Crosley CGD7464GW0 - Manuals

6 Installation spacing for recessed area or closet installation All dimensions show recommended and minimum spacing allowed. ■ Additional spacing should be considered for ease of installation and servicing. ■ Additional clearances might be required for wall, door, floor moldings, dryer venting, and ...

7 ELECTRIC DRYER POWER HOOKUP – CANADA ONLY ELECTRICAL REQUIREMENTS It is your responsibility: ■ To contact a qualified electrical installer. ■ To be sure that the electrical connection is adequate and in conformance with Canadian Electrical Code, C22.1 – latest edition and all local codes. A copy o...

8 †®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company. GAS SUPPLY LINEOption 1 (Recommended Method) Flexible stainless steel gas connector: ■ If local codes permit, use a new flexible stainless steel gas connector (Design Certified by the American Gas Association or CSA Internat...

9 *5 3 / 4 " (146 mm) 1 1 / 2 " (38 mm) 3 ⁄ 8 " NPT dryer gas pipe GAS SUPPLY CONNECTION REQUIREMENTS ■ Use an elbow and a 3 ⁄ 8 " flare x 3 ⁄ 8 " NPT adapter fitting between the flexible gas connector and the dryer gas pipe, as needed to avoid kinking. ■ Use only pipe-joint comp...

10 Venting Requirements VENTING WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.IMPORTANT: Observe all governing codes and ordinances. Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only...

11 Plan Vent System Choose your exhaust installation type Recommended exhaust installation: A. DryerB ElbowC. WallD. Exhaust hoodE. Clamps F. Rigid metal or flexible metal vent G. Vent length necessary to connect elbows H. Exhaust outlet A B C D E F B G H Optional exhaust installations: This dryer c...

12 Install Vent System 1. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) 2. Connect vent to exhaust hood Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood. Vent must fit over the exhaust hood. Secure vent to exhaust hood with 4" (1...

13 CONNECT INLET HOSE (STEAM MODEL ONLY) For non-steam models, skip to “Connect Vent.” The dryer must be connected to the cold water faucet using the new inlet hoses (not supplied). Do not use old hoses. NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose i...

14 CONNECT VENT 1. Connect vent to exhaust outlet 2. Move dryer to final location Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is...

15 2. Adjust leveling legs If dryer is not level, prop up using a wood block, use wrench to adjust legs up or down, and check again for levelness. Once dryer is level, make sure all four legs are snug against the floor and the dryer does not rock. LEVEL DRYER 1. Level dryer Place level here Not Leve...

17 5. Reverse outer window assembly Using a Phillips screwdriver, remove the 4 screws from the outer window retainer and lift off the trim ring off the window (A). Rotate trim ring 180° and secure with the 4 screws removed earlier (B). Using a Phillips screwdriver, remove the 2 screws from the outer...

18 8. Reinstall hinge and latch on opposite sides Using a T25 ® screwdriver, reinstall the latch plate, latch backing plate, and hinge assembly on the opposite sides from which they were removed. 7. Remove hinge and latch Using a T25 ® screwdriver, remove the 3 screws securing the latch plate and la...

20 1. Remove door from dryer IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding. Using a T25 ® screwdriver, remove the 4 screws securing the door hinge to the dryer and lift up and out to remove the door. Place the door on a...

22 1. Remove door from dryer IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding. Using a T25 ® screwdriver, remove the 4 screws securing the door hinge to the dryer and lift up and out to remove the door. Place the door on a...

24 2. Move the door strike Using a T25 ® screwdriver, remove the 2 screws securing the door strike to the door frame of the dryer. Remove the 4 screws above and below the door strike and set aside for later use. Rotate the strike 180° and attach to the opposite side of dryer door frame, as shown. 3....