D-Link DI-1162 - Manuals

DI-1162 Remote Access Router vi Step 2 - Connecting the Console to the Router .............................14Step 3 - Initial Configuration of the Router ..................................15Step 3a - Configuring the LAN Port ..............................................17Step 3b - Configuring the W...

DI-1162 Remote Access Router vii PPP Configuration ........................................................................95 A DMIN [ ISTRATION ] C ONFIGURATION ................................................99 S YSTEM M AINTENANCE .....................................................................

DI-1162 Remote Access Router viii APPENDIX B – SPECIFICATIONS .............................................139 APPENDIX C - IP CONCEPTS .....................................................141 IP A DDRESSES ................................................................................141 IP Networ...

DI-1162 Remote Access Router Introduction 1 Introduction Congratulations on your purchase of a D-Link DI-1162 Remote AccessRouter. Your new router offers inexpensive yet completetelecommunications and internetworking solutions for your corporateoffice, school or business. It is ideal for everything ...

DI-1162 Remote Access Router 2 Networking Compatibility The DI-1162 is compatible with remote access products from othercompanies such as Ascend, Cisco, and 3Com. Furthermore, it supportsMicrosoft Windows 95, Windows 98, and Windows NT remote accesscapability. Product Features LAN Port The DI-1162 i...

DI-1162 Remote Access Router Introduction 3 These modules allow you to expand the functionality of the DI-1162 tofulfill all your internetworking needs. Dial on Demand The Dial-On-Demand feature allows the DI-1162 to automaticallyplace a call to a remote node, via a WAN, whenever there is trafficcom...

DI-1162 Remote Access Router 4 assigning and managing IP addresses for each individual machine onthe LAN. Data Compression The DI-1162 incorporates the hardware-based Stac LZS DataCompression for CCP (Compression Control Protocol). Network Address Translation (NAT/NAPT) This feature allows multiple ...

DI-1162 Remote Access Router Introduction 5 Link Branch Offices The DI-1162 routes communications through its two (upgradeable tofour) WAN ports allowing direct communications to a branch office viaphone lines, the internet or both. Local Routing The DI-1162 can route traffic between up to eight loc...

DI-1162 Remote Access Router 6 ♦ At least one modem or CSU/DSU for connecting the WANport(s) to a telephone line. ♦ At least one Internet IP Address per port on the router. ♦ An Internet Service Provider (ISP).

DI-1162 Remote Access Router Installation 7 Installation This chapter details installation procedures for the DI-1162 router. Overview The DI-1162 can be configured in two ways; through a direct serialconnection (a console), or remotely, through the included RouterConfiguration Utility, Telnet, etc....

DI-1162 Remote Access Router 8 Installation Other Resources For more information about your DI-1162 check the following sources: ♦ Quick Installation Guide. ♦ Support disk containing RouteView , a Windows-based configuration program used to set up and configure the router. ♦ Frequently Asked Questio...

DI-1162 Remote Access Router Installation 9 Identifying External Components The following section illustrates the different components on therouter’s front and rear panels. Before using the router it is highlyrecommended to familiarize yourself with these components to ensureeffective use of the dev...

DI-1162 Remote Access Router 10 Installation LED STATUS/ FUNCTION Power Lights whenever the router is plugged in, turned on, and thusreceiving power. Diag Lights during the startup POST test. Boot Lights briefly during startup after the PROM program hasexecuted. Indicates a successful boot up. Run S...

DI-1162 Remote Access Router Installation 11 • Diagnostics RS-232 Serial Port A DB-9 female connector used to connect a console to the routerfor initial setup and out-of-band management. • Wan Ports (1 and 2) Two DB-25 male connectors each of which can be connected to adial-up (dial in or out) line ...

DI-1162 Remote Access Router 12 Installation If it is connected to another NWay capable port, the two ports willconfigure themselves to attain the best connection possible. • Fan Provides ventilation inside the router. Please ensure to leaveadequate space at the rear and sides of the unit for proper...

DI-1162 Remote Access Router Installation 13 ♦ Install the router in a site free from strong electromagnetic fieldgenerators (such as motors), vibration, dust, and direct exposureto sunlight. ♦ When installing the router on a level surface, attach the rubberfeet to the bottom of the device. The rubb...

DI-1162 Remote Access Router 14 Installation Before connecting or disconnecting an RS-232 cable between theDI-1162 and the console and modems, please make sure all devices areoff to avoid any chance of damage. Step 1 - Setting up the Console The initial setup of the DI-1162, requires connecting a co...

DI-1162 Remote Access Router Installation 15 Using the Console The Console Program is the interface that you will be using to configure your DI-1162. Several operations that you should be familiarwith before you attempt to modify the configuration of your router arelisted below: ♦ Moving Forward to ...

DI-1162 Remote Access Router 16 Installation To log on to the router, use the factory set username and password‘Admin’ (without the quotes). Please note that the user name andpassword are case-sensitive. Upon entering the username and password (using the < tab > key to jump to the next field),...

DI-1162 Remote Access Router Installation 17 Step 3a - Configuring the LAN Port Preparing the router for connection to a LAN only requires enablingthe LAN port, enabling IP networking and assigning the LAN port anIP address. After the LAN port is configured, all other features on therouter can be co...

DI-1162 Remote Access Router 18 Installation ♦ Choose Exit in the sub-menus to return to the Main Menu. 2. Enable IP Networking ♦ Choose Network Configuration, IP Configuration. ♦ Position the cursor over the last item IP Networking and press <space bar> to Enable it . ♦ Position the cursor on...

DI-1162 Remote Access Router Installation 19 If you have any questions regarding the settings you made or othersettings in the submenus, please refer to the next chapter Configuration and Management . At this point, please proceed to the next initial configuration step. Step 3b - Configuring the WAN...

DI-1162 Remote Access Router 20 Installation • SLIP – asynchronous mode used for modems. • Async PPP - asynchronous mode used for modems. • HDLC – synchronous mode used for CSU/DSU’s or synchronous modemsusing a leased line. • Sync PPP - synchronous mode used for CSU/DSU’s or synchronous modemsusing...

DI-1162 Remote Access Router 22 Installation ♦ Choose WAN1 ♦ Please refer to the Configuration and Management section of this manual for more detailed information regarding the itemsin this screen. ♦ Position the cursor on the Save option at the bottom of the screen and press <Enter> to save t...

DI-1162 Remote Access Router Installation 23 ♦ From the Main Menu choose Advanced Functions , Remote Access Configuration, Remote Network Profile and press <Enter> in the first empty field. ♦ Set the Direction to IN, OUT or BOTH. ♦ Enter a Name and Password used to establish Incoming and/or Ou...

DI-1162 Remote Access Router 24 Installation Your WAN ports are now configured and should operate normally.Please note that many of the settings configured here depend on thetype and capabilities of the device being connected. At this point in the installation process, you need to turn off the route...

DI-1162 Remote Access Router Installation 25 Make sure both the WAN device(s) and the router are turned OFFwhen making these connections. Step 6 – Plugging in All Devices Plug the 100~240V AC/DC power cord into the power jack on therouter’s rear panel and into a power strip or grounded wall outlet. ...

DI-1162 Remote Access Router Configuration and Management 27 Configuration and Management After the initial startup (POST) test, the router will prompt you forlogin and password. This is the opening page of the router’sconfiguration program, called the Console program. The Consoleprogram is stored i...

DI-1162 Remote Access Router 28 Configuration and Management be used to initially configure the relevant port on the router. Please see Step 3 - Initial Configuration of the Router on page 15 of this manual for more detailed information. Console Program Main Menu The Main Menu is shown below. As men...

DI-1162 Remote Access Router 30 Configuration and Management • External MAC Address – the physical address of the external LAN add-in module, if present. Interface Configuration Under Interface Configuration in the main menu is the following interface configuration screen, used to configure the inte...

DI-1162 Remote Access Router Configuration and Management 31 LAN Sub-menu The parameters are described below: • Description – this is a user-defined, 32-character identifier used to name the LAN. • Operation Mode – The LAN port is automatically set to Auto- Negotiation (NWay). When connected to anot...

DI-1162 Remote Access Router 32 Configuration and Management WAN Sub-menu The parameters are described below: • Description – this is a user-defined, 32-character identifier used to name the WAN. • Modem Init String – this parameter is valid only for asynchronous connections. It is a user input AT c...

DI-1162 Remote Access Router Configuration and Management 33 X1 – displays the established connection speed to the dial-in user (e.g. Connection established at 56.6 kps ). • Protocol – this is a protocol used to encapsulate IP messages over synchronous and asynchronous serial links. The device being...

DI-1162 Remote Access Router 34 Configuration and Management setting may be used when you do not wish dial-in users ornetworks to identify themselves or be subject to security. • Baud Rate – this parameter must be set to configure the communication speed for asynchronous communication devices(modems...

DI-1162 Remote Access Router Configuration and Management 35 Network Configuration IP protocol configuration and static routes are configured in theNetwork Configuration sub-menu. This menu is shown below: IP Stack Configuration The network interface IP address, mask and protocols are specified inth...

DI-1162 Remote Access Router 36 Configuration and Management The parameters are described below: • IP Address – this is the IP address for the router on the network to which this interface is connected. • Netmask – this is a 32-bit bit mask that shows how the IP address is to be divided into network...

DI-1162 Remote Access Router Configuration and Management 37 The mask should contain at least the standard network portion (asdetermined by the address's class), and the subnet field should becontiguous with the network portion. • Forwarding (LAN) – this enables or disables communications between th...

DI-1162 Remote Access Router 38 Configuration and Management 3. Talk – the router will send adjacent routers it’s own routing table, but will not incorporate routing information from them. 4. Both – the router will incorporate routing information from adjacent routers, and will send adjacent routers...

DI-1162 Remote Access Router Configuration and Management 39 LAN) where you wish the router to work with a device on thenetwork that must act as a DHCP server. Otherwise, this featureshould be kept disabled. • RIP Spoofing (WAN) – this feature should only be enabled if you have more than one router ...

DI-1162 Remote Access Router 40 Configuration and Management The parameters are described below: • IP Address – this specifies the destination network IP address (or a host, depending on the netmask) and pairs it with a gateway. • Netmask – this mask shows how the destination IP address is to be div...

DI-1162 Remote Access Router Configuration and Management 41 IP Static Route Examples The IP Static Route Table shown in the example IP Static Route screenabove has the first three entries configured for commonimplementations of static routing. The first entry assumes that WAN1 has a connection to t...

DI-1162 Remote Access Router 42 Configuration and Management Router Advertisement When this option is enabled, the router will periodically send out ICMPpackets that announce itself on the network. These ICMP packets areutilized by the Windows 98 or later operating system, which willautomatically up...

DI-1162 Remote Access Router Configuration and Management 43 SNMP Agent Configuration The Simple Network Management Protocol (SNMP), defined in STD15, RFC 1157, is a protocol governing the management and themonitoring of IP network devices and their functions. The DI-1162supports the use of SNMP to ...

DI-1162 Remote Access Router 44 Configuration and Management The parameters are described below: • SNMP Community String – this community string is a user- defined identifying name used to group together some arbitrary setof SNMP application entities managed by the network manager. • Access Right – ...

DI-1162 Remote Access Router 46 Configuration and Management SNMP Authenticated Trap Returning to the SNMP Agent Configuration menu, you can ‘Enable’ or ‘Disable’ an authentication failure trap message being sent to the Management Station by the router. When an SNMP packet with aninvalid community n...

DI-1162 Remote Access Router Configuration and Management 47 Advanced Functions The Advanced Functions menu holds most of the more complexconfiguration settings and is shown below: Remote Access Configuration The Remote Access Configuration menu is used to set up the router fordial-in and dial-out c...

DI-1162 Remote Access Router Configuration and Management 49 device is a router). In almost all cases, a Remote Network Profile needsto be set up for each network that will connect to the DI-1162 via aWAN connection. The Remote Network Profiles are necessary for therouter to identify and tailor the ...

DI-1162 Remote Access Router Configuration and Management 51 The Remote Access Configuration submenu is shown below. All itemsin the submenu are described as follows. Dial Configuration You can configure the two WAN interfaces on your DI-1162 todial-out only when a packet is forwarded to that interf...

DI-1162 Remote Access Router 52 Configuration and Management Dial In IP Pool The dial in IP pool allows you to define a range of IP addressesthat will be reserved for and assigned to dial-in users. The items are described as follows: ♦ IP Address – is the first IP Address that will be assigned to a ...

DI-1162 Remote Access Router Configuration and Management 53 Range – is the number of IP Addresses that can be assigned. In the window shown above, dial-in users will be assigned the IPAddresses 170.100.200.1 or 170.100.200.2 (only two arenecessary since the router used in the examples has only two ...

DI-1162 Remote Access Router 54 Configuration and Management will search for a Remote Network Profile that further configures this WAN port for dialing-out. Set Peer IP as Default Gateway – when enabled, this feature sets the IP address of the remote device as the default gateway (defaultnext hop ro...

DI-1162 Remote Access Router Configuration and Management 55 The parameters in the above window are described as follows: • Name – the maximum length is 64 characters. This username is for password challenges (authentication). The user dialing in mustsupply this username in order to be allowed acces...

DI-1162 Remote Access Router 56 Configuration and Management Dynamic - taken from the Dial In IP pool , or None - the remote user supplies his own IP Address. State – enables/disables this User Profile. Remote Network Profile The Remote Network Profile is used to configure the router forWAN connecti...

DI-1162 Remote Access Router Configuration and Management 59 Script File Configuration Script files are used on dial-out connections where the server you areconnecting to uses a script for the logon procedure (common with manyISP’s). If you would like the router to automatically logon to a remoteser...

DI-1162 Remote Access Router 60 Configuration and Management Commands Script files can perform six Commands. You can choose theappropriate command by positioning the cursor in the Command fieldand pressing <space bar> to toggle to the appropriate command. Thescript commands are defined as foll...

DI-1162 Remote Access Router Configuration and Management 61 • ^M – <Enter> or <Return>. ♦ Delay – will delay for the number of seconds defined in the Parameter field. ♦ Get My IP – Will get the IP address from the ISP if the ISP sends it. This command is only valid for SLIP connections....

DI-1162 Remote Access Router 62 Configuration and Management DHCP Server Configuration When acting as a DHCP server, the DI-1162 will manage many of theIP network parameters. The DI-1162 will never assign a broadcast ornetwork IP addresses to hosts, even if such an address is included in thespecifie...

DI-1162 Remote Access Router 64 Configuration and Management • DNS IP – this specifies the Domain Name System server, used by the DHCP clients using leased IP addresses, to translate hostnamesinto IP addresses or vice-versa. • WINS IP – this specifies the IP address of the Windows Internet Naming Se...

DI-1162 Remote Access Router Configuration and Management 65 The parameters are described below: • IP Address – this is the static IP address to be assigned. • MAC Address – this specifies the physical address of the particular host that will receive the above IP address. All other parameters ( Netm...

DI-1162 Remote Access Router 66 Configuration and Management • Time Threshold – this specifies the maximum amount of time (in seconds) since the host began requesting an IP address. If the valuedefine here is exceeded, the relay agent will not pass along therequest from the host. • State – enables/d...

DI-1162 Remote Access Router Configuration and Management 67 The three sub-menus are described: 1. Filter State of Interface – this is used to choose the default, routing decisions for packets, not meeting the criteria for specificfilters. 2. Layer 2 Filter – this is a data-link layer (protocol inde...

DI-1162 Remote Access Router 68 Configuration and Management that was applied to a specific interface, will be subjected to this default,routing decision. Each decision on handling packets is described below: 1. Disable – this does not apply a default, routing decision. 2. Forward – this allows the ...

DI-1162 Remote Access Router Configuration and Management 69 The parameters of a filter are described below: • Name – this is a 12 character (maximum), alphanumeric, user- defined name, used to identify the filter. • Direction – this defines the direction of the frame relative to the Interface param...

DI-1162 Remote Access Router 70 Configuration and Management after the preamble. The range of the Offset parameter is from 0 to255 octets. The first byte in a packet has an offset 0. • Length – this is the number of bytes (octets) from the offset value (the Offset reference byte). • Value – this is ...

DI-1162 Remote Access Router 72 Configuration and Management • Dst IP – this is the destination address in the IP header of the packet. • Dst Netmask – this mask is bit-wise AND’d with the destination IP address, and compared to the IP address of the outgoinginterfaces. • Dst Port – this is the dest...

DI-1162 Remote Access Router Configuration and Management 73 Multiple Home can be demonstrated by this example: A company has 625 users (computers) all connected to one physicalnetwork using Ethernet. However, the company only has one Class CIP network address, 202.100.160.0. This network address wi...

DI-1162 Remote Access Router 74 Configuration and Management The parameters are described below: • IP Address – this is a network IP address, access point, to a separate, physical network, on the LAN. • Routing Protocol – this is the same as in the Network Configuration section. Keep in mind that th...

DI-1162 Remote Access Router Configuration and Management 75 Basically, when a packet comes into the router from a WAN port and isdestined for a host on the LAN, the router will use information definedhere to immediately send the packet to the host rather than send out anARP request to find the host...

DI-1162 Remote Access Router 76 Configuration and Management NAT has two major benefits. First, NAT allows many users to accessthe Internet using a small number or even a single global IP address.This can greatly reduce the costs associated with Internet access andalso helps alleviate the current sh...

DI-1162 Remote Access Router 80 Configuration and Management made. Since there are only 5 global IP addresses in the example above,there can only be 5 mappings at any one time. In other words, muchlike static NAT, only 5 local machines can access the Internet at anyone time. However, contrary to sta...

DI-1162 Remote Access Router Configuration and Management 81 Configure NAT/NAPT The first screen shows the complete NAT table that is defined by thenetwork manager: For any NAT entry, you must configure two different screens. The firstone is accessible by positioning the cursor over the name field a...

DI-1162 Remote Access Router 82 Configuration and Management you must save the changes, EXIT , and position the cursor over the NAT IP Pool to configure variables there. Name Field Configuration Screen The configuration screen for the name field appears as follows: The parameters are described as fo...

DI-1162 Remote Access Router Configuration and Management 83 Static NAT – Maps one global IP address to one local IP address. After all global IP addresses are assigned, they willremain static. This option may be necessary for email, web,ftp servers, etc. where static IP addresses are essential foro...

DI-1162 Remote Access Router 84 Configuration and Management Dynamic NAT This screen (below) is how the NAT IP Pool appears, if Dynamic NAT was chosen for the Translation Mode parameter. Each entry, in this configuration, can be used to map multiple, contiguous globaladdresses and local addresses to...

DI-1162 Remote Access Router Configuration and Management 85 • Range – this is the range of contiguous local addresses above (and including) the base Local IP . • State – this toggles the enable, disable, for this NAT entry. Dynamic NAPT This screen (below) is how the NAT IP Pool appears, if Dynamic...

DI-1162 Remote Access Router 86 Configuration and Management Static NAT This screen (below) is how the NAT IP Pool appears, if Static NAT was chosen for the Translation Mode parameter. Each entry in this configuration is used to map a single global IP address a single local IPaddress. The parameters...

DI-1162 Remote Access Router Configuration and Management 87 address and port. Notice that the global address will be the external IPaddress of the global interface. • Port – this is a destination port number, used by TCP and UDP, to de-multiplex the incoming IP packet. In the above example, incomin...

DI-1162 Remote Access Router Configuration and Management 89 The fields in the above window are described as follows: • Protocol – [UDP] or [TCP]. This field designates the type of packets that will be acted on. • Start Port – Some applications can only send data over a certain range of port numbers...

DI-1162 Remote Access Router 90 Configuration and Management In the example for the game Diablo shown in the above screen, if apacket is sent out on the TCP port number 6112 (a request by a localuser to a Diablo server on the Internet to join a group game), allincoming packets on the UDP port 6112 (...

DI-1162 Remote Access Router Configuration and Management 91 DNS Configuration The DI-1162 router has a built in recursive DNS server. The maximumamount of memory that will be used by the router’s Domain NameServer is 64Kb which averages out to be about 800 entries. In otherwords, up to 800 domain n...

DI-1162 Remote Access Router 92 Configuration and Management ♦ Lookup Host Table – enable/disables DNS to reference up to eight host names defined in the Host Table shown below. ♦ DNS Domain Name – the domain name suffix in which the router resides, to be appended to the host name defined in the hos...

DI-1162 Remote Access Router Configuration and Management 93 Items are described as follows: ♦ IP – The IP address for the host. ♦ Host Name – the name used by the host. ♦ State – Enables/disables entry. Radius Configuration Radius is a password protocol where passwords are stored on a Radiusserver....

DI-1162 Remote Access Router 94 Configuration and Management Items in the above submenu are described as follows: ♦ RADIUS State – enables/disables Radius. ♦ Type – refers to the type of external password protocol. Currently, only Radius is supported. ♦ Server IP Address – this is the IP Address of ...

DI-1162 Remote Access Router 96 Configuration and Management second WAN port to place a call and add bandwidth to the WANconnection when the BOD High Threshold is exceeded for the Add Bandwidth Delay period. Bandwidth can also be subtracted when WAN throughput falls below the BOD Low Threshold and S...

DI-1162 Remote Access Router 98 Configuration and Management RX ) ever exceeds 80% of the 64kps (51.2kps), the router will sample the line for an additional 5 seconds. If the traffic continuously exceeds 80% for the 5 second delay time, WAN 2 will dial up and add bandwidth to the connection. Assumin...

DI-1162 Remote Access Router Configuration and Management 99 Stac Compression – this is an industry standard 4:1compression scheme. When enabled, the router will try to use Stac compression onthe designated WAN port whenever possible. If the destination deviceis not capable of using Stac compression...

DI-1162 Remote Access Router 100 Configuration and Management Please note any changes made here as they are necessary for logginginto the console program. System Maintenance Your DI-1162 provides useful tools for maintaining your device.These tools include; updates on system status, upgrades to the ...

DI-1162 Remote Access Router Configuration and Management 103 System Status The System Status submenu displays key information about the router and appears as follows: Statistics Under the Statistics submenu, the routing table and routing statistics for each interface are displayed. Routing Table Th...

DI-1162 Remote Access Router Configuration and Management 105 Counter This feature displays some of the counters contained in MIBII and theproprietary MIB. The table is updated every 5 seconds, and the countertable can be reset by performing a system reset on the router. Note thatperforming a system...

DI-1162 Remote Access Router Configuration and Management 109 ! Rx CD Lost Packets – Carrier Detect Lost. This counts the number of Carrier Detect packets that were lost by the router. ! Rx Framing Error Packets – Packets with framing errors can occur on the WAN port only when using HDLC in sync mod...

DI-1162 Remote Access Router 110 Configuration and Management The parameters are described as follows: ♦ Code – A special code for categorizing events. Some codes include: • 0 Cold Start • 1 Link Change • 2 Tx Abort • 3 Rx Abort • 4 Connect/Disconnect • 5 NAT Request • 6 DHCP Request ♦ Port – The in...

DI-1162 Remote Access Router Configuration and Management 111 Trace Buffer This feature captures packets in a buffer to help D-Link technicalsupport personnel identify problems with your router. Trace Buffer Configuration Enables/disables the Trace buffer feature. View Trace Buffer Displays the head...

DI-1162 Remote Access Router 112 Configuration and Management Diagnostic This feature tests the connection between the router and connectedperipherals on a given interface. Connection Test This feature tests a dial-out WAN connection.

DI-1162 Remote Access Router Configuration and Management 113 ♦ Interface – The WAN interface to be tested. ♦ Phone Number – The phone number that will be dialed by the WAN Interface. Please ensure that a modem answers the phone onthe other end. ♦ Baud Rate – The rate of data transmission. The answe...

DI-1162 Remote Access Router 114 Configuration and Management Ping Test This test makes sure there is an IP network connection to a particularIP address. ♦ IP Address – This is the IP Address of the device that the router will attempt to reach. The router will check it routing table and tryto locate...

DI-1162 Remote Access Router Configuration and Management 115 System WAN Test The System WAN test is used to diagnose the WAN port. It can onlybe run if the WAN port is disabled in the Interface Configuration submenu.

DI-1162 Remote Access Router 116 Configuration and Management External Module Test This performs either a System LAN or System WAN test on theexternal module depending on which type of module is installed.

DI-1162 Remote Access Router Configuration and Management 117 Software Update New routing software can be downloaded from a TFTP server. If you do not have a TFTP server on your LAN, you can use theincluded Router Configuration Utility to upgrade the software. ThisWindows-based utility has a built-i...

DI-1162 Remote Access Router 118 Configuration and Management A system restart will not affect the router’s settings, but will clear alltables including the routing table and all SNMP counters and tables. Itis also used to initiate a software update. Factory Reset Performing a factory reset erases a...

DI-1162 Remote Access Router Configuration and Management 119 Items in the window are described below: • Remote IP Address – this is the IP address of the TFTP server on which you wish to store the settings file. • TFTP Time Interval – the time between requests to occupy TFTP server time. If the rou...

DI-1162 Remote Access Router PROM System Configuration 121 PROM System Configuration The PROM program is run before the normal console (runtime)configuration program in the router’s Flash Memory. Thus, the PROMSystem Configuration can be used if there are problems with therouter’s console program. S...

DI-1162 Remote Access Router 122 PROM System Configuration System Configuration The parameters are described as follows: ! Hardware Revision – this is the version ID of hardware used in this router. ! Boot PROM Firmware Version – this is the version ID of firmware used in this router. ! MAC Address ...

DI-1162 Remote Access Router PROM System Configuration 123 TCP/IP Parameters Configuration The parameters are described as follows: • Interface – the LAN interface must use Ethernet/Fast Ethernet and is displayed here. This setting cannot be adjusted. • IP Address – this is the router’s IP Address f...

DI-1162 Remote Access Router 124 PROM System Configuration System Reset The system reset function enables you to reset the DI-1162 withoutpowering off. Some settings changes require a system reset in order forthem to take effect. A system reset will not affect the router’s settings, but will clear a...

DI-1162 Remote Access Router 126 PROM System Configuration • Last Boot Server IP Address – this shows the last boot server used to download an image file. This is for reference only. • Last IP Address – this shows the last IP address used for the LAN interface. Again, this is for reference only. The...

DI-1162 Remote Access Router PROM System Configuration 127 Please make sure you wish to wipe out all settings and configure therouter from scratch before you perform a factory reset. Execute Bootload Choosing this option accepts the changes made in the PROM programand begins the router’s startup seq...

DI-1162 Remote Access Router Using Telnet 129 Using Telnet The DI-1162 router can be configured and managed using telnet.Telnet accesses the same built-in configuration program as the RS-232Diagnostic port console connection. As such, all settings that can beadjusted through the console can also be ...

DI-1162 Remote Access Router 130 Using Telnet The router can now be accessed via the LAN by the includedWindows-based Configuration program, Telnet and SNMPmanagement applications. For more detailed information regardingthese procedures, please refer to the Connecting the Router section of this manu...

DI-1162 Remote Access Router Using RADIUS Authentication 131 Using RADIUS Authentication In addition to the dial-in user list, which can hold up to eight users, thismodel also supports an external authentication server which mayprovide password storage and usage accounting for thousands of users. In...

DI-1162 Remote Access Router 132 Using RADIUS Authentication Items in the above submenu are described as follows: ♦ RADIUS State – enables/disables Radius. ♦ Type – refers to the type of external password protocol. Currently, only Radius is supported. ♦ Server IP Address – this is the IP Address of ...

DI-1162 Remote Access Router Using RADIUS Authentication 133 192.168.0.1 1234 should be added to the client file. The Client Name field in the file gives the IP address of the DI-1162, and the Key field should be thesame as the Key field in the Radius Configuration submenu. After a RADIUS server has...

DI-1162 Remote Access Router 136 Appendix A – Cables and Connectors 14 14 TXD BA DTE 15 15 TXD CLK DB DCE 16 16 RXD BB DCE 17 17 RXD CLK DD DCE 18 18 Local Loopback LL DTE 19 19 RTS CA DTE 20 20 DTR CD DTE 21 21 Remote Loopback RL DTE 22 22 DSR CC DCE 23 23 DTR CD DTE 24 24 TXD CLK DA DTE 25 25 Test...

DI-1162 Remote Access Router Appendix A – Cables and Connectors 137 18 10 Local Loopback LL DTE 19 25 RTS CA DTE 20 12 DTR CD DTE 21 14 Remote Loopback RL DTE 22 29 DSR CC DCE 23 30 DTR CD DTE 24 17 TXD CLK DA DTE 25 18 Test Mode TM DCE End Connector: DB-25 Pin Female (ISO-2110)DB-37 Pin Male Cable ...

DI-1162 Remote Access Router Appendix B – Specifications 139 Appendix B – Specifications General Network Protocols: IP (Internet Protocol) WAN Protocols: PPP (Point-to-Point Protocol)Multi-Link PPP, SLIP, HDLC Routing Protocols: RIP and RIP V2.0DVMRP, IGMP Management: Local RS-232 Console Port (out-...

DI-1162 Remote Access Router Appendix C - IP Concepts 141 Appendix C - IP Concepts This appendix describes some basic IP concepts, the TCP/IP addressing scheme andshow how to assign IP Addresses. When setting up the router, you must make sure all ports to be utilized on the router havevalid IP addre...

DI-1162 Remote Access Router 142 Appendix C - IP Concepts Networks attached to the Internet are assigned class types that determine the maximumnumber of possible hosts per network. The previous figure illustrates how the net andhost portions of the IP address differ among the three classes. Class A ...

DI-1162 Remote Access Router Appendix C - IP Concepts 143 The value(s) in the host portion of a physical device's IP address can be in the range of 0through 255 as long as this portion is not all-0 or all-255. Values outside the range of 0to 255 can never appear in an IP address (0 to 255 is the ful...

DI-1162 Remote Access Router Appendix D – IP Protocol and Port Numbers 145 Appendix D – IP Protocol and PortNumbers Common Internet service protocols and IP port numbers. IP Protocol Numbers Protocol # Protocol Name Description 1 ICMP Internet Control Message [RFC792] 2 IGMP Internet Group Managemen...

DI-1162 Remote Access Router Appendix E – Configuration File 147 Appendix E – Configuration File The router can be configured when performing a Software Update through a configuration file. The configuration file can hold many settings for the router includingIP Addresses for all ports, path to the ...

DI-1162 Remote Access Router 148 Appendix E – Configuration File Configuration File Example # The system configuration file for D-Link DI-1162 RemoteAccess Router # DI-1162 runtime image file name (software update path andfile name)di1162-imaged:\project\di1162\runtime\image\1162run\1162run.hdr # sy...

DI-1162 Remote Access Router 151 Index A Access Right ........................44Admin[istration] Configuration ........................................100 Advanced Functions ............47Age ....................................104ARP request .........................50Async PPP .......................

DI-1162 Remote Access Router 152 Index dialing out ............................23Dial-out ................................21dial-out connections .............47Dial-Out Network Connections ..........................................49 Direction ..............................56DNS .......................

DI-1162 Remote Access Router Index 155 Software Update Control125, 126 Static ARP ...........................74Static ARPs..........................50Static IP Pool .......................64Static NAPT.........................86Static NAT ...........................86Statistics.........................

Offices AUSTRALIA D-LINK AUSTRALIA PTY.LTD. Unit 16, 390 Eastern Valley Way Roseville, NSW 2069 Australia TEL: 61-2-9417-7100 FAX: 61-2-9417-1077 TOLL FREE: 180017710 WEB: www.dlink.com.au E-MAIL: [email protected] CANADA D-LINK CANADA, INC. 2180 Winston Park Drive, Oakville, Ontario L6H 5W1 Canada ...