Compaq H9A11 - Manuals

vi Organization This guide is organized as follows: Chapter 1, Introduction -- Provides an overview of the H9A11 Cabinet features andspecifications. Chapter 2, Installation -- Provides site preparation, unpacking, and installationinformation. Appendix A, Field Replaceable Units (FRUs) -- Provides a ...

vii Reader's Comments Compaq welcomes your comments on this or any other manual. You can send yourcomments to Compaq in the following ways: • Internet electronic mail: [email protected] • Mail: Compaq Computer Corporation Information Design PKO3-2/21J 129 Parker Street Maynard, MA 01754-21...

H9A11 Cabinet Installation/Owner’s Guide 1–1 1 Introduction 1.1 Description The H9A11 Cabinet (Figure 1-1) is a low-cost, computer-equipment enclosure system thatmeets the Electronic Industries Association (EIA) standard 310C and the InternationalElectrotechnical Commission (IEC) 297 standards and c...

Introduction 1–2 H9A11 Cabinet Installation/Owner’s Guide Figure 1-1 H9A11 Cabinet J 1 Not f o r e xter nal loads s c a l e = . 1 2 L J - 0 4 8 0 3 s c a l e = . 9

Introduction 1–3 H9A11 Cabinet Installation/Owner’s Guide 1.2 Specifications Specifications for the H9A11 Cabinet are as follows: Physical Height, overall 110.0 cm (43.31 in.) Width, overall 60.0 cm (23.60 in.) Depth, overall 86.0 cm (33.86 in.) Maximum vertical rackmounting space 93.35 cm (36.75 in...

Introduction 1–4 H9A11 Cabinet Installation/Owner’s Guide Power cord (attached) H7600-AA - 120 Vac with L5-30PconnectorH7600-AB - 240 Vac with L6-20PconnectorH7600-DB - 240 Vac with IEC 309connector

H9A11 Cabinet Installation/Owner's Guide 2–1 2 Installation 2.1 Introduction This chapter provides the following information: • Tools Required (Section 2.2) • Site Planning (Section 2.3) • Unpacking (Section 2.4) • Installation Procedures (Section 2.5) 2.2 Tools Required The tools needed to install ...

Installation 2–2 H9A11 Cabinet Installation/Owner's Guide _______________________ WARNING __________________________ High Leakage Current --- An insulated earthing conductor that is identical insize, insulation material, and thickness to the earthed and unearthed branch-circuit supply conductors (ex...

Installation H9A11 Cabinet Installation/Owner's Guide 2–3 2.4 Unpacking The cabinet is shipped on a wooden pallet. Proceed as follows to unpack the cabinet: 1. Position the pallet with the cabinet in an area that provides sufficient workspace forunpacking. Ensure that there is sufficient clearance i...

Installation 2–4 H9A11 Cabinet Installation/Owner's Guide Figure 2-1 Unpacking the Cabinet F F L J - 0 4 8 0 4 2 2 3 2 5 4 J1 Not f o r e x ter nal loads s c a l e = . 1 2 J1 Not f o r e x ter nal loads 1

Installation H9A11 Cabinet Installation/Owner's Guide 2–5 6. Refer to Figure 2-2. Remove the four shipping bolts ž and brackets Ÿ that secure the four cabinet leveler feet   to the pallet œ. __________________________ Note _____________________________ The ramps attach to the front of the pallet. Th...

Installation 2–6 H9A11 Cabinet Installation/Owner's Guide Figure 2-2 Installing the Ramps LJ-04805 10 1 4 9 2 J 1 Not f o r e xter nal loads s c a l e = . 1 2 3 6 7 8

Installation H9A11 Cabinet Installation/Owner's Guide 2–7 ________________________ WARNING __________________________ In the following step, use sufficient personnel to move the cabinet off thepallet. The cabinet weighs 80.74 kg (178 lb) empty, and can weigh up to420.94 kg (928 lb) fully configured....

Installation 2–8 H9A11 Cabinet Installation/Owner's Guide Figure 2-3 Deskidding the Cabinet LJ-04806 J 1 Not f o r e xter nal loads s c a l e = . 1 2

Installation H9A11 Cabinet Installation/Owner's Guide 2–9 2.5 Installation Procedures During the installation of the cabinet, one or more of the following procedures may beneeded: • Removing and Replacing the Rear Lift-Off Door (Section 2.5.1) • Removing and Replacing the Front Filler Panels (Sectio...

Installation 2–10 H9A11 Cabinet Installation/Owner's Guide 2.5.1 Removing and Replacing the Rear Lift-Off D o or The rear lift-off door provides access into the rear of the cabinet. To remove the rear lift-offdoor, refer to Figure 2-4 and proceed as follows: Removal 1. Remove the two Phillips-head s...

Installation H9A11 Cabinet Installation/Owner's Guide 2–11 Figure 2-4 Removing and Replacing the Rear Lift-Off Door M A IN P OWER L J - 0 4 8 0 7 2 3 1 4

Installation 2–12 H9A11 Cabinet Installation/Owner's Guide 2.5.2 Removing and Replacing the Front Filler Pa n els To remove a front filler panel, refer to Figure 2-5 and proceed as follows: Removal Grasp the front filler panel ™ on both sides and then pull straight back away from the cabinet. Replac...

Installation H9A11 Cabinet Installation/Owner's Guide 2–13 Figure 2-5 Removing and Replacing the Front Filler Panels J 1 Not f o r e xter nal loads s c a l e = . 1 2 L J - 0 4 8 0 8 s c a l e = . 9 1 2 3 4 1 2 3 4

Installation 2–14 H9A11 Cabinet Installation/Owner's Guide 2.5.3 Pulling Out and Adjusting the Stabilizer Bar The stabilizer bar ™ pulls straight out from the bottom front of the cabinet š as shown in Figure 2-6. When the stabilizer bar is fully extended, adjust the foot › at the end of the stabiliz...

Installation H9A11 Cabinet Installation/Owner's Guide 2–15 Figure 2-6 Pulling Out and Adjusting the Stabilizer Bar J 1 Not f o r e xter nal loads 2 S c a l e = . 1 2 t h e n . 7 2 1 3 L J - 0 4 8 0 9

Installation 2–16 H9A11 Cabinet Installation/Owner's Guide 2.5.4 Removing and Replacing the Power Distribu t ion Unit _______________________ WARNING __________________________ There can be one or more PDUs per cabinet. Ensure that all systems installedin the cabinet are turned off as described in t...

Installation H9A11 Cabinet Installation/Owner's Guide 2–17 Figure 2-7 Removing and Replacing the Power Distribution Unit L J - 0 4 8 1 0 M A I N P OW E R 3 3 5 M A I N P OW ER 1 2 J 1 J 2 J 3 J 4 J 5 Not f o r e x ter nal loads Ne s’appliqu pas a l’alimentation ex te rn e . 4 4