Craftsman 351.215- Manuals

Page 2 - BE PREPARED FOR JOB

2 TABLE OF CONTENTS Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly ...

Page 3 - MOUNT SANDER; SAFETY

• Turn machine off if it jams. • Support workpiece with work table. CAUTION: Think safety! Safety is a combination of operator common sense and alertness at all times when tool is beingused. WARNING: Do not attempt to operate tool until it is com- pletely assembled according to the instructions. UNP...

Page 4 - ONBOARD STORAGE; INSTALLATION

ONBOARD STORAGE Onboard storage is provided for all drums, inserts and washers. INSTALLATION Refer to Figures 6, 7 and 8, pages 4 and 5. POWER SOURCEWARNING: Do not connect sander to the power source until all assembly steps have been completed. The motor is designed for operation on the voltage and...

Page 5 - OPERATION; DESCRIPTION; OPERA

EXTENSION CORDS • The use of any extension cord will cause some drop in voltage and loss of power. • Wires of the extension cord must be of sufficient size tocarry the current and maintain adequate voltage. • Use the table to determine the minimum wire size (A.W.G.)extension cord. • Use only 3-wire ...

Page 6 - BASIC SANDING OPERATION; DUST COLLECTION; MAINTENANCE; CLEANING

The sander can be locked from unauthorized use by lockingthe switch. To lock the switch: • Turn the switch to OFF position and disconnect sanderfrom power source. • Pull the key out. The switch cannot be turned on with thekey removed. NOTE: Should the key be removed from the switch at the ONposition...

Page 7 - TROUBLESHOOTING; SYMPTOM

7 MAINTENANCE TROUBLESHOOTING SYMPTOM Motor will not start Motor will not start; fuses blown or circuit breakers are tripped Motor fails to develop fullpower (power output ofmotor decreases rapidlywith decrease in voltage atmotor terminals) Motor overheats Motor stalls (resulting inblown fuses or tr...

Page 8 - Figure 11 - Replacement Parts Illustration for Sander

8 Figure 11 - Replacement Parts Illustration for Sander Model 351.215000 59 13 58 30 31 29 33 22 33 22 35 34 32 17 65 26 25 15 21 22 23 20 66 24 40 39 28 60 61 5 62 43 38 36 36 44 57 8 14 10 37 37 37 42 18 2 12 12 1 27 27 7 54 56 51 51 48 46 46 47 47 50 19 63 49 41 52 45 45 9 9 6 4 3 55 64 16 11 11 ...

Page 9 - S LIST; REPLACEMENT PARTS LIST FOR SANDER

9 P A R T S LIST * Standard hardware item available locally Δ Not shown REPLACEMENT PARTS LIST FOR SANDER Recommended Accessories Δ ¾ ″ Abrasive Sleeves, 3 pc. (50, 80, & 120 grit) 9 - 24137 Δ 1 ″ Abrasive Sleeves, 3 pc. (50, 80, & 120 grit) 9 - 24138 Δ 1½ ″ Abrasive Sleeves, 3 pc. (50, 80, ...

Page 10 - Service Record; Craftsman Oscillating Spindle Sander

10 Service Record Craftsman Oscillating Spindle Sander DATE MAINTENANCE PERFORMED REPLACEMENT PARTS REQUIRED

Page 11 - NOTES

Page 12 - Your Home; in your home; Our Home; Sears Parts & Repair Service Center; Para pedir servicio de reparación

® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC ® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC Get it fixed, at your home or ours! Your Home For exper...