D-Link Gigabit Switch - Manuals

VLAN (Virtual Local Area Network) A VLAN is a group of end-stations that are not constrained by their physical location and can communicate as if a common broadcast domain, a LAN. The primary utility of using VLAN is to reduce latency and the need for routers, by using faster switching instead. Othe...

Features ‹ 48×10/100Mbps Auto-negotiation Fast Ethernet RJ-45 ports ‹ 2×10/100/1000Mbps Auto-negotiation Gigabit RJ-45 ports ‹ 2×mini-GBIC/SFP ports, share with the 2 gigabit copper ports ‹ All RJ-45 ports support auto MDI/MDIX, so there is no need to use cross-over cables or an up-link port ‹ Half-...

UNPACKING AND INSTALLATION This chapter provides unpacking and installation information for the Switch. Unpacking Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items: ‹ One Web Smart 48+2G-Port 10/100/1000Mbps/SFP Switch ‹ One AC ...

AC Power The Switch uses a 100-240V AC, 50-60 Hz AC power supply. The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. The Switch’s power supply will adjust to the local power source automatically and may be turned on without having any or all LA...

IDENTIFYING EXTERNAL COMPONENTS This chapter describes the front panel, rear panel, and LED indicators of the Switch. Front Panel The figure below shows the front panels of the Switch. Figure 3. Front panel of 48+2G-port Gigabit Ethernet Switch LED Indicator: Comprehensive LED indicators display the...

UNDERSTANDING LED INDICATORS The front panel LEDs provide instant status feedback, and help monitor and troubleshoot when needed. Figure 5. LED indicators of the Switch Power and System LEDs POWER: Power Indicator On : When the Power LED lights on, the Switch is receiving power. Off : When the Power...

CONFIGURATION Through the Web Browser you can configure Switch settings such as VLAN, Trunking, QoS… etc. With the attached Web Management Utility, you can easily discover all Web Management Switches, assign the IP Address, change the password, and upgrade new firmware. Installing the Web Management...

z Trap IP: Shows the IP where the Trap is to be sent. z Subnet Mask: Shows the Subnet Mask set of the device. z Gateway: Shows the Gateway set of the device. Monitor List All the Web Smart Devices in the Monitor List can be monitored; you can also receive traps and show the status of the device. Sys...

The factory default password is "admin." Figure 9. Configuration Setting Password Change: You can use this Password Change when you need to change the password, fill in the required passwords in the dialog box and press the “Set” button to process the password change immediately. Figure 10. ...

In the “Option TAB”, there is the Refresh Time function; this function helps you to refresh the time for monitoring the device. Choose 15 secs, 30 secs, 1 min, 2 min, and 5 min to select the time for monitoring. In the “Help TAB”, there is About function, it will show out the version of the Web Mana...

Figure 14. Device Status Setup Menu When the main page appears, find the Setup menu on the left side of the screen (Figure 15). Click on the setup item that you want to configure. There are eleven options: Port Settings, VLAN Settings, Trunk Setting, Device Status, Statistic, System Settings, Trap S...

Figure 16. Port Configuration To change the port setting, click on the ID parameter to enter the selected port to configure its Speed/Disable, Flow control, and QoS setting. Figure 17. Speed: This setting has six modes—1000M Full, 100M Full, 100M Half, 10M Full, 10M Half, Auto, and Disable—for speed...

VID group and press the “Remove the VID” button. To modify the VID group setting, select the VID group and change the setting, and press the “Apply” button to save the settings. Figure 18. When you select Port VLAN setting, fill in each port’s PVID value between 1 and 4094. Figure 19. Trunk Setting ...

Figure 1. Mirror setting Be sure that the selected trunk setting port connects to the device with a same VLAN group. Device Status Click on the “Status” button to present the device status on this screen, it will show the System Status, Port Status, VLAN Status, and Trunk Status. Press “Refresh” whe...

System Setting The System Setting includes the System name, Location name, Login Timeout, IP Address, Subnet Mask, and Gateway. Through the Web Management Utility, you can easily recognize the device by using the System Name and the Location Name. The Login Timeout is used to set the idle time-out f...

To restore a current setting file to the device, you must specify the backup file and press the “Restore” button to process the setting of the recorded file. Figure 28. Backup Setting Note: When restoring a recorded file, the current password will not be erased. Reset Setting The Factory Reset butto...

TECHNICAL SPECIFICATIONS General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3z 1000BASE-SX/LX Gigabit Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3x Full Duplex Flow Control Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half-duplex), 2...

Product Registration Register online your D-Link product at http://support.dlink.com/register/ Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.

International Offices U.S.A 17595 Mt. Herrmann Street Fountain Valley, CA 92708 TEL: 1-800-326-1688 URL: www.dlink.com Canada 2180 Winston Park Drive Oakville, Ontario, L6H 5W1 Canada TEL: 1-905-8295033 FAX: 1-905-8295223 URL: www.dlink.ca Europe (U. K.) 4 th Floor, Merit House Edgware Road, Colinda...