Cub Cadet ogst3305- Manuals

Page 2 - TRAINING; IM POR TANT SAFE OP ER A TION PRAC TICES; LO CATE YOUR MODEL NUMBER AND SE RIAL NUMBER; You must have these num bers, along with the date and proof of

TRAINING 1. Read, un der stand, and fol low all in struc - t i o n s o n t h e m a c h i n e a n d i n t h eman ual(s) be fore at tempt ing to as sem -ble and op er ate. Keep this man ual in asafe place for fu ture and reg u lar ref er -e n c e a n d f o r o r d e r in g r e p l a c e m e n tparts. ...

Page 4 - MAIN TE NANCE AND STOR AGE; utes to clear snow from ma; WARNING - Your Re spon si bil ity

10. Plan your snow throw ing pat tern to avoid dis charge to wards win dows, walls, cars etc. To avoid prop erty dam age or per - sonal in jury caused by a ric o chet. 11. Never di rect dis charge at chil dren, by - stand ers and pets or al low any one in front of the ma chine. 12. Do not over load ...

Page 5 - ASSEMBLY INSTRUCTIONS; AUGER SHEAR BOLTS

ASSEMBLY INSTRUCTIONS NOTE: The snowthrower is shipped with oil and WITH OUT GAS O LINE. Af ter as sem bly, re fer to sep a rate en gine man ual for properfuel and en gine oil rec om men da - tions. AUGER SHEAR BOLTS The au gers are se cured to the spi ral shaft with two shear bolts and hexflange lo...

Page 6 - BE FORE STARTING; The crank; fore fill; OP ER A TION; TO START ENGINE

• Re move the hair pin clip from the end of the up per chute crank. Slide the up perchute crank into the lower chute crank.Align the holes, and se cure with hair pinclip. See Fig ure 4. • The ca ble ties nor mally are loosely in - stalled on each side of the lower han dle at the fac tory. Pull the c...

Page 7 - Al; FULL CHOKE

• Make cer tain the au - ger and drive clutchle vers are in the dis - e n g a g e d ( r e l e a s e d )po si tion. • Move throt tle con trol up to FAST po si - t i o n . I n s e r t i g n i t i o nkey into slot. See Fig ure 7. Be cer tain itsnaps into place. Do not turn key. Elec tric Starter (Op ti...

Page 8 - CONTROLS

NOTE: Al ways cover vent hole in primer but ton when push ing. Ad di - tional prim ing may be nec es sary for first start if tem per a ture is be low 15°F. • Grasp starter han dle (see Fig ure 7) and pull rope out slowly, un til it pulls slightly harder. Let rope re wind slowly. • Pull starter han d...

Page 10 - ADJUSTMENTS; Fail; LUBRICATION

ADJUSTMENTS WARNING: NEVER at tempt toclean chute or make any ad just -ments while en gine is run ning. REMOTE CHUTE ASSEMBLYADJUSTMENT The re mote chute con trol ca bles have been pre-ad justed at the fac tory. Move the re mote chute le ver on the con trol panel back and for ward to ad just an gleo...

Page 11 - MAINTENANCE; AUGERS; Some mod

ENGINE Re fer to en gine man ual for en gine lu bri ca -tion in struc tions. WARNING: When fol low ing in -struc tions in sep a rate en gineman ual for drain ing oil, be sureto pro tect frame to avoid oildrip ping onto trans mis sionparts. HEX SHAFT Lu bri cate the gear (hex) shaft with a lightweigh...

Page 13 - To Re move the Au ger Drive Belt:

• Re move the large shoul der bolt and washer on the left hand side of the en -gine pul ley with an ad just able wrench. See Fig ure 15. NOTE: Ref er ence to right hand or left hand side of ma chine are ob - served from the op er at ing po si tion. • Re move the cot ter pin and washer from the fer r...

Page 14 - See Ad just ment sec tion for; To Remove the Drive Belt:

NOTE: See Ad just ment sec tion for "Au ger Belt Ad just ment". To Remove the Drive Belt: a. Pull idler pul ley away from belt. See Fig ure 19. b. Re move drive belt from the en gine pul ley and bot tom drive pul ley. c. Re place belt and re as sem ble in re - verse or der. • Re as sem ble t...

Page 15 - STORAGE INSTRUCTIONS; age as in

• Po si tion the fric tion wheel as sem bly uponto the pin of the shift rod as sem bly and slide the shaft through the fric tionwheel. See Fig ure 21. • Slide the hex shaft into the hex I.D. ofthe sprocket, the spacer and the leftb a l l b e a r in g a n d s e c u r e w i t h t h ecupped washer and ...

Page 16 - TROU BLE SHOOTING

TROU BLE SHOOTING PROB LEM POS SI BLE CAUSE(S) COR REC TIVE AC TION En gine fails to start 1. Fuel tank empty, or stale fuel. 2. Blocked fuel line. 3. Choke not in the FULL po si tion. 4. Faulty spark plug. 5. Safety key not in ig ni tion switch on en gine. 6. Spark plug wire dis con nected. 7. Prim...

Page 18 - Do not over; SUP PLE MENT; MONTAGE DE LA GOULOTTE; Ne serrez pas

IN STRUC TIONS FOR AT TACH ING THE CHUTE AS SEM BLY • P l a c e c h u t e a s s e m b l y o v e r c h u t e o p e n in g , w i t h t h e o p e n in g i n t h echute as sem bly fac ing the front of the unit. Place chute flange keep ers be - neath lip of chute as sem bly, with theflat side of chute fl...