Craftsman 486.24222- Manuals

Page 2 - TWO YEAR FULL WARRANTY ON CRAFTSMAN LAWNSWEEPER; Stay off of steep slopes.; SAFETY

2 TWO YEAR FULL WARRANTY ON CRAFTSMAN LAWNSWEEPER When assembled, operated and maintained according to the supplied instructions, if this Craftsman Lawnsweeper fails due to a defect in material or workmanship within two years from the date of purchase, call 1-800-4-MY-HOME to arrange for free repair...

Page 3 - CARTON CONTENTS; ACCESSORIES AND ATTACHMENTS

3 CARTON CONTENTS (Loose Parts in Carton) 11. Rear Hopper Tube (2) 12. Upper Hopper Tube (2)13. Lower Hopper Tube (2)14. Pivot Rod15. Hopper Support Strap (2)16. Bag Frame Strap 1. Sweeper Housing Assembly2. Bag Arm Tube (2)3. Hitch Tube, L.H. (Left Hand)4. Hitch Bracket Assembly5. Hitch Bracket, Be...

Page 4 - HARDWARE PACKAGE CONTENTS; SHOWN FULL SIZE

4 REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION K 1 Spacer Bushing, L 1 Hairpin Cotter, 1/8" M 8 Hairpin Cotter, 3/32" N 2 Clevis Pin, 3/8" x 1/2" O 4 Clevis Pin, 1/4" x 1-1/8" P 2 Clevis Pin, 1/4" x 1-3/4" Q 4 Hopper Clamp R 4 Plastic Plug S 2 Vinyl Cap T 1 Grip U 1 Kn...

Page 5 - TOOLS REQUIRED FOR ASSEMBLY; ASSEMBLY; STEP 5 - MEASURE TRACTOR HITCH HEIGHT

5 STEP 4 - ASSEMBLE HEIGHT ADJ. STRAP • Place the spacer bushing (I) into the hole in the height adjustment strap. Place the strap and bushing between the hitch tubes, aligning them with the rear hole. Fasten the hitch tubes together, with the strap and bushing between them, using two hex bolts (A) ...

Page 7 - ASSEMBLY OF HOPPER BAG; STEP 10 - ASSEMBLE UPPER TUBES; STEP 11 - ASSEMBLE LOWER TUBES; NOTE: Either side of the rear hopper tube can face up.; STEP 12 - ASSEMBLE TUBES TO BAG

7 ASSEMBLY OF HOPPER BAG STEP 10 - ASSEMBLE UPPER TUBES • Fit the ends of the two upper hopper tubes into the ends of a rear hopper tube. Align the holes in the ends of the tubes and insert plastic plugs (R). See ﬁ gure 7. NOTE: Either side of the rear hopper tube can face up. FIGURE 7 FIGURE 9 UPPE...

Page 8 - STEP 14 - ASSEMBLE HOPPER CLAMPS; STEP 13 - ATTACH BAG BOTTOM; BAG FRAME STRAP

8 STEP 14 - ASSEMBLE HOPPER CLAMPS • Assemble two hopper mount clamps (Q) over the hole in the middle of each upper hopper tube using two carriage bolts ( E) and two nylock nuts (F). Tighten only ﬁ nger tight. See ﬁ gure 14. • Fold the bag ﬂ aps around the lower hopper tubes and attach to the bag bo...

Page 9 - MOUNTING CLAMP

9 FIGURE 17 STEP 15 - ASSEMBLE PIVOT ROD • Slide the end of the pivot rod through the upper hopper tube and the hopper mount clamps on one side of the hopper. Place a hopper support strap and then a bag arm tube onto the rod. Slide the rod through the stitched sleeve at the front edge of the wind sc...

Page 10 - ATTACHING SWEEPER HITCH TO TRACTOR

10 ATTACHING SWEEPER HITCH TO TRACTOR BLACK LINE IS TRACTOR HITCH HITCH BRACKET MOUNTEDBELOW HITCH TUBES BLACK LINE IS TRACTOR HITCH HITCH BRACKET MOUNTEDABOVE HITCH TUBES • Place the tractor and sweeper on a ﬂ at level surface. • Set the sweeper height adjustment handle to about the middle of its a...

Page 11 - KNOW YOUR SWEEPER; Never attach the hopper rope; OPERATION; HOW TO USE YOUR SWEEPER

11 KNOW YOUR SWEEPER CAUTION: Keep sweeper away from ﬁ re. Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to burn. CAUTION: Never attach the hopper rope to any part of your body or clothing! Never hold onto the rope while towing the sweeper! Attach the ...

Page 12 - MAINTENANCE; CLEANING; SCHEDULED MAINTENANCE; Before storing the sweeper,; STORAGE

12 MAINTENANCE MAINTENANCE SCHEDULE Fill in dates as you complete regular service. Check for loose fasteners X Check for worn or damaged parts X X Lubricate brush shaft bearings X Lubricate wheel bearings X Clean Sweeper X X Clean/Lubricate chain and sprockets X Check for loose fasteners X Check for...

Page 13 - SPROCKET, CHAIN AND PAWL SERVICE; Make notes on the; BRUSH REPLACEMENT; NOTE: Brush replacement should be done one brush at; SERVICE AND ADJUSTMENTS

13 SPROCKET, CHAIN AND PAWL SERVICE IMPORTANT: Do not remove both wheels at the same time to avoid mixing of parts. (The R.H. and L.H. ratchet sprockets are not interchangeable.) Make notes on the position of washers and snap rings during disassembly. • Remove the dust cover by removing the two rive...

Page 14 - PARTS

14 PARTS A C A A C D D B B 15 14 16 39 17 18 19 47 56 55 56 20 41 28 30 31 55 25 26 36 38 23 26 24 29 40 14 81 34 79 22 37 21 37 20 64 76 75 28 2 11 12 13 59 33 81 7 5 4 52 61 63 66 60 49 58 59 68 51 50 69 57 67 65 62 59 1 9 27 8 9 10 32 6 3 80 78 77 28 70 59 83 75 43 42 44 48 45 72 73 75 75 71 71 4...

Page 16 - Your Home; in your home; Our Home; Para pedir servicio de reparación

® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC ® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC Get it fixed, at your home or ours! Your Home For repai...