 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Time Displays the current date and time of the router. Select your Time Zone from the drop-down menu. To select Daylight Saving time manually, select enabled or disabled, and enter a start date and an end date for daylight saving time. NTP ...

94 D-Link GO-RT-AC750 User Manual Section 3 - Configuration SysLog The Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a SysLog server on your network. Enable Logging to SysLog Server: SysLog Server IP Address: Check this box to send ...

95 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Email Settings The Email feature can be used to send the system log files, router alert messages, and firmware update notification to your email address. Enable Email Notification: From Email Address: To Email Address: SMTP Server Address: ...

96 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Use this option to save the current router configuration settings to a file on the hard disk of the computer you are using. First, click the Save button. A file dialog will appear, allowing you to select a location and file name for the set...

97 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Firmware Browse: Upload: After you have downloaded the new firmware, click Browse to locate the firmware update on your hard drive. Click Upload to complete the firmware upgrade. Once you have a firmware update on your computer, use this op...

98 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. Check the box to enable DDNS. Select your DDNS provider from the drop-down menu or enter the DDNS server address. Enter the Host Name that you ...

99 D-Link GO-RT-AC750 User Manual Section 3 - Configuration The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP address that you wish to Ping and click Ping . Enter the IPv6 address that you wish to Ping and click Ping . The results of your ping attempts...

100 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Enter a name for your new schedule. Select a day, a range of days, or All Week to include every day. Check All Day - 24hrs or enter a start and end time for your schedule. You must click Save Settings at the top for your schedules to go in...

101 D-Link GO-RT-AC750 User Manual Section 3 - Configuration This page displays the current information for the GO-RT-AC750. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will...

102 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Logs Log Options: Refresh: First Page: Last Page: Previous: Next: Clear: Email Now: Save Log: You can select the types of messages that you want to display from the log. System Activity, Debug Information, Attacks, Dropped Packets, and Not...

103 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Statistics The screen below displays the Traffic Statistics . Here you can view the amount of packets that pass through the GO-RT-AC750 on both the WAN, LAN ports and the wireless segments. The traffic counter will reset if the device is r...

104 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application ...

105 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Routing This page will display your current routing table. GO-RT-AC750

106 D-Link GO-RT-AC750 User Manual Section 3 - Configuration The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients. Wireless GO-RT-AC750

108 D-Link GO-RT-AC750 User Manual Section 3 - Configuration Support GO-RT-AC750

109 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network Connect a Wireless Client to your Router WPS Button Step 2 - Within 2 minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS process). The easiest and most secure way to c...

110 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network Windows® 8 WPA/WPA2 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know...

111 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network You will then be prompted to enter the network security key (Wi-Fi password) for the wireless network. Enter the password into the box and click Next . If you wish to use Wi-Fi Protected Setup (WPS) to connect to the rou...

112 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network Windows® 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the secu...

113 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network 3. Highlight the wireless connection with Wi-Fi name (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless...

114 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network 5. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect . You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless ...

115 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network WPS The WPS feature of the GO-RT-AC750 can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature: 1. Click the Start button and select Computer from the Start menu. ...

116 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network 3. Double-click the GO-RT-AC750. 4. Input the WPS PIN number (on the router label or in the Setup > Wireless Setup menu in the Router’s Web UI) and click Next .

118 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network 7. The following window appears while the router is being configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the router has been setup successfully. Make a note of the sec...

119 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless netwo...

120 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network WPA/WPA2 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the securi...

121 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network 3. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect . It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the secur...

123 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility, please refer to the u...

124 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used. 2. Highlight the Wi-...

125 D-Link GO-RT-AC750 User Manual Section 4 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK Wi-Fi password and click Connect . It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-P...

126 D-Link GO-RT-AC750 User Manual Section 5 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the GO-RT-AC750. Read the following descriptions if you are having problems. The examples below are illustrated in Window...

128 D-Link GO-RT-AC750 User Manual Section 5 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we sugg...

129 D-Link GO-RT-AC750 User Manual Section 5 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say...

130 D-Link GO-RT-AC750 User Manual Appendix A - Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D...

131 D-Link GO-RT-AC750 User Manual Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in you...

132 D-Link GO-RT-AC750 User Manual Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are bot...

133 D-Link GO-RT-AC750 User Manual Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract...

134 D-Link GO-RT-AC750 User Manual Appendix A - Wireless Basics Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it u...

135 D-Link GO-RT-AC750 User Manual Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP addres...

136 D-Link GO-RT-AC750 User Manual Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 - Click on Start > Control Panel > Network and Inter...

137 D-Link GO-RT-AC750 User Manual Appendix C - Technical Specifications Technical Specifications Hardware Specifications • LAN Interface: Four 10/100 Mbps LAN ports • WAN Interface: One 10/100 Mbps Internet port • Wireless Interface (2.4 GHz): IEEE 802.11b/g/n • Wireless Interface (5 GHz): IEEE 802...