Crosley CED7464GW0 - Manuals

6 Then choose a 4-wire power supply cord with ring or spade terminals and UL-listed strain relief. The 4-wire power supply cord, at least 4 ft. (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either gree...

7 INSTALL LEVELING LEGS To avoid damaging floor, place a large flat piece of cardboard from dryer carton under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard. Examine leveling legs and locate diamond marking. Screw legs into leg holes by...

8 Power supply cord strain relief Power Supply Cord Connection 2. Attach power supply cord to strain relief 1. Attach power supply cord strain relief D C B A Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The st...

10 Direct Wire Connection Direct wire strain relief 1. Attach direct wire strain relief C B A 2. Attach direct wire cable to strain relief Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL-listed strain relief (UL marking on strain relief). Put the threaded sectio...

13 Connect a separate copper ground wire (G) under the green external ground conductor screw (A) to an adequate ground. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now go to “Venting Requirements.” 4. Connect external ground wire G ...

14 Special provisions for mobile homes: Exhaust vent must be securely fastened to a noncombustible portion of mobile home and must not terminate beneath the mobile home. Terminate exhaust vent outside. Optional exhaust installations: This dryer can be converted to exhaust out the right side, left si...

15 The “Vent System Charts” provide venting requirements that will help achieve best drying performance. Determine vent path: ■ Select route that will provide straightest and most direct path outdoors. ■ Plan installation to use fewest number of elbows and turns. ■ When using elbows or making turns,...

17 CONNECT VENT 1. Connect vent to exhaust outlet 2. Move dryer to final location Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is...

18 IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding. Using a T25 ® screwdriver, remove the 4 screws securing the door hinge to the dryer and lift up and out to remove the door. Place the door on a soft towel or other non-s...

20 With the edge with 2 notches at the top, align the notches on the outer window assembly with the tabs on the trim ring and lower into place as shown in figure A. Rotate the outer window assembly counterclockwise to lock tabs into place (figure B). Using a Phillips screwdriver, secure with 2 screw...

22 3. Remove inner door from outer door Position the door with the inside of the door facing up. Using a Phillips screwdriver, remove the 10 screws securing the inner door to the outer door. Lift off the inner door and set aside. 4. Remove hinge and latch Using a T25 ® screwdriver, remove the 3 scre...

24 4. Remove hinge and latch Using a T25 ® screwdriver, remove the 3 screws securing the latch plate and latch backing plate and the 5 screws holding the hinge assembly in place. Hinge Latch 5. Reinstall hinge and latch on opposite sides Using a T25 ® screwdriver, reinstall the latch plate and latch...

25 7. Reinstall door on dryer Using a T25 ® screwdriver, remove the 4 screws on the dryer. Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. Secure in place with the 4 T25 ® screws removed earlier. 2. Move the door strike Using a T25 ® screwdriver, remove the ...