Cub Cadet Z - Wing 48 - Manuals

6 SAFETY DECALS AND LABELS WARNING SHIELD MISSING DO NOT OPERATE Part Number: 00030635 Part Number: 777S30503 KEEP HANDS and FEET AWAY DANGER T O R E D U C E T H E R I S K O F I N J U R Y, D O N O T O P E R A T E M O W E R U N L E S S DIS C HA RGE C HU TE COV ER OR GR A SS C AT C H E R I S I N I T S...

7 SPECIFICATIONS Engine: 23HP Kohler Type: Ver tical air cooled V-Twin Air Cleaner: Paper Element Lube System: Pressurized with oil filter Starter: 12-volt electric Traction Drive: Variable-speed hydraulic pumps with wheel motors on each drive wheel Hydraulic Tank: 2 qua rt capacity, One pint filter...

8 OPERATING INSTRUCTIONS A.General 1. When Mowing: a. Keep adults, children, and pets away from the area to be mowed. b. When operating this mower, in the forward direction, do not allow the steering levers to return to Neutral on their own. Always maintain a firm grip on the levers, operate them sm...

10 4. Electric Blade Clutch Switch: (See Figure 1.) Located on the seat support beside the ignition switch. This is an “on/off” push pull switch that controls the electric blade clutch which supplies power to the cutting blades through the PTO. The switch must be turned off to start the engine and s...

11 C.Initial Adjustments 1. Check the fluid levels and tires: Note: These checks should be made daily, before starting the engine. a. Fuel: Using a good grade of unleaded, regular gasoline (for a gasoline engine), fill the fuel tank (beside the engine on the left or right side of the mower). When th...

14 f. Fold in the steering levers to the operating position. WARNING: When operating this mower forward, do notallow the steering levers to return to the neu-tral position on their own. Always maintain afirm grip on the steering levers, operate themsmoothly and avoid any sudden movements ofthe lever...

15 f. Remove three hairpins from the deck (See Fig. 5). Remove the (2) hairpins on the left and right rear side of the cutter deck, and (1) hairpin from the front of the deck. g. Turn front caster wheels outward. h. Shift the deck toward the operator’s left side of the mower and remove. i. To instal...

16 d. Remove tension of the PTO belt by moving the belt tensioning rod. Loosen the belt retaining bolt. e. Pull the tensioner pulley away from the belt and remove the PTO belt then remove the blade drive belt. f. Reverse the process to install the belt. Note: When replacing belts do not over- tighte...

17 caps and drain oil from both left and right pumps. Replace and retighten nuts. j. Coat new filter seal with oil before installa- tion. Install new hydraulic oil filter filled with new oil. k. Add proper amount of hydraulic oil to res- ervoir. l. Run and purge gearboxes. Check oil level. m. Add pr...

18 other electrical components. This is a stan-dard plug-in type automotive fuse rated at 7.5 amp. 7. Safety Switches: There are five safety switches in the electrical circuit which control the engine. They are (1) the blade clutch switch, (2) the parking brake switch, (3) the left and (4) the right...

19 seat against spring pressure, and swing one of the steering levers up to the operat-ing position. Release the operator’s seat and the engine should stop. If the engine does not stop, the seat switch must be replaced. With both steering levers folded out in the neutral position, the parking brake ...

20 opened-out position. If your mower creeps do the following. a. Jack up rear of unit.b. Place Lapbars in neutral opened-out posi-tion. c. Locate jam nuts. (Reference control assembly in parts list). d. Loosen jam nuts on both ends of rod con- nectors. See Control Assembly in the Illus-trated Parts...

21 purge any air from the system. Shut off the engineand recheck the oil level in the tank. Top-off ifnecessary until the oil level is up to the second hole inthe fill tube. Note: After unit is up to operating tempera- ture, turn off engine and re-check hydraulic oil. If oil appears foamy or contain...

22 leys and blades. (Be careful not to get any oil on the drive belts.) d. Lubricate the mower. e. Drain the engine oil. The engine should be warm so that all the oil drains. Replace the engine oil filter and refill the crankcase with fresh oil. f. Gasoline Engine: Drain all the fuel. Close the fuel...

23 . OIL CHART Apply a few drops of SAE 20W-50 engine oil or use a spray lubricant. Apply the oil to both sides of pivot points. Wipe off any excess. Start engine and operate mower briefly to insure that oil spreads evenly. Number of Oil Points Description DAILY 44222212 WEEKLY 1222111422 Deck Suspe...

24 Performance Adjustments A. High Speed Tracking Adjustment If mower tracks to one side with both lap bars in fully forward position: 1. Check air pressure in all four tires: a. Pressure should be within specified ranges and balanced side-to-side. b. Rear tires 8-10 psi. recommended (20 psi MAX.) c...

29 SLOPE GAUGE Do not mo w o n i n c lines with a s lope i n ex c e s s of 15 d egrees (a ri s e of approx im at el y 2-1/ 2 feet ev ery 10 f eet ). A ri di ng mo wer c ould ov ertu rn and c a use s e ri ous i n ju ry . I f opera tin g a wal k -be h ind m o wer on s u c h a s lope, i t i s ex tr em ...

30 MAINTENANCE RECORD DATE WORK PERFORMED DATE WORK PERFORMED

MANUFACTURER’S LIMITED WARRANTY - TURF EQUIPMENT This warranty is specific to the product manual to which it is attached. For a complete list of products and warranties contact your authorized Cub Cadet Commercial dealer. Proper maintenance of the purchased Cub Cadet Commercial equipment is the owne...

6 SAFETY DECALS AND LABELS WARNING SHIELD MISSING DO NOT OPERATE Part Number: 00030635 Part Number: 777S30503 KEEP HANDS and FEET AWAY DANGER T O R E D U C E T H E R I S K O F I N J U R Y, D O N O T O P E R A T E M O W E R U N L E S S DIS C HA RGE C HU TE COV ER OR GR A SS C AT C H E R I S I N I T S...

7 SPECIFICATIONS Engine: 23HP Kohler Type: Ver tical air cooled V-Twin Air Cleaner: Paper Element Lube System: Pressurized with oil filter Starter: 12-volt electric Traction Drive: Variable-speed hydraulic pumps with wheel motors on each drive wheel Hydraulic Tank: 2 qua rt capacity, One pint filter...

8 OPERATING INSTRUCTIONS A.General 1. When Mowing: a. Keep adults, children, and pets away from the area to be mowed. b. When operating this mower, in the forward direction, do not allow the steering levers to return to Neutral on their own. Always maintain a firm grip on the levers, operate them sm...

10 4. Electric Blade Clutch Switch: (See Figure 1.) Located on the seat support beside the ignition switch. This is an “on/off” push pull switch that controls the electric blade clutch which supplies power to the cutting blades through the PTO. The switch must be turned off to start the engine and s...

11 C.Initial Adjustments 1. Check the fluid levels and tires: Note: These checks should be made daily, before starting the engine. a. Fuel: Using a good grade of unleaded, regular gasoline (for a gasoline engine), fill the fuel tank (beside the engine on the left or right side of the mower). When th...

14 f. Fold in the steering levers to the operating position. WARNING: When operating this mower forward, do notallow the steering levers to return to the neu-tral position on their own. Always maintain afirm grip on the steering levers, operate themsmoothly and avoid any sudden movements ofthe lever...

15 f. Remove three hairpins from the deck (See Fig. 5). Remove the (2) hairpins on the left and right rear side of the cutter deck, and (1) hairpin from the front of the deck. g. Turn front caster wheels outward. h. Shift the deck toward the operator’s left side of the mower and remove. i. To instal...

16 d. Remove tension of the PTO belt by moving the belt tensioning rod. Loosen the belt retaining bolt. e. Pull the tensioner pulley away from the belt and remove the PTO belt then remove the blade drive belt. f. Reverse the process to install the belt. Note: When replacing belts do not over- tighte...

17 caps and drain oil from both left and right pumps. Replace and retighten nuts. j. Coat new filter seal with oil before installa- tion. Install new hydraulic oil filter filled with new oil. k. Add proper amount of hydraulic oil to res- ervoir. l. Run and purge gearboxes. Check oil level. m. Add pr...

18 other electrical components. This is a stan-dard plug-in type automotive fuse rated at 7.5 amp. 7. Safety Switches: There are five safety switches in the electrical circuit which control the engine. They are (1) the blade clutch switch, (2) the parking brake switch, (3) the left and (4) the right...

19 seat against spring pressure, and swing one of the steering levers up to the operat-ing position. Release the operator’s seat and the engine should stop. If the engine does not stop, the seat switch must be replaced. With both steering levers folded out in the neutral position, the parking brake ...

20 opened-out position. If your mower creeps do the following. a. Jack up rear of unit.b. Place Lapbars in neutral opened-out posi-tion. c. Locate jam nuts. (Reference control assembly in parts list). d. Loosen jam nuts on both ends of rod con- nectors. See Control Assembly in the Illus-trated Parts...

21 purge any air from the system. Shut off the engineand recheck the oil level in the tank. Top-off ifnecessary until the oil level is up to the second hole inthe fill tube. Note: After unit is up to operating tempera- ture, turn off engine and re-check hydraulic oil. If oil appears foamy or contain...

22 leys and blades. (Be careful not to get any oil on the drive belts.) d. Lubricate the mower. e. Drain the engine oil. The engine should be warm so that all the oil drains. Replace the engine oil filter and refill the crankcase with fresh oil. f. Gasoline Engine: Drain all the fuel. Close the fuel...

23 . OIL CHART Apply a few drops of SAE 20W-50 engine oil or use a spray lubricant. Apply the oil to both sides of pivot points. Wipe off any excess. Start engine and operate mower briefly to insure that oil spreads evenly. Number of Oil Points Description DAILY 44222212 WEEKLY 1222111422 Deck Suspe...

24 Performance Adjustments A. High Speed Tracking Adjustment If mower tracks to one side with both lap bars in fully forward position: 1. Check air pressure in all four tires: a. Pressure should be within specified ranges and balanced side-to-side. b. Rear tires 8-10 psi. recommended (20 psi MAX.) c...

29 SLOPE GAUGE Do not mo w o n i n c lines with a s lope i n ex c e s s of 15 d egrees (a ri s e of approx im at el y 2-1/ 2 feet ev ery 10 f eet ). A ri di ng mo wer c ould ov ertu rn and c a use s e ri ous i n ju ry . I f opera tin g a wal k -be h ind m o wer on s u c h a s lope, i t i s ex tr em ...

30 MAINTENANCE RECORD DATE WORK PERFORMED DATE WORK PERFORMED

MANUFACTURER’S LIMITED WARRANTY - TURF EQUIPMENT This warranty is specific to the product manual to which it is attached. For a complete list of products and warranties contact your authorized Cub Cadet Commercial dealer. Proper maintenance of the purchased Cub Cadet Commercial equipment is the owne...