Coleman 9992-644 - Manuals

5 DANGER • DO NOT insert any foreign objects into the valve outlet. You may damage the valve. A damaged valve can cause a leak,which could result in explosion, fire, severe personal injuryor death. WARNING • Cylinders must be stored outdoors out of the reach of children and must not be stored in a b...

6 WARNING Handle a full cylinder with care. Gas is under high pressure. DANGER • NEVER store a spare L.P. gas supply cylinder under the grill body or inside the grill enclosure or in the vicinity of any heatproducing appliance. (Fig. 3) • NEVER fill the cylinder beyond 80% full. Failure to follow th...

7 1 3 4 5 6 7 8 9 10 11 12 2 13 1. Grill Hood 2. Thermometer 3. Hood Handle 4. Control Knob: Side Burner 5. Electronic Igniter: Main, Side,and Rear Infrared Burner. 6. Convection Vents 7. Cart with Doors 8. Control Knobs: Main Burners 9. Control Knob: Rear Infrared Burner 10. Side Shelf 11. Grilling...

1 2 3 6 5 4 11 9 8 10 14 1. 9992-4131 Hood Assembly w/Logo Plate 2. 9992-4141 Hood Handle Assembly 3. 9992-1111 Temperature Gauge Only 4. 9992-2731 Back IR Cover 5. 9992-1301 Warming Rack 6. 9992-4061 Back IR Burner Assembly LP 7. 9992-4071 Back IR Electrode Assembly 8. 9992-4081 Main Burner Electro...

1. Place a piece of styrofoam from the packaging in the grill toleave the grill hood propped open slightly (Fig. 6). 2. Position the side shelf hooks with the slots on the side of thegrill, near the back (Fig. 7). 3. Position the side shelf flange over the inside top edge of the grill(Fig. 8). Push ...

Side Burner Installation Grill Assembly — 8200 Series 11 Fig. 12 4. Secure the rear of the shelf by inserting (1) self tapping screw inthe back of the grill and through the shelf tab (Fig. 16). Fig. 13 Fig. 14 Fig. 16 Fig. 15 1. Position the side shelf hooks with the slots on the side of thegrill, n...

Fig. 25 Fig. 26b Fig. 23 11. Assemble the plastic hex nut and igniter button back ontothe electrode module. These items should be handtightened only (Fig. 23). Grill Assembly — 8200 Series Fig. 24 13. The igniter wire for the side burner is shipped loose. Attach thelarge spade to the igniter termina...

14 Cart Brace Installation 1. Open the grill doors. Two cart braces will be installed at an anglefrom the cart base to the back side of the compartment. The topend has a tab with a hole in the center. The bottom end has twoprotruding tabs. 2. For each cart brace, insert the two protruding tabs into ...

15 Grill Assembly — 8200 Series Fig. 36 Igniter Battery Installation 1. The AA battery, spring and igniter cap must be installed beforeusing (Fig. 36). 2. Install the AA battery, negative end first. 3. Slide the spring assembly over the battery. 4. Screw the igniter cap onto the igniter (Fig. 37). F...

16 IMPORTANT! T O ENSURE PROPER GAS FLOW , BURNER CONTROL VALVES MUST BE “OFF” BEFORE OPENING THE GAS CYLINDER VALVE . WARNING: During assembly of the grill and when attaching orreplacing the L.P. gas cylinder,insure that the gas supply hose isfree of kinks and/or damage andis at least 3 inches away...

18 NATURAL GAS CONVERSION KIT (not shown) Part Number Description 9992-214 8200 Series LP to NG Conversion Kit Natural Gas Installation NOTE: This step applies to you only if you are converting your 8200 Series grill to use NATURAL GAS. If you will be using your grill with LP GAS, this section does ...

19 DANGER T O P REVENT F IRE OR E XPLOSION H AZARD : • NO SMOKING. DO NOT use or permit sources of ignition in the area while doing a leak test. • Perform leak tests outdoors only.• NEVER perform a leak test with fire or flame. Leak Testing • If you detect a leak: 1. Turn off the fuel supply. Push i...

20 1. Regularly check the burner venturi tubes for blockage from an insect nest. Read “Cleaning the Venturi” in the section titled “Care,Maintenance, and Cleaning”, and also the section titled“Troubleshooting”. 2. Check that all the burner venturi [H] are set over the valve outlets [J] correctly. Th...

21 Lighting Main Burners Lighting Side Burner 1. Push and turn the side burner control knob counterclockwise to the “HIGH” position. (Fig. 49) 2. Immediately press and hold the electronic igniter button (Fig. 49). You will hear a snapping sound. 3. If the burner does not light in 4 seconds, turn the...

22 Using the Rotisserie — 8200 Series The grill rotisserie system is designed to cook items from the back using infrared heat. The rotisserie burner is aninfrared type which provides intense searing radiant heat. Preferred by chefs over other cooking methods, this intenseheat sears in the natural ju...

23 Lighting the Rotisserie Burner 1. Push and turn on the control knob for the ROTISSERIE BURNER counterclockwise to the “HIGH” position (Fig. 44 and 52). Wait 5 seconds. 2. Press and hold the electronic igniter button (Fig. 53). You will hear a snapping sound.3. If the burner does not light in 4 se...

24 Good Bad Yellow Blue Holes in Burner Yellow Blue Burner Control Setting Tips • The high flame setting is too hot for direct cooking. The high flame setting is good for quick searing of meat, then finishcooking on medium or low flame settings. • Use the high flame setting with the lid closed to pr...

25 Direct Method: • The heat source is directly below the food. • Use for browning meat or cooking hot dogs and hamburgers, but check food frequently. • Use for skillet and stir-fry cooking, but limit the amount of oil and heat to be used. • Cook roasts, turkey or duck on low heat. Place meat with w...

26 REPRESENTATIVE ILLUSTRATION Steps For Cleaning Venturi: 1. Remove the cooking grates and the heat tents and set aside.2. Using a 1/4” hex nut driver, remove the self-tapping screws holding the front heat shield (Fig. 58 and 59). Set the front heat shield aside. 3. Using a 1/4” hex nut driver, rem...

CAUTION All cleaning and maintenance should be done only when the grill is cool & with the fuel supply turned off at the cylinder.If your grill is set up for use with Natural Gas, turn off thegas supply at the system manual shut off valve. Suggested Cleaning Materials: • Mild dishwashing liquid ...

28 TYPE 1 CONNECTION ILLUSTRATION Thermal Sensitive Handwheel 1-5/16" Acme Connection Nipple with Excess Flow Valve Regulator YOUR NEW GAS GRILL IS EQUIPPED WITH ATYPE 1 CONNECTION DEVICE WHICH HAS 3SAFETY FEATURES (FIG. 64): 1. Proof of gas seal between the connector and the cylinder before gas...

Please do not send other correspondence to the address belo w. PRODUCT REGISTRA TION DEP AR TMENT PO BO X 2931 WICHIT A ,KS 67201 A TTN: DEPT 586 IMPORTANT! Coleman ¨ Grill Warranty Registration Card COMPLETE THE ATTACHED REGISTRATION CARD AND RETURN WITHIN 10 DAYS TO RECEIVE THESE IMPORTANT BENEFIT...

7) Side burner (if applies) 8) Steamer/Fryer/Warmer (if applies) 9) Side table design 10) Color of the grill (not including stainless steel) 11) Warming racks 12) Dependable igniter 13) Size of the grill (available cooking square inches) 14) Integrated storage cabinet 15) Price16) Rotisserie (if app...

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, KS 67219 U.S.A. 1-800-356-3612 • TDD: 316-832-8707 9992-030 (12/8/05) © 2005 The Coleman Company, Inc. All rights reserved. Coleman ® and are registered trademarks of The Coleman Company, Inc. Coleman Gas Barbecue Grill 5/1 Year Limited Warran...