Cub Cadet 7252 - Manuals

7 SAFETY LABELS STARTING INSTRUCTIONS 1. KNOW THE OPERATING AND SAFETY INSTRUCTIONS IN THE OPERATORS'S MANUAL AND ON THE TRACTOR. 2. MOVE THROTTLE TO MID POSITION AND DEPRESS BRAKE PEDAL. 3. TURN KEY TO THE START POSITION. 1. DISENGAGE PTO AND SET PARKING BRAKE. 2. MOVE THROTTLE CONTROL TO MID POSIT...

8 SAFETY LABELS (Cont.) WARNING B AT T E R I E S C O N TA I N A C I D A N D E X P L O S I V E G A S . E X P L O S I O N C A N R E S U LT F R O M S P A R K S , F L A M E S , O R W R O N G C A B L E C O N N E C T I O N S . T O C O N N E C T J U M P E R C A B L ES O R C H A R G ER S E E M A N U A L F O...

9 SECTION 1: CONTROLS AND FEATURES FLOORBOARD AND DASH PANEL MOUNTED CONTROLS Figure 1 B C D E F G H J K L M N A ABCDEF GHJKLMN Steering WheelPTO SwitchThrottle HandleIgnition SwitchBrake PedalForward/Reverse Pedal Seat Adjustment LeverDifferential Lock PedalParking Brake LeverChoke Control Knob Haz...

13 FENDER MOUNTED CONRTOLS AND FEATURES Figure 12 A B N D E F G H K J H J K L G C M A. Fuel Fill Cap The fuel fill cap is located on the left fender besidethe operator’s seat. WARNING: Never fill the fuel tank tothe top of the filler neck. Expansioncould result in overflow, allowinghighly flammable ...

14 E. Transmission Hi/Lo Range Shift Lever The Hi/Lo range shift lever is located on the rightfender. The lever has two speed range settings anda neutral position. The lever must be shifted intoeither the high or low range prior to depressing theforward/reverse pedal to drive the tractor. • Push the...

15 SECTION 2: OPERATION ROLLOVER PROTECTIVE STRUCTURE (ROPS) This tractor is equipped with a Rollover ProtectionStructure (ROPS) and seat belts. When usedtogether they are effective in reducing injuries to theoperator in the event of an accidental tractorrollover. The safety provided by the ROPS ism...

16 The fuel fill cap is located on the fender to the left ofthe seat. Unscrew the fuel cap and fill tank from anapproved gasoline container. Immediately wipe upany spilled fuel. WARNING: Never fill the fuel tank tothe top of the filler neck. Expansioncould result in overflow through thevents in the ...

17 USING JUMPER CABLES TO START THE ENGINE WARNING: Batteries contain sulfuricacid and produce explosive gasses.Make certain the area is well ventilated,wear gloves and eye protection, andavoid sparks or flames near the battery. If the battery loses power and is unable toadequately crank the engine ...

18 Avoid stopping when driving up a slope. If it isnecessary to stop while driving up a slope, start upsmoothly and carefully to reduce the possibility offlipping the tractor over backward. STOPPING THE TRACTOR • Fully depress the brake pedal to bring thetractor to a complete stop. Push downward ont...

19 WARNING: Always maintain a tractorspeed that allows for complete controland stability of the machine. Be awareof dangerous areas or conditions. NEUTRAL — Disengages the transmissiondrive. Shift the lever to the center of the slot.Use ONLY for towing or moving the tractorwhen not under power. USIN...

20 USING THE PTO SELECTION LEVER The position of the PTO selection lever will deter-mine whether the rear PTO, mid PTO, or bothPTO’s will be engaged when the PTO switch isactivated. WARNING: NEVER shift the PTO selec-tion lever while the PTO is engaged.Damage to internal components willoccur. • Shif...

23 SECTION 3: ADJUSTMENTS ADJUSTING THE SEAT For the comfort of the operator, a single leveradjustable seat is provided to set the fore to aftposition of the seat. Adjust the seat to the mostcomfortable position that allows you to operate allcontrols and pedals. WARNING: Do not adjust the seat whent...

24 • The length of the upper hitch link is normallydetermined by the design of each implement.To adjust the upper hitch link, loosen the jamnut and turn the adjustment tube as shown inFigure 25. After the appropriate length is at-tained, tighten the jam nut. If correctly adjusted,the upper hitch lin...

25 ADJUSTING THE BRAKES The tractor brakes are adjusted at the factory andshould experience minimal wear if the tractor isoperated normally. However, all brake pads aresubject to wear and at some point the brake linkagemay have to be adjusted. Check the brake linkage as follows: • Place the tractor ...

26 SECTION 4: TRACTOR MAINTENANCE The service life and reliability of any machinedepends upon the care it is given. Proper lubrica-tion and maintenance is a vital part of that care.Using the Lubrication and Maintenance Chart as aguide, monitor the hourmeter on the instrumentpanel to ensure the requi...

27 LUBRICATION AND MAINTENANCE CHART (ILLUSTRATION) 1 2 1 8 1 2 5 6 3 4 2 0 6 6 9 8 7 7 1 0 1 0 1 1 1 3 1 5 1 4 1 7 1 6 2 0 1 9 2 1 1 9

28 LUBRICATION AND MAINTENANCE CHART † More often when operating under dusty conditions. Ref. No. Operation to be Performed Service Intervals B e fo re e a c h u s e E v e ry 1 0 H o u rs E v e ry 2 5 H o u rs E v e ry 5 0 H o u rs E v e ry 1 0 0 H o u rs E v e ry 2 0 0 H o u rs E v e ry 3 0 0 H o u...

29 ACCESSING THE ENGINE COMPARTMENT WARNING: If the tractor has beenrecently operated, engine surfaces(including the radiator) will be HOT.Allow the engine to cool before open-ing the hood, or use extreme cautionto avoid burns when the hood is open. To raise the hood, locate the latch release lever ...

30 • Since battery acid is corrosive, do not pour itinto any sink or drain. Before discarding anempty electrolyte container, rinse it thoroughlywith a neutralizing solution. • NEVER connect (or disconnect) battery chargerclips to the battery while the charger is turnedon, as it can cause sparks. • K...

31 HEAD LIGHT BULB REPLACEMENT The tractor is equipped with four headlight bulbs. Ifone of the bulbs should burn out, replace the bulbas follows: • Fully raise the hood so that the hood prop linkholds the hood in the raised position. • Pull both locking tabs of the wire harness plugaway from the bul...

32 INSTRUMENT PANEL BULB REPLACEMENT Referring to the instrument panel information pro-vided in the CONTROL AND FEATURES sectionof this manual, regularly check to ensure that theinstrument panel light bulbs are functioning. To change a burned out instrument panel bulb: • Raise the tractor hood to vi...

33 Main Fuse The main fuse in the tractor wire harness protectsthe tractor’s entire electrical system. A blown mainfuse will prevent battery current from passingthough the harness. To replace the main fuse: • Raise the tractor hood and remove the rightside panel. • Locate the main fuse under the das...

34 • If the oil level is low, add Cub Cadet hydraulicoil. Loosely position a funnel in the fill hole sothat there is enough clearance around the fun-nel to allow the transmission to vent while theoil is poured into the transmission. Fill ONLY tothe full mark, never overfill the transmission. NOTE: A...

35 CHANGING HYDROSTATIC TRANSMISSION AND HYDRAULIC SYSTEM OIL FILTERS NOTE: Except for the initial break-in period oil filterchange, the hydrostatic transmission and hydraulicsystem oil filters should be changed along with thehydrostatic transmission / hydraulic system oil afterevery 200 hours of op...

36 LUBRICATION OF DRIVE SHAFT Lubricate both ends of the drive shaft after every 50hours of operation as follows: • The front end of the drive shaft can beaccessed from under the hood, and the rearend by removing the six screws and the centerfender cover. The drive shaft can also beaccessed from the...

37 TRACTOR STORAGE If your tractor is not going to be operated for anextended period of time (thirty days to approxi-mately six months), the tractor should be preparedfor storage. Store the tractor in a dry and protectedlocation. If stored outside, cover the tractor (includ-ing the tires) to protect...

38 SECTION 5: ENGINE INFORMATION AND MAINTENANCE KAWASAKI LIMITED WARRANTY CALIFORNIA AND FEDERAL EMISSIONS CONTROL SYSTEMS SMALL OFF-ROAD ENGINES The California Air Resources Board, the Environmental Protection Agency (EPA) , and Kawasaki Motors Corp.,U.S.A. (hereinafter “Kawasaki”) are pleased to ...

39 3. LIMITED LIABILITY. (a) The liability of Kawasaki under this Emission Control Systems Warranty is limited solely to the remedying of defects in materials or workmanship by any authorized Kawasaki small off-road engine dealer at itsplace of business during customary business hours. This warranty...

40 ENGINE MAINTENANCE WARNING: Use care when servicingany component in the engine area. Ifthe engine has recently been operated,components will be hot and couldcause burns. Allow the engine to coolbefore servicing. WARNING: Before servicing the engine,place the tractor on a level surface,stop the en...

42 • Turn the valve drain cock fully clockwise toclose the valve, and clean any residual oil fromthe valve. Refer to Figure 48. • Apply a light coating of clean oil on the gasket ofthe new oil filter. Thread the filter on by handuntil the gasket contacts the filter mounting sur-face, then tighten th...

43 INSPECTION OF COOLING SYSTEM HOSES Check the cooling system hoses for any cracks ordeterioration every 200 hours of operation. Checkall hose connections for looseness. Replace anydamaged hoses and tighten any loose connections. CHANGING THE ENGINE COOLANT The engine coolant should be drained and ...

44 SERVICING THE FOAM PRECLEANER Wash the foam precleaner every 25 hours ofoperation. Wash more often when operating underextremely dusty conditions. Replace the precleanerif torn or otherwise damaged. Referring to Figure 52, wash the precleaner asfollows: • Remove the knob and lift off the air clea...

45 SECTION 6: SPECIFICATIONS Engine Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . KawasakiHorsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

46 SPECIFICATIONS Hydraulic Lift System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auxiliary Pump-GearControl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Position Contr...

47 SECTION 7: OPTIONAL EQUIPMENT AND ACCESSORIES When purchasing your tractor, you probably had it equipped for your particular needs at that time.You may later wish to obtain additional equipment or accessories to perform other tasks. Refer to thechart below for a list of optional equipment and acc...

6 • Maintain the weight balance of the tractor.Install front end weights to counterbalanceheavy implements attached to the three pointhitch. Do not operate the tractor with a lightfront end. • Any towed vehicle with a total weight exceedingthat of the tractor should be equipped its ownbraking system...

8 SAFETY LABELS STARTING INSTRUCTIONS 1. KNOW THE OPERATING AND SAFETY INSTRUCTIONS IN THE OPERATORS'S MANUAL AND ON THE TRACTOR. 2. MOVE THROTTLE TO MID POSITION AND DEPRESS BRAKE PEDAL. 3. TURN KEY TO THE START POSITION. 1. DISENGAGE PTO AND SET PARKING BRAKE. 2. MOVE THROTTLE CONTROL TO MID POSIT...

9 SAFETY LABELS (Cont.) WARNING B AT T E R I E S C O N TA I N A C I D A N D E X P L O S I V E G A S . E X P L O S I O N C A N R E S U LT F R O M S P A R K S , F L A M E S , O R W R O N G C A B L E C O N N E C T I O N S . T O C O N N E C T J U M P E R C A B L ES O R C H A R G ER S E E M A N U A L F O...

10 SECTION 1: CONTROLS AND FEATURES FLOORBOARD AND DASH PANEL MOUNTED CONTROLS Figure 1 B C D E F G H J K L M N A ABCDEF GHJKLMN Steering WheelPTO SwitchThrottle HandleIgnition SwitchBrake PedalForward/Reverse Pedal Seat Adjustment LeverDifferential Lock PedalParking Brake LeverChoke Control Knob Ha...

14 FENDER MOUNTED CONRTOLS AND FEATURES Figure 12 A B N D E F G H K J H J K L G C M A. Fuel Fill Cap The fuel fill cap is located on the left fender besidethe operator’s seat. WARNING: Never fill the fuel tank tothe top of the filler neck. Expansioncould result in overflow, allowinghighly flammable ...

15 E. Transmission Hi/Lo Range Shift Lever The Hi/Lo range shift lever is located on the rightfender. The lever has two speed range settings anda neutral position. The lever must be shifted intoeither the high or low range prior to depressing theforward/reverse pedal to drive the tractor. • Push the...

16 SECTION 2: OPERATION ROLLOVER PROTECTIVE STRUCTURE (ROPS) This tractor is equipped with a foldable RolloverProtection Structure (ROPS) and seat belts. Whenused together they are effective in reducing injuriesto the operator in the event of an accidental tractorrollover. The safety provided by the...

17 SAFETY INTERLOCK SYSTEM This tractor is equipped with a safety interlocksystem for the protection of the operator. If theinterlock system should ever malfunction, do notoperate the tractor. Contact your authorized CubCadet Dealer. The safety interlock system preventsthe engine from cranking or st...

18 • Move the throttle handle to midway betweenthe “SLOW” and “FAST” position. Refer toFigure 15. • Make sure the PTO switch is in the “OFF”position. Note: The PTO light on instrumentpanel will flash if switch is in ON position. Figure 15 • Either fully depress and hold the brake pedal orengage the ...

19 DRIVING THE TRACTOR WARNING: Avoid sudden starts, exces-sive speed and sudden stops. WARNING: Do not leave the seat of thetractor without disengaging the PTOand engaging the parking brake. Ifleaving the tractor unattended, turn theignition key off and remove key. • Adjust the operator’s seat to t...

20 Figure 16 • To move in reverse, check that the area behindis clear then slowly depress the rear of theforward/reverse pedal. • When traveling short distances with frequentchanges in direction, the forward/reverse rockerpedal may be operated using the heel/toemethod. Place your foot on the center ...

22 • Shift the PTO lever to the middle position toselect both the mid PTO and rear PTO. Themid PTO and rear PTO will run simultaneouslywhen the PTO switch is activated. NOTE: Occasionally you may not be able to shiftfrom one PTO selection to another due to a slightmisalignment between the internal s...

23 USING THE TOP LINK RETAINER HOOK The top link hook is provided to retain the the toplink of the three point hitch when not in use. To utilize the top link hook, proceed as follows: • While holding the top link upward, raise thehook rod and slide it fully to the left so that itlocks in the upright...

24 USING THE AUXILIARY HYDRAULIC VALVE (IF EQUIPPED) Some tractors may be equipped with an auxiliaryhydraulic valve package. This package providestwo hydraulic circuits for operating optionalequipment that can be installed on the tractor. The male and female hydraulic couplers, locatedbeneath the ri...

26 SECTION 3: ADJUSTMENTS ADJUSTING THE SEAT For the comfort of the operator, a single leveradjustable seat is provided to set the fore to aftposition of the seat. Adjust the seat to the mostcomfortable position that allows you to operate allcontrols and pedals. WARNING: Do not adjust the seat whent...

27 • The length of the upper hitch link is normallydetermined by the design of each implement.To adjust the upper hitch link, loosen the lock-ing lever and turn the adjustment tube asshown in Figure 29. After the appropriate lengthis attained, tighten the locking lever. If correctlyadjusted, the upp...

28 ADJUSTING THE BRAKES The tractor brakes are adjusted at the factory andshould experience minimal wear if the tractor isoperated normally. However, all brake pads aresubject to wear and at some point the brake linkagemay have to be adjusted. Check the brake linkage as follows: • Place the tractor ...

29 SECTION 4: TRACTOR MAINTENANCE The service life and reliability of any machinedepends upon the care it is given. Proper lubrica-tion and maintenance is a vital part of that care.Using the Lubrication and Maintenance Chart as aguide, monitor the hourmeter on the instrumentpanel to ensure the requi...

30 LUBRICATION AND MAINTENANCE CHART (ILLUSTRATION) 12 18 1 2 5 6 3 4 20 6 6 9 8 7 7 10 10 11 13 15 14 17 16 20 19 21 19

31 LUBRICATION AND MAINTENANCE CHART † More often when operating under dusty conditions. Ref. No. Operation to be Performed Service Intervals Be fo re eac h us e Ev er y 10 Ho ur s Ev er y 25 Ho ur s Ev er y 50 Ho ur s Ev er y 10 0 Ho ur s Ev er y 20 0 Ho ur s Ev er y 30 0 Ho ur s Ev er y 40 0 Ho ur...

32 ACCESSING THE ENGINE COMPARTMENT WARNING: If the tractor has beenrecently operated, engine surfaces(including the radiator) will be HOT.Allow the engine to cool before open-ing the hood, or use extreme cautionto avoid burns when the hood is open. To raise the hood, locate the latch release lever ...

33 • If acid spills on clothing, first dilute it with cleanwater, then neutralize with a solution ofammonia/water or baking soda/water. • Because battery acid is corrosive, do not pour itinto any sink or drain. Before discarding anempty electrolyte container, rinse it thoroughlywith a neutralizing s...

34 BATTERY STORAGE • When storing the tractor for extended periods,disconnect the battery cables. Removing thebattery from the unit is recommended. • All batteries discharge during storage. Keep theexterior of the battery clean, especially the top.A dirty battery will discharge more rapidly. • The b...

35 HAZARD BULB REPLACEMENT Flashing hazard lights are installed on each side ofthe ROPS. Replace the bulbs as follows: • Grasp the outer half of the light housing andboth the front and rear lenses. Accessing thescrews from the notches at the top and bottomof the outer housing, remove the two screwsf...

36 SERVICING ELECTRICAL SYSTEM Fuses are installed to protect the tractor’s electricalsystem from damage caused by excessive amper-age. Always use the same capacity fuse forreplacement. If the electrical system does not func-tion, check for blown fuses. See Figure 41If you have a recurring problem w...

37 Hazard Light Flasher Relay The flasher relay controls the on / off flashing of thehazard lights. If the hazard lights do not functionproperly, the flasher relay is probably faulty. Replace the relay as follows: • Remove the dash panel insert by removing thetwo screws. Refer to Figure 42. • Pull t...

39 CHANGING HYDROSTATIC TRANSMISSION AND HYDRAULIC SYSTEM OIL FILTERS NOTE: With the exception of the first oil filterchange after the 25 hour break-in period, thehydrostatic transmission and hydraulic system oilfilters should be changed along with the hydrostatictransmission / hydraulic system oil ...

40 LUBRICATION OF DRIVE SHAFT Lubricate both ends of the drive shaft after every 50hours of operation as follows: • The front end of the drive shaft can beaccessed from under the hood, and the rearend by removing the six screws and the centerfender cover. The drive shaft can also beaccessed from the...

41 TRACTOR STORAGE If your tractor is not going to be operated for anextended period of time (thirty days to approxi-mately six months), the tractor should be preparedfor storage. Store the tractor in a dry and protectedlocation. If stored outside, cover the tractor (includ-ing the tires) to protect...

42 SECTION 5: ENGINE INFORMATION AND MAINTENANCE KAWASAKI LIMITED WARRANTY CALIFORNIA AND FEDERAL EMISSIONS CONTROL SYSTEMS SMALL OFF-ROAD ENGINES The California Air Resources Board, the Environmental Protection Agency (EPA) , and Kawasaki Motors Corp.,U.S.A. (hereinafter “Kawasaki”) are pleased to ...

43 3. LIMITED LIABILITY. (a) The liability of Kawasaki under this Emission Control Systems Warranty is limited solely to the remedying of defects in materials or workmanship by any authorized Kawasaki small off-road engine dealer at itsplace of business during customary business hours. This warranty...

44 ENGINE MAINTENANCE WARNING: Use care when servicingany component in the engine area. Ifthe engine has recently been operated,components will be hot and couldcause burns. Allow the engine to coolbefore servicing. WARNING: Before servicing the engine,place the tractor on a level surface,stop the en...

46 • Turn the valve drain cock fully clockwise toclose the valve, and clean any residual oil fromthe valve. Refer to Figure 52. • Apply a light coating of clean oil on the gasket ofthe new oil filter. Thread the filter on by handuntil the gasket contacts the filter mounting sur-face, then tighten th...

47 INSPECTION OF COOLING SYSTEM HOSES Check the cooling system hoses for any cracks ordeterioration every 200 hours of operation. Checkall hose connections for looseness. Replace anydamaged hoses and tighten any loose connections. CHANGING THE ENGINE COOLANT The engine coolant should be drained and ...

48 SERVICING THE FOAM PRECLEANER Wash the foam precleaner every 25 hours ofoperation. Wash more often when operating underextremely dusty conditions. Replace the precleanerif torn or otherwise damaged. Referring to Figure 56, wash the precleaner asfollows: • Remove the knob and lift off the air clea...

49 SECTION 6: SPECIFICATIONS Engine Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . KawasakiHorsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

50 SPECIFICATIONS Hydraulic Lift System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auxiliary Pump-GearControl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Position Contr...

51 SECTION 7: OPTIONAL EQUIPMENT AND ACCESSORIES When purchasing your tractor, you probably had it equipped for your particular needs at that time.You may later wish to obtain additional equipment or accessories to perform other tasks. Refer to thechart below for a list of optional equipment and acc...