Curtis 4000 - Manuals - manualsarea.com

Page 5 - Wiring Instructions

TRACTOR CAB INC. August 2001 1164 4 STEP 1: TAKE HARNESS ASSEY.AND ROUTE FROM THE REAR OF THE VEHICLE TO THE FRONT. ROUTE HARNESS ALONG FRAME AND ATTACH TO FRAME HOLES AND FRAME SUPPORTS. IT IS NOT RECOMMENDED TO ATTACH TOFUEL OR BRAKE LINES FOR OBVIOUS REASONS. DO NOT ROUTE CLOSE TO EXHAUST SYSTEM ...

Page 6 - Control Parts / Wiring Schematic

TRACTOR CAB INC. August 2001 1165 5 Item No. Part No. Description Qty. 1CS1P39 Male Splice Cord - 18” 1 1CS1P38 Female Splice Cord - 18” 1 1CS1P35 Wiring Harness - 24’ 1 1CS1P36 Dust Cover 1 1CS1P32 Controller 1 1CS4P25 Fast-Cast 4000 Controller 1 1CS4P26 Fast-Cast 4000 Wiring Harness - 25' 1 1CS4P2...

Page 7 - Operating the Spreader; Preparation; Caution –; Spreader Loading; Warning –; Spreading Tips

TRACTOR CAB INC. August 2001 1166 6 Operating the Spreader Preparation Caution – Sweep area clear of foreign objects or obstacles that could cause personal injury. Keep other persons, children, or animals out of the area to be spread. Spreader Loading Warning – Do not overload vehicle. Use chart bel...

Page 8 - Spreader Operation; status with warning protection and built-in Vibrator Switch.; Troubleshooting Guide

TRACTOR CAB INC. August 2001 1167 7 Operating the Spreader (cont.) Spreader Operation Fast-Cast 2000 / Fast-Cast 3000 • The variable speed controller has finger-tip dial action, digital system status with warning protection.• To start, press power switch on controller and spreader will accelerate to...

Page 9 - Schematic Assembly

TRACTOR CAB INC. August 2001 1168 8 Item No. Part No. Description Qty. 1CS1P8 3/8'' - 16'' x 1'' Hex Bolt 10 1CS1P9 3/8'' - Locknut 10 1CS1P41 3/8'' Flat Washer 2 1SM1P3 2-5/16' Hair Pin Clip 1 1SM1P2 5/8'' x 5-1/2'' Hitch Pin 1 1CS2P15 3/8'' Fender Washer 4 1CS1P53 Transmission 1 1CS1P25 1/4'' - 20...

Page 10 - Fast-Cast 175 Assembly Instructions

TRACTOR CAB INC. August 2001 1169 9 1. Install foam tape on bottom of motor enclosure/frame assembly. 2. Bolt bottom cover assembly on to motor enclosure. Make sure 2'' square tube faces the rear. 3. Attach bulkhead cable fitting onto cable outer jacket. Using pliers to hold the cable, thread fittin...

Page 11 - Fast-Cast 175 Wiring Instructions

TRACTOR CAB INC. August 2001 1170 10 1. First, install switch at desired location. This will determine what your proper wire length is to be. 2. Run spreader/vehicle harness from the rear of vehicle to switch area. Remove approx. 3'' of the black outer jacket exposing two single leads (red and black...

Page 12 - Wiring Schematic

TRACTOR CAB INC. August 2001 1171 11 Item No. Part No. Description Qty. 1CS2P25 On/Off Switch 1 1CS2P26 Butt Connector 1 1CS1P52 Dielectric Grease 1 1CS2P27 20' Vehicle Harness 1 1CS2P28 10' Battery Harness 1 1CS2P29 Rubber Switch Boot 1 1CS2P30 Spreader Splice Cord - 10'' 1 1CS2P31 Harness Splice C...

Page 13 - Maximum Load Weight Not To Exceed 240 lbs. Gross

TRACTOR CAB INC. August 2001 1172 12 Drop Utility Mount Schematic Assembly Item No. Part No. Description Qty. 1SM3P4 1/2’’ Flat Washer 2 1CS1P11 1/2’’-Lock Nut 2 1CS1P8 3/8’’-16x1 Hex Bolt 2 1CS1P9 3/8’’-Lock Nut 8 1CS1P41 3/8’’ Flat Washer 9 1SM1P3 2 - 5/16'' Hair Pin Clip 2 1SM1P2 5/8'' x 5-1/2'' ...

Page 17 - Complete Drive Assembly Schematic

TRACTOR CAB INC. August 2001 1176 16 Complete Drive Assembly Schematic Item No. Part No. Description Qty. 1CS1P16 Motor 12 Volt DC 1 1CS1P53 Transmission 1 1CS1P17 Motor Cover 1 1CS1P13 Drive Enclosure 1 1CS3P7 Fast-Cast 3000 Power Cable 1 1CS1P21 Fast-Cast 2000 Power Cable 1 1CS1P19 Auger 1 1CS1P22...

Page 19 - Swing Away – Pivot Mount

TRACTOR CAB INC. August 2001 1178 18 Item No. Part No. Description Qty. 1CS1P10 1/2” 13 x 1 1/2” Hex Bolt 2 1SM3P4 1/2” Flat Washer 7 1CS1P11 1/2” Lock Nut 5 1CS1P8 3/8” 16 x 1” Hex Bolt 16 1CS4P1 3/8” 16 x 1 1/2” Hex Bolt 13 1CS1P9 3/8” Lock Nut 29 1CS1P41 3/8” Flat Washer 9 1SM5P1 5/16” Lock Nut 1...

Page 21 - Swing Away - Pivot Mount Installation Schematic

TRACTOR CAB INC. August 2001 1180 20 Fig. A Fig. B Fig. C Fig. D Fig. E Fig. F Fig. G Fig. H Fig. I DRILL DRILL DRILL Swing Away - Pivot Mount Installation Schematic

Page 22 - Troubleshooting; PROBLEM POSSIBLE

TRACTOR CAB INC. August 2001 1181 21 Loose electrical connections.Blown Fuse.Motor Seized. Jammed auger. Poor electrical connections. Electrical short.Controller Bad. No material in hopper. Wet material. Frozen or coarse material. Spinner not turning. Auger loose on shaft. Troubleshooting Whenever s...