Page 2 - Contents
2 DANGER • FOR OUTDOOR USE ONLY. NEVER operate grill in enclosed areas, as this could lead to gas accumulating from a leak, causing an explosion or a carbon monoxide buildup which could result in injury or death. DO NOT use in garages, breezeways, sheds or any enclosed area. (Fig. 1) • NOT FOR USE B...
Page 3 - Follow these safety rules before each use:; WARNING; General Installation
3 1 3 2 24" 8 7 36" (90cm) 36" (90cm) 36" (90cm) Clear REPRESENTATIVE ILLUSTRATION • Installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1 (USA), CAN/CGA-B149.1, Natural Gas Installation Code or CAN/CGA-B149....
Page 4 - CAUTION; Electrical Attachments
4 Longer detachable power-supply cords or extension cords must be used with care. The marked electrical rating of the cord set or extension cord must be at least as great as the electrical rating of the appliance. If the appliance is of the grounded type, the exten- sion cord should be a grounding-t...
Page 5 - Cylinder Specifications; Hose and Regulator
5 DANGER • DO NOT insert any foreign objects into the valve outlet. You may damage the valve. A damaged valve can cause a leak, which could result in explosion, fire, severe per- sonal injury or death. WARNING • Cylinders must be stored outdoors out of the reach of children and must not be stored in...
Page 6 - Transporting the Cylinder
6 WARNING Handle a full cylinder with care. Gas is under high pressure. DANGER • NEVER store a spare L.P. gas supply cylinder under the grill body or inside grill enclosure or in the vicinity of any heat producing appliance. (Fig. 12) • NEVER fill the cylinder beyond 80% full. Failure to follow this...
Page 8 - Step; LOOSELY
1-A . Arrange the two panels and the base on the ground as shown. Ö Ö LOOSELY assemble the Right Panel and the Left Panel to the Grill Base using one screw (TN) in each top corner. Ö Ö NOTE: Use a large piece of cardboard or a ground cloth to protect the painted finish on the grill. Step 1 1-B 1-B ....
Page 9 - Carefully; turn the assembly; Hardware shown actual size
Ö Ö Carefully turn the assembly up-side-down to performStep 2. This will give easyaccess to assemble theparts in Step 2. 2-A . Carefully turn the grill Up-Side-Down. 2-A Base (up-side-down) 2-B . Assemble eight additional screws (TN) to fasten the Side Panels to the base Base. Ö Ö Tighten all fasten...
Page 10 - M5 Locking Hex Nut; Locking Casters; Self Tapping Screw; Hardware shown actual size 4-C; Cylinder Support
Ö Ö NOTE: Use a ground cloth to protect the paint finishduring this step. 2-A . Carefully turn the grill Up-Side-Down. 3-A 3-A . Check that all fasteners are tightened before turning the grill Right-Side-Up. Ö Ö Carefully turn the grill Right-Side-Up. Ö Ö Engage the Locking Casters to prevent moveme...
Page 11 - M6 Locking Hex Nut; Door Magnet
Ö Ö Assemble the Top Panel. Ö Ö Assemble the RearSupport. 5-A 5-A . Assemble the Top Panel to the Left and Right Side Panels with eight Screws (TN). Hardware shown actual size TN (x8) Top Panel Ö Ö Install Door Magnets. 5-B 5-B . Assemble the Rear Support to the Left and Right Side Panels with eight...
Page 13 - . Assemble the Left Side Burner Table to the Firebox with; Left Side; UO
Ö Ö Assemble Left Side BurnerAssembly to the Firebox. Hardware shown actual size (CX) M6 x 20mm Screw (5) Qty. (UO) M6 Locking Hex Nut (1) Qty. 8-A 8-A . Assemble the Left Side Burner Table to the Firebox with five Screws (CX) and one Locking Hex Nut (UO). Placethe Locking Hex Nut in the center posi...
Page 15 - fasten the right side of the Firebox to the Grill Cart with three; LATER; Tighten all fasteners.; M6 Flat Washer
Ö Ö Fasten the Firebox to theGrill Cart. 10-A 10-A . LOOSELY fasten the right side of the Firebox to the Grill Cart with three Screws (TN), two Flat Washers (DY) and two Locking Hex Nuts (UO). Ö Ö NOTE: You will tighten these screws LATER (after Step 10-B), after the left side of the Firebox is atta...
Page 16 - . View showing Rear Trim Plate properly installed.
Ö Ö Fasten the Rear Trim Plateto the Grill Cart. (VP) Self Tapping Screw (2) Qty. Hardware shown actual size 11-A 11-A . Fasten the Rear TrimPlate to theFirebox withtwo Screws(VP). Ö Ö Tighten allfasteners. FIREBOX VP (x2) REAR TRIM PLATE VP Step 11 16 11-B 11-B . View showing Rear Trim Plate proper...
Page 17 - M5 x 15mm Flat Head Screw; . Fasten the Right Door to the Grill Cart with four Flat; RIGHT DOOR; TOOL HOOK
12-A Hardware shown actual size (XR) M5 x 15mm Flat Head Screw (8) Qty. Ö Ö Fasten both Left and RightDoors to the Grill Cart. Ö Ö Attach the Tool Hook to theRight Door. 12-C . Fasten the Right Door to the Grill Cart with four Flat Head Screws (XR). Ö Ö Repeat Step 12-C to attach the Left Door. Ö Ö ...
Page 19 - . Route the Side Burner Valve through the Large Hole in
14-A Ö Ö Install the Side BurnerValve. 14-B Side Burner Valve 14-A . Route the Side Burner Valve through the Large Hole in the Left Panel. Large Hole 14-C 14-E 14-D 14-C . Attach the Side Burner Valve with two Screws (WQ). WQ (x2) View from Below View From Back of Grill View from Above Side Burner V...
Page 20 - Hair Pin; M4 Hex Nut
15-D Ö Ö Assemble the Side Burnerto the Left Side Table. Ö Ö Assemble the Electrode tothe Side Burner. 15-A 15-B 15-A . Slip the Burner Tube through the Left Side Table. 15-D . View showing Side Burner properly installed. 15-B . Align Burner Tube with Burner Valve. Ö Ö NOTE: Make sure Burner Valve i...
Page 21 - : The fuel hoses are not; Note; : The polarity is marked on the Electrode
Ö Ö Assemble the ElectrodeWires and the Battery to theElectrode Module. Note : The fuel hoses are not shown in this step, forsimplicity. 16-A Side Burner Wire 9-Volt Battery Top Burner Wires Electrode Module 16-A . Slip the Top Burner Wires through the large hole in the Top Panel. Ö Ö Slip the Side ...
Page 22 - . Attach the Grease Cup Support to the Grease Pan with
Ö Ö Install Side Burner Knoband Side Burner Grate ontothe Left Side Burner. 17-A Side Burner Knob Side Burner Grate 17-A . Place the Side Burner Knob on the valve stem. Ö Ö Place the Side Burner Grate on the Left Side Burner.Align the pins downward into the alignment holes. Ö Ö Assemble the Grease C...
Page 23 - Rear Support; . Place the Grease Cup into the Grease Cup Support.; Grease Cup
Ö Ö Install the Grease Pan. Ö Ö Install the Grease Cup. 19-A 19-B 19-A . Slide the Grease Pan Assembly into the back of the grill. Ö Ö Tilt the pan slightly upward until the Grease Cup Supportclears the Rear Support. Rear Support 19-B . Place the Grease Cup into the Grease Cup Support. Note: Pull th...
Page 24 - During assembly of
Ö Ö Attach an LP Cylinder to theGrill. 20-A Cylinder Support LP Cylinder 20-A . Set LP Cylinder in the Cylinder Support with the outlet valve facing toward the front of the grill. 20-B 20-B . Tighten the Cylinder Hold-Down Bolt against the bottom cylinder collar. Cylinder Hold-Down Bolt 20-C Type 1 ...
Page 25 - the factory to use LP GAS, skip back to Step 20.
Ö Ö NOTE: Step 21 applies to you only if your grill is set up from the factory to use NATURAL GAS. If your grill is set up from the factory to use LP GAS, skip back to Step 20. Step 21 P LACE THE RUBBER PLUG ONTO THE GAS SUPPLY LINE . T HEN ATTACH THE SOCKET END OF THE QUICK DISCONNECT COUPLINGONTO ...
Page 26 - Leak Testing; How to Check for Leaks; Fixing A Fuel Leak
26 1. Check that the cylinder valve is closed by turning the cylinder knob clockwise to a full stop. 2. Check that all the grill burner knobs are in the off position. 3. Remove the protective caps from the cylinder valve and cou - pling nut. NOTE: The coupling nut connects to the large outside threa...
Page 27 - REPRESENTATIVE ILLUSTRATION; Lighting Instructions; Control Knobs for Main Cooking Area; Igniter Switch
CAUTION Inspect the gas supply hoses before each use. If there are cuts, damage, excessive abrasion or wear, replace the hosesprior to operating the appliance. During assembly of grill andwhen attaching or replacing the L. P. gas cylinder, insure thatall gas supply hoses are free of kinks and/or dam...
Page 28 - Match Lighting - Main Burners; Lighting Main Burners; Match Lighting - Side Burner; Shutting Off the Grill; Condition The Grill
28 1. Turn on any or all burner gas control knobs to high. (Fig. 19) 2. Press the igniter switch until the flame ignites. 3. If the flame doesn’t immediately light, turn off control knob and wait five minutes for gas to clear. 4. Repeat steps 1 through 3. 5. If the burner does not light on second tr...
Page 29 - Burner Control Setting Tips; General Use and Correct Burner Flames; Grilling Tips and Hints
Good Bad Yellow Blue Holes in Burner Yellow Blue Burner Control Setting Tips • The high flame setting is too hot for direct cooking. The high flame setting is good for quick searing of meat, then finish cooking on medium or low flame settings. • Use high flame setting with lid closed to preheat the ...
Page 30 - Steps For Cleaning Venturi:; Cleaning the Venturi; Cleaning and Maintenance; Suggested Cleaning Materials:
Steps For Cleaning Venturi: 1. Remove burner from grill bottom. 2. Look inside lower end of venturi tubes for nests, webs or mud. 3. To remove the above obstructions, use an accessory flexible venturi brush or bend a small hook on one end of a 20-inch- long flexible wire such as the one shown in Fig...
Page 31 - After moving the grill:; Moving and Storage; DANGER; Orifices; Problem: Burner will not light or has incom-
CAUTION A collision with the grill, as with any metal object, could cause injury. Use care when moving a portable gas grill. Moving the grill: • Move grill slowly. DO NOT run with or pull the grill behind you; it could hit you from behind causing injury. • DO NOT move the grill while it is lit or ho...
Page 32 - For Your Additional Safety; Troubleshooting
TYPE 1 CONNECTION ILLUSTRATION Thermal Sensitive Handwheel 1-5/16" Acme Connection Nipple with Excess Flow Valve Regulator YOUR NEW GAS GRILL IS EQUIPPED WITH A TYPE 1 CONNECTION DEVICE WHICH HAS 3 SAFETY FEATURES: (SEE TYPE 1 CONNECTION ILLUSTRATION) 1. Proof of gas seal between the connector a...
Page 33 - PRODUCT REGISTRA; Coleman; COMPLETE THE ATTACHED REGISTRATION CARD AND RETURN WITHIN 10; PROMOTE BETTER PRODUCTS:
Please do not send other correspondence to the address belo w. PRODUCT REGISTRA TION DEP AR TMENT PO BO X 2931 WICHIT A ,KS 67201 A TTN: DEPT 586 IMPORTANT! Coleman ¨ Grill Warranty Registration Card COMPLETE THE ATTACHED REGISTRATION CARD AND RETURN WITHIN 10 DAYS TO RECEIVE THESE IMPORTANT BENEFIT...
Page 34 - CONGRATULATIONS ON YOUR NEW COLEMAN
7) Side burner (if applies) 8) Steamer/Fryer/Warmer (if applies) 9) Side table design 10) Color of the grill (not including stainless steel) 11) Warming racks 12) Dependable igniter 13) Size of the grill (available cooking square inches) 14) Integrated storage cabinet 15) Price16) Rotisserie (if app...
Page 35 - Recipes; Cooking time after marination: 4-5 minutes; Lamb grilled with rosemary and Dijon; Cooking time after marination: 30-40 minutes
Recipes Lemongrass beef skewers with peanut dippingsauce Cooking time after marination: 4-5 minutes 2 pounds boneless sirloinFor the Marinade:3 cloves garlic, minced2 stalks lemongrass, trimmed of tough outer layer,sliced (find in Asian markets)2 Tb sugar1 Tb soy sauce3 Tb thai fish sauce (find in A...
Page 36 - Coleman Gas Barbecue Grill Limited Warranty; Warranty
Coleman Gas Barbecue Grill Limited Warranty Castings and Burners - Limited Lifetime Electronic Ignition Components - Limited Five (5) Years Cooking Surfaces and Other Parts - Limited Three (3) Years The Coleman Company, Inc. (“Coleman”) warrants that this product will be free from defects in materia...