D-Link DI-707PD - Manuals

5 Connections Pressing the Reset Button restores therouter to itsoriginal factorydefault settings. Features & Benefits Receptorfor the P o w e rA d a p t e r LAN ports provide connections to Ethernet-enabled devices. All LAN ports auto-sense cablet y p e s t o a c c o m o d a t e s t r a i g h t...

6 Features & Benefits continued Access Control supported Allows you to assign different access rights for different users Packet filter supported Packet Filter allows you to control access to a network by analyzing the incoming and outgoing packets and letting them pass or halting them based on ...

7 Introduction to Firewalls A firewall is a device that sits between your computer and the Internet that prevents unauthorized access to or from your network. A firewall can be a computer using firewall software or a special piece of hardware built specifically to act as a firewall. In most circumst...

8 Introduction to Virtual Private Networking Virtual Private Networking (VPN) uses a publicly wired network (the Internet) to se- curely connect two different networks as if they were the same network. For example, an employee can access the corporate network from home using VPN, allowing the employ...

9 LEDS LED stands for L ight- E mitting D iode. The DI-707P has the following LEDs as described below: LED LED Activity Power A steady light indicatesa connection to a power source a power source M1 LED M2 LED Lights up when the device has an Internetconnection WAN A solid light indicates connection...

10 For a typical network setup at home (as shown above), please do thefollowing: 2 1 3 4 5 6 Getting Started Please refer to the following sections of this manual for additional information about setting up a network: Networking Basics - learn how to check and assign your IP Address; share printers ...

11 Using the Configuration Menu Whenever you want to configure your network or the DI-707P, you can access the Configuration Menu by opening the web-browser and typing in the IP Address of theDI-707P. The DI-707P default IP Address is shown below: Open the web browser Type in the IP Address of the D...

12 Using the Configuration Menu Home > WAN Choose WAN Type WAN stands for Wide Area Network . In this case WAN represents the mode in which you connect to the Internet. If you are uncertain, please ask your ISP which of thefollowing represents your connection mode to the Internet: Static IP Addre...

13 Using the Configuration Menu Home > WAN > Dynamic IP Address Most Cable modem users will select this option to obtain an IP Address automatically from their ISP (Internet Service Provider). Host Name- This is optional, but may be required by some ISPs. The host name is the device name of th...

14 Using the Configuration Menu Home > WAN > Static IP Address If you use a Static IP Address, you will input information here that your ISP has provided to you. Secondary DNS- (Optional) Input the Secondary DNS address provided by your ISP. Primary DNS- Input the primary DNS address provided ...

15 Using the Configuration Menu Home > WAN > PPPoE Most DSL users will select this option to obtain an IP address automatically from their ISP through the use of PPPoE. MTU- Maximum Transmission Unit ; default is 1492; you may need to change the MTU to conform to your ISP. Assigned IP Address-...

17 Using the Configuration Menu Home > WAN > BigPond Cable Account- Enter in the username for the BigPond account Password- Enter the password for the BigPond account Login Server- (Optional) enter the Login Server name if required Renew IP forever- If enabled, the device will automatically co...

18 Home > LAN Using the Configuration Menu LAN is short for Local Area Network. This is considered your inter- nal network. These are the IP settings of the LAN interface for the DI-707P. These settings may be re- ferred to as Private s e t t i n g s . Yo u m a y change the LAN IP address if need...

19 Advanced > Virtual Server Using the Configuration Menu The DI-707P can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DI-707P firewall feature f...

20 Using the Configuration Menu Advanced > Application Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes som...

21 Using the Configuration Menu Advanced > MAC Filters MAC (Media Access Control) Filters are used to deny or allow LAN (Local Area Network) computers from accessing the Internet and network by their MAC address. At the bottom of the screen, there is a list of MAC addresses from the DHCP client c...

22 Using the Configuration Menu Advanced >IP Filter Disabled IP Filter- Select this option if you do not want to use IP filters. Allow all computersto access the Internetexcept those listedbelow- Those in the list will be denied access to the Internet; all other computers will be allowed access t...

23 Using the Configuration Menu Advanced > Domain Filter Use Domain filters to allow or deny computers access to specific Internet domainswhether it is through www, ftp, snmp, etc. Domain filters apply both to wired computersconnected to one of the four Ethernet LAN ports and also to wireless cli...

24 Using the Configuration Menu Advanced > SNMP Enable SNMP- Get Community- (Simple Network Management Protocol) Enter the password public in this field to allow “Read only” access to network administration using SNMP. You can view the network, but no configuration is possible wth this setting. S...

25 Using the Configuration Menu Advanced > DDNS DDNS (Dynamic Domain Name System) keeps dynamic IP addresses (e.g., IPaddresses assigned by a DHCP capable router or server) linked to a domain name.Users who have a Dynamic DNS account may use this feature on the DI-707P. DDNS- When an IP address i...

27 Using the Configuration Menu Advanced > Routing Static routes can be added if you require specific routes within your internal network.These routes will not apply to the WAN (Internet) network. Destination- Enter in the IP of the specified network that you want toaccess using the static route ...

28 Using the Configuration Menu Tools> Admin Password- Remote Management- To change the admin password, enter in the old password, and enter the new password twice to confirm You can change the admin password here. It is recommended that you change theadmin password from the default setting. The ...

29 Using the Configuration Menu Tools> Time Enable NTP- Sync- Select to enable NTP and synchronize the time settings on your network using an NTP server Set the time here by entering it manually or use NTP (Network Time Protocol.) NTP is standard protocol on the Internet that sychronizes the time...

30 Using the Configuration Menu Tools > System Click Save to save the current settings to the local Hard Drive Click Browse to find the settings file, then click Load Save Settings toLocal Hard Drive- Load Settings fromLocal Hard Drive- Restore to FactoryDefault Settings- Click Restore to restore...

31 Using the Configuration Menu Tools > Firmware Browse- After you have downloaded the new firmware, click Browse in this window to locate the firmware update on your hard drive. Click Apply to complete the firmware upgrade. Note! Do not power off the unit when it is being upgraded. When theupgra...

32 Using the Configuration Menu Tools > Misc Block WAN Ping- Click Enable to block the WAN ping. Computers on the Internet will not get a reply back from the DI-707P when it is being “ping”ed. This may help to increase security. Restart Device- Click reboot to restart the unit. Non-standard FTP p...

33 Using the Configuration Menu Status > Device Info This screen displays information about the DI-707P. Refresh- Click Refresh to update the current information.

34 Using the Configuration Menu Status > Log This screen displays activities occurring on the DI-707P. Log Settings- Click for advanced features (see next page.) Back- Click Back to return to the top of the log. Refresh- Click Refresh to update the log.

35 Using the Configuration Menu Status > Log Settings Send E-Mail alert to- Enter in the email address of the recipient who will receive the email log. Enter in the IP address of a syslog server within the network. Click Enable to activate the policy. The DI-707P will send all of it’s logs to the...

36 Using the Configuration Menu Help This screen displays the complete Help menu. For help at anytime, click the Help tab in the Configuration menu.

37 Insert the installation CD-ROM into the CD-ROM drive. The following window will beshown automatically. If it is not, please run “install.exe” on the CD-ROM. Installing the Print Server Software Click Install Print Server Software Click Next Select the Operating System

38 Select the destination folder. Click Next After rebooting your computer, the software installation procedure is finished. Installing the Print Server Software (continued) Click OK Click Finish Click Browse to select a destinationfolder Select the option for restarting thecomputer.

39 Configuring on Windows 98SE/ME Platforms After you finish the software installationprocedure, your computer will be capable ofnetwork printing provided by the DI-707P. Forconvenience, we call the printer connected tothe printer port of the DI-707P a print server . On a Windows 95/98 platform, ope...

40 Configuring on Windows XP/2000/NT Platforms The configuration procedure for aWindows 2000/XP platform is similar tothat of Windows 95/98 except thescreen of printer Properties : (Note: Screen shots are taken in Windows 2000, similarscreens will appear in Windows XP.) Click Port Click Configure Po...

41 Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work,using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers ...

42 Please follow all the instructions in this window: Networking Basics Click Next In the following window, select the best description of your computer. If yourcomputer connects to the internet through a gateway/router, select thesecond option as shown. Click Next

44 Please wait while the Network Setup Wizard applies the changes. Networking Basics When the changes are complete, click Next . Please wait while the Network Setup Wizard configures the computer. This may take a few minutes.

45 Networking Basics In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next . Insert a disk into the Floppy Disk Drive, in this case drive A.

46 Networking Basics Please read the information under Here’s how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click Next.

47 Networking Basics Please read the information on this screen, then click Finish to complete the Network Setup Wizard . The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the N...

48 Networking Basics Naming your Computer To name your computer, please follow these directions:In Windows XP : Click Start (in the lower left corner of the screen) Right-click on My Computer Select Properties and click Select the Computer Name Tab in the System Properties window. You may enter a Co...

49 Networking Basics Naming your Computer In this window, enter the Computer name Select Workgroup and enter the name of the Workgroup All computers on your network must have the same Workgroup name. Click OK Checking the IP Address in Windows XP The wireless adapter-equipped computers in your netwo...

50 Networking Basics Checking the IP Address in Windows XP This window will appear. Click the Support tab Click Close Assigning a Static IP Address in Windows XP/2000 Note: Residential Gateways/Broadband Routers will automatically assign IP Ad- dresses to the computers on the network, using DHCP (Dy...

51 Networking Basics Assigning a Static IP Address in Windows XP/2000 Double-click on Network Connections Double-click on Properties Right-click on Local Area Connections

52 Networking Basics Assigning a Static IP Address in Windows XP/2000 In the window below, input your IP address, subnet mask, defaultgateway and DNS server address. (The IP Addresses on your networkmust be within the same range. Forexample, if one computer has an IPAddress of 192.168.0.2, the other...

53 Networking Basics Assigning a Static IP Address with Macintosh OSX Go to the Apple Menu and se- lect System Preferences c Click on Network Select Built-in Ethernet in the Show pull-down menu Select Manually in the Con- figure pull-down menu Input the Static IP Address , the Subnet Mask and the Ro...

54 Networking Basics Selecting a Dynamic IP Address with Macintosh OSX Go to the Apple Menu and select System Preferences Click on Network Select Built-in Ethernet in the Show pull-down menu Select Using DHCP in the Configure pull-down menu Click Apply Now The IP Address, Subnet mask , and the Route...

55 Networking Basics Adding and Sharing Printers in Windows XP After you have run the Network Setup Wizard on all the computers in your network (please see the Network Setup Wizard section at the beginning of Networking Basics ,) you can use the Add Printer Wizard to add or share a printer on your n...

56 Networking Basics Adding a local printer (a printer connected directly to a computer) A printer that is not shared on the network and is connected directly to one computer is called a local printer . If you do not need to share your printer on a network, follow these directions to add the printer...

57 Networking Basics Adding a local printer Click Next Select Local printer attached to thiscomputer (Deselect Automati- cally detect and installmy Plug and Playprinter if it has been selected.) Click Next Select Use the follow- ing port: From the pull-down menu select the correct port for your prin...

58 Networking Basics Adding a local printer Select and highlight the correct driver for your printer. Click Next (If the correct driver is not displayed, insert the CD or floppy disk that came with your printerand click Have Disk .) At this screen, you can change the nameof the printer (optional.) C...

59 Networking Basics Adding a local printer This screen gives you information about your printer. Click Finish When the test page has printed, Click OK

61 Networking Basics Sharing a network printer Click on Add a printer Click Next Select Network Printer Click Next

64 Networking Basics Sharing an LPR printer To share an LPR printer (using a print server,) you will need a Print Server such as the DP-101P+ . Please make sure that you have run the Network Setup Wizard on all the computers on your network. To share an LPR printer , please follow these directions: ...

68 Networking Basics Sharing an LPR printer Note: You must run the Network Setup Wizard on all the computers on your network before you run the Add Printer Wizard . Please run the Add Printer Wizard on all the computers on your network in order toshare the printer. Click Finish to complete the addit...

69 After you have tried other methods for troubleshooting your network, youmay choose to Reset the DI-707P to the factory default settings. To hard-reset the D-Link DI-707P to the Factory Default Settings, please dothe following: Resetting the DI-707P to the Factory Default Settings Use a paper clip...

70 Technical Specifications VPN Pass Through Function PPTPL2TPIPSec Device Management Standards IEEE 802.3 10BASET-T Ethernet IEEE 802.3x Flow Control IEEE 802.3u 100BASE-TX Fast Ethernet I EEE 802.1p Priority Queue ANSI/IEEE 802.3 NWay auto-negotiation Web-Based – Internet Explorer 6x or later; Net...

71 You can find the most recent software and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States for theduration of the warranty period on this product. U.S. customers can contact D-Link technical support through our web site,or by ...

72 Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited warranty for its product only to the person or entity that originally purchased the product from: D-Link or its authorized reseller or distributor andProducts purchased and delivered within...