Page 2 - TABLE OF CONTENTS
i 90914 TABLE OF CONTENTS Page GENERAL INFORMATION 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION INSTRUCT...
Page 3 - LIST OF TABLES
ii 90914 TABLE OF CONTENTS (cont’d) LIST OF TABLES Page TABLE 1. SPECIFICATIONS 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TABLE 2. LBS./24-HOUR ICE PRODUCTION 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TABLE 3. HARVEST CYCLE 1 . . . . ...
Page 4 - GENERAL INFORMATION; DESCRIPTION; Table 1. SPECIFICATIONS; Water Temperature
1 90914 GENERAL INFORMATION DESCRIPTION The Remcor S.I.D. (Spiral Ice Maker/Dispenser) is a unique, self-contained, counter top style unit that automati- cally makes hard, clear cube-quality ice and stores it in a sealed hopper for sanitary dispensing. The ice is made by a new, patented process on a...
Page 5 - INSTALLATION INSTRUCTIONS; UNPACKING INSTRUCTIONS; ice maker evaporator and void the extended evaporator warranty.
2 90914 INSTALLATION INSTRUCTIONS UNPACKING INSTRUCTIONS 1. With the unit upright, carefully remove the shipping crate. Inspect for shipping damage and report any such damage to the shipper immediately. 2. Open the hinged service door and remove shipping tape from the ice drop cover, storage hopper ...
Page 6 - following basic systems:; for more information on this product.
3 90914 IMPORTANT: To ensure proper ice maker operation and also to reduce the frequency of water-related service problems, a water filter should be installed. Remcor recommends the use of one of the following basic systems: 1 . Everpure, Inc. 2. System IV 660 No. Blackhawk Drive 16632 Burke Lane We...
Page 10 - BEVERAGE SYSTEM; Installation; hopper with power applied to unit.
7 90914 BEVERAGE SYSTEM “B”models contain beverage faucets only and must be supplied with cold product from any remote cold plate or refrigerated soda factory. “BC”units have a built-in cold plate, in addition to the beverage faucets and are de- signed to be supplied directly from syrup tanks and ca...
Page 13 - OPERATING INSTRUCTIONS; Table 3. HARVEST CYCLE
10 90914 OPERATING INSTRUCTIONS A temperature sensing control bulb located in the storage hopper starts and stops the ice making process in response to ice level in the hopper. With this ice level control “calling”for ice (hopper ice level is low), ice begins to form on the stainless steel tubing co...
Page 16 - FIGURE 9. REFRIGERATION SCHEMATIC
Page 17 - MAINTENANCE; REGULAR BASIS; Cleaning Instructions; EVERY THREE MONTHS; Maintenance/Adjustment; PERIODICALLY; both the ice maker and hopper.; Ice Maker Section
14 90914 MAINTENANCE REGULAR BASIS (or as required) Cleaning of the ice maker is recommended on a regular basis not only for sanitary reasons, but also to maintain the performance of the unit. Build-up of lime and scale can hinder ice making production rates and interfere with proper dispensing of t...
Page 18 - to remove all traces of the cleaning solution from the evaporator.; Dispenser Section; Note: It may be helpful to twist cover slightly.; For Units With Beverage System
15 90914 6. Push manual water fill switch and fill evaporator with water (approximately 5 seconds). 7. Put the “Clean/Run”switch in the “clean”position. Allow unit to run in the cleaning mode for at least 30 minutes. 8. Put the “Clean/Run”switch in the “run”position. 9. Depress the “Flush”switch pus...
Page 20 - TROUBLESHOOTING GUIDE
17 90914 TROUBLESHOOTING GUIDE The following pages contain troubleshooting charts designed to aid an experienced service person in diagnosing any operating problem which may be experienced. It is assumed that normal service techniques and skills are familiar to the person doing the troubleshooting. ...
Page 33 - MAINTENANCE/ADJUSTMENT PROCEDURES; THERMOSTAT ALTITUDE ADJUSTMENTS; COUNTERCLOCKWISE TURN; CLEARING EVAPORATOR FREEZE-UP; hopper with power applied to the unit.
30 90914 MAINTENANCE/ADJUSTMENT PROCEDURES THERMOSTAT ALTITUDE ADJUSTMENTS IMPORTANT: Adjust the bin thermostat setting only if storage hopper over fill is a problem. BIN THERMOSTAT 1. Open the hinged service door. 2. The adjustment screw is located below the “Flush”switch on the left side of the el...
Page 34 - CLEANING THE CONDENSER
31 90914 ICE THICKNESS ADJUSTMENT WARNING: Do not adjust ice thickness probe unless all other problem causes have been evaluated. 1. Open the hinged service door and remove the ice drop and hopper covers. 2. Collect and weigh the ice produced during the harvest cycle. The amount of ice harvested sho...
Page 35 - HARVEST TIME ADJUSTMENT; viewed from the front of the unit.; MANUAL FILLING
32 90914 HARVEST TIME ADJUSTMENT WARNING: Disconnect electrical power to the unit before servicing the timer in the electrical box. 1. Disconnect power to ice maker. 2. Open the hinged service door and remove the electrical control box cover. 3. Place the “Stop/Run”switch in the “Stop”position. 4. U...
Page 36 - FIGURE 10. HARVEST TIMER
Page 37 - PARTS LIST
34 90914 PARTS LIST DESCRIPTION PART NUMBERS Air Cooled Water Cooled Dispenser Components 250 250 “BC” 250 250 “BC” Gate Slide 21491 21491 21491 21491 Depressor Lever 22777 22777 22777 22777 Depressor Retainer 22644 22644 22644 22644 Agitator 23692 23692 23692 23692 Vend Switch 30895 30895 30895 308...
Page 39 - WARRANTY; IMI Cornelius Offices
36 Manual number IMI CORNELIUS INC . O NE C ORNELIUS P LACE A NOKA, MN . 55303--6234 T ELEPHONE (800) 238--3600 F ACSIMILE (612) 422--3232 T ECH S VC 1-800-535-4240 WARRANTY IMI Cornelius Inc. and Remcor Products Company warrants that all equipment and parts are free from defects in material and wor...
Page 40 - Remcor Incorporated
CORPORATE HEADQUARTERS: Remcor Incorporated 500 Regency Drive Glendale Heights, IL 60139 708. 980.6900